Integrated Technologies of Testing and Controlling for High Efficiency Separate Layer Water Injection

2008 ◽  
Author(s):  
He Liu ◽  
Danfeng Xiao ◽  
Li Zhi Zhao ◽  
Fukun Zhang ◽  
Yumei Wang ◽  
...  
2008 ◽  
Author(s):  
He Liu ◽  
Danfeng Xiao ◽  
Li Zhi Zhao ◽  
Fukun Zhang ◽  
Yumei Wang ◽  
...  

Author(s):  
L. He ◽  
X. Danfeng ◽  
Z. Lizhi ◽  
Z. Fukun ◽  
W. Yumei ◽  
...  

2010 ◽  
Vol 44-47 ◽  
pp. 1470-1475
Author(s):  
Feng Shan Wang ◽  
De Li Jia ◽  
Shu Jin Zhang ◽  
Chong Jiang Liu ◽  
De Kui Xu

An identification-free adaptive control strategy based on expert amendment is proposed in this paper to solve the problem that it is difficult to establish mathematical model of water injection regulating process due to large time delay, strong nonlinearity and time variation in the flow control of separate layer water injection technology. In this control strategy, according to the past and current process information of water injection, the system output and trend can be estimated based on expert rules to amend the output of the identification-free adaptive control. The simulation result shows that this control strategy has perfect control performance and strong adaptability and it provides a feasible means for improving water injection effect.


Author(s):  
Tadashi Narabayashi ◽  
Yuuhei Sugano ◽  
Hiroki Imaeda ◽  
Go Chiba ◽  
Nobuaki Sato ◽  
...  

Fukushima Daiichi NPP accident would be terminated, if sufficient accident countermeasures, such as water proof door, mobile power, etc [1, 2]. In case of Europe, it had already installed the heat removal system and filtered containment venting system (FCVS) from the lessons of TMI and Chernobyl Accidents. The new regulatory standard in Japan, the filtered vent system (FCVS) should be installed, and prevent the radioactive material in case of the severe accident and the overpressure breakage prevention of a primary containment vessel (PCV) and also the robustization of the FCVS. The authors examined the severe accident process in the 2nd unit of Fukushima Daiichi NPS, and found the vent by FCVS should be done before water injection into the core. The PCV spray and water injection into the pedestal basement should be also the countermeasures to the severe accident. Countermeasures for an intentional aircraft collision should be installed too. Upon occurrence of a severe accident (SA), vent gas with radioactive fission products is blown out to a scrubbing pool through numerous venturi nozzles. Mist in steam moves upward to a metal fiber filter through a multi-hole baffle plate. After the mist is removed by that filter, radioactive methyl iodine (CH3I) is captured on the surface of a molecular sieve or AgX, made from zeolite particles with silver coating. A FCVS visualized test facility was installed at Hokkaido University. An AgX filter is used down-stream of the scrubbing pool and metal fiver filter. Thickness of AgX filter is very important parameter to obtain enough decontamination factor (DF). The DF for the radioactive iodine exceeds 10,000 at bed depth (AgX filter thickness) greater than 75mm.


2020 ◽  
Vol 10 (6) ◽  
pp. 6652-6668

Historically, smart water flooding is proved as one of the methods used to enhance oil recovery from hydrocarbon reservoirs. This method has been spread due to its low cost and ease of operation, with changing the composition and concentration of salts in the water, the smart water injection leads to more excellent compatibility with rock and fluids. However, due to a large number of sandstone reservoirs in the world and the increase of the recovery factor using this high-efficiency method, a problem occurs with the continued injection of smart water into these reservoirs a phenomenon happened in which called rock leaching. Indeed, sand production is the most common problem in these fields. Rock wettability alteration toward water wetting is considered as the main cause of sand production during the smart water injection mechanism. During this process, due to stresses on the rock surface as well as disturbance of equilibrium, the sand production in the porous media takes place. In this paper, the effect of wettability alteration of oil wetted sandstones (0.005,0.01,0.02 and 0.03 molar stearic acid in normal heptane) on sand production in the presence of smart water is fully investigated. The implementation of an effective chemical method, which is nanoparticles, have been executed to prevent sand production. By stabilizing silica nanoparticles (SiO2) at an optimum concentration of 2000 ppm in smart water (pH=8) according to the results of Zeta potential and DLS test, the effect of wettability alteration of oil wetted sandstones on sand production in the presence of smart water with nanoparticles is thoroughly reviewed. Ultimately, a comparison of the results showed that nanoparticles significantly reduced sand production.


2021 ◽  
Author(s):  
Yigang Liu ◽  
Zheng Chen ◽  
Xianghai Meng ◽  
Zhixiong Zhang ◽  
Jian Zou ◽  
...  

Abstract Nowadays intelligent injection is considered as a new frontier for offshore oilfield. In order to improve the water injection indicators such as allocation frequency and qualification rate, intelligent separate-layer injection technology (ISIT) was researched, deployed and optimized in B offshore oilfield from 2015. In the course of 5 years’ project operation, some experience of success or failure was achieved. B offshore oilfield is the largest offshore oilfield in China with 33 water flooding oilfields and more than 800 water injection wells. With the continuous development, the problem of injection management mainly reflected in the contradiction between increasing demand of allocation and limited operation time and space was exposed. Two kinds of ISIT, cable implanted intelligent separate-layer injection technology(CISIT) and wireless intelligent separate-layer injection technology(WISIT), were deployed to solve the above problem. CISIT controlled the distributor downhole by electricity while WISIT controlled the distributor downhole by pressure pulse. By the use of ISIT, downhole nozzle's action, packer testing and downhole data monitoring could be remotely controlled on the ground. During the 5 years’ test, ISIT was optimized from the field breakdown including large flow range flowing test, cable protection project, efficient coding mode, water seepage resistance and so on. With the continuous optimization and quality control improvement, ISIT has overcome many problems, such as downhole short circuit and communication loss, and is becoming more stable and reliable. At present, ISIT can meet the needs of large flow injection(max 800m3/d per layer) and can adapt to the high frequency of acidizing and fracturing in offshore oilfield. The failure rate of ISIT has dropped to nearly 20% in 2020. As of December 2020, ISIT has formed series products for different internal diameter wells and applied in 156 water injection wells in B offshore oilfield. The average allocation frequency has increased from less than one time to 2 times per year. Through the application of ISIT, B offshore oilfield has accumulatively saved more than 2100 days of platform occupation and more than 73 million RMB yuan of allocation cost. The use of ISIT makes B offshore oilfield's injection become more efficient and intelligent. The 5 years’ experience of ISIT applicationin B offshore oilfield has a fairly referential significance for other offshore oilfields.


Author(s):  
Maher A. El-Masri

Intercooled/Recuperated gas turbine systems provide high-efficiency and power density for naval propulsion. Current aero-derivative systems are capable of about 43% thermal efficiency in this configuration. With continued progress in gas-turbine materials and cooling technology, the possibility of further improving system performance by incorporation of gas-turbine reheat arises. A preliminary scan of this class of cycles is presented and compared with non-reheat intercooled/recuperated cycles at two levels of component technology. For conservative component technology, the reheat is found to provide very modest performance advantages. With advanced components and ceramic thermal barrier coatings, the reheat is found to offer potential for specific power improvements of up to 33% and for modest efficiency gains, on the order of one percentage point, while enabling turbine inlet temperatures well below those for the most efficient non-reheat cycles. The high-performance reheat systems, however, require reheat-combustor inlet temperatures beyond current practice. The use of water-injection in the intercooler, together with an aftercooler and a water-injected evaporative-recuperator is found to produce very large gains in efficiency as well as specific power. This modification may be feasible for land-based systems, where it can compete favourably with combined cycles. Despite the difficulty of obtaining pure water for a shipboard propulsion system, those large gains may justify further studies of this system and of means to provide its water supply in marine applications.


2016 ◽  
Author(s):  
Sun Fuchao ◽  
Jia Deli ◽  
Yu Jiaqing ◽  
Pei Xiaohan ◽  
Liu He ◽  
...  

2013 ◽  
Vol 734-737 ◽  
pp. 1354-1357
Author(s):  
Wu Yi Shan ◽  
Wei Lin Cui ◽  
Yong Sheng Li

The separate layer water injection rate determines the result of water injection. In the past, in order to inject a proper amount of water into different intervals, most of the time people would rely on their experiences. By employing this method, the amount of work was enormous and the result was not necessarily accurate. In this paper, five factors that would affect the water injection rate are taken into consideration, such as, thickness of the main well, the connected thickness, permeability, number of connected wells and oil saturation. A method of determining the proper water injection rate of single wells based on analytic hierarchy process is proposed. This method has been proven to be simple and accurate, the test result of a mathematical model also shows it fits the requirements of the oil field exploitation with current water cut and it is of great value to practical applications.


Sign in / Sign up

Export Citation Format

Share Document