scholarly journals Integrated Subsurface Analysis of Thickness and Density for Liquefaction Hazard: Case Study of South Cilacap Region, Indonesia.

Author(s):  
Maulana Rizki Aditama ◽  
Huzaely Latief Sunan ◽  
FX Anjar Tri Laksono ◽  
Gumilar Ramadhan ◽  
Sachrul Iswahyudi ◽  
...  

The thickness of the liquefable layer can be the factor inducing liquefaction hazard, apart from seismicity. Several studies have been conducted to predict the possibility of the liquefable layer based on the filed sampling. However, a detailed investigation of the subsurface interpretation has not been defined, in particular the thickness estimation of the liquefable layer. This study is carried out in south Cilacap area where potential liquefaction is exists due to the earthquake history data and near surface condition. The aim of this study is to investigate the physical properties and thickness distribution using GGMplus gravity data and resistivity data. This research is conducted by spectrum analysis of gravity model and 2D resistivity model . This study’s main results is by performing the residual gravity anomaly with the associated SRTM/DEM data to define the subsurface physical distribution and structural orientation of the area. Residual gravity anomaly is also separated through the low pass filter in order to have robust interpretation. The residual anomaly indicates that the area has identical structural pattern with geological and SRTM map. The results show a pattern of high gravity index in the northeast area of ​​the study having range of 70 – 115 MGal gravity index, associated with the volcanic breccia, and a low gravity profile with less than 65 in the southwest, associated with the alluvial and water table dominated distribution. The thickness of Alluvial is determined by resistivity model with H1 at a range of 3 meters and H2 at a range of 4 m. This research is included in the potential liquefaction category with the potential for a large earthquake.

2020 ◽  
Vol 25 (4) ◽  
pp. 463-476
Author(s):  
Ata Eshaghzadeh ◽  
Alireza Hajian

This paper presents an improved nature-based algorithm, namely multivariable modified teaching learning based optimization (MM-TLBO) algorithm, as in an iterative process can estimates the best values for the model parameters in a multi-objective problem. The algorithm works in two computational phases: the teacher phase and the learner phase. The major purpose of the MM-TLBO algorithm is to improve the value of the learners and thus, improving the value of the model parameters which leads to the optimal solution. The variables of each learner (model) are the radius ( R), depth ( h), shape factor ( q), density contrast ( ρ) and axis location ( x0) parameters. We apply MM-TLBO and TLBO methods for the residual gravity anomalies caused by the buried masses with a simple geometry such as spheres, horizontal and vertical cylinders. The efficiency of these methods are also tested by noise corruption synthetic data, as the acceptable results were obtained. The obtained results indicate the better performance the MM-TLBO algorithm than the TLBO algorithm. We have utilized the MM-TLBO for the interpretation of the six residual gravity anomaly profiles from Iran, USA, Sweden and Senegal. The advantage of the MM-TLBO inversion is that it can estimates the best solutions very fast without falling into local minimum and reaches to a premature convergence. The considered primary population for the synthetic and real gravity data are thirty and fifty models. The results show which this method is able to achieve the optimal responses even if a small population of learners had been considered.


Geophysics ◽  
1990 ◽  
Vol 55 (3) ◽  
pp. 376-377 ◽  
Author(s):  
El‐Sayed M. Abdelrahman

In the article by Gupta, the problem of depth determination of a buried structure from the residual gravity anomaly has been transformed into a problem of finding the solution of a nonlinear equation of the form f(z) = 0. Gupta begins his formulation of the problem with equation (1) from Mettleton (1942) Eq. (1) [Formula: see text]


Geophysics ◽  
2013 ◽  
Vol 78 (5) ◽  
pp. G89-G101 ◽  
Author(s):  
Ahmed Salem ◽  
Chris Green ◽  
Simon Campbell ◽  
J. Derek Fairhead ◽  
Lorenzo Cascone ◽  
...  

We sought to map the depth and density contrast of the Mohorovičić discontinuity (Moho) across the Red Sea area and to model sedimentary thickness from gravity data. The gravity data that are used are a combination of satellite and terrestrial gravity data processed into a Bouguer anomaly grid. A 200-km low-pass filter was used to separate this grid into regional and residual gravity grids. We inverted the regional gravity grid to a Moho depth map based on a density contrast map that is constrained by published seismic results. The interpreted Moho is shallowest ([Formula: see text]) along the axis of the central Red Sea, [Formula: see text] along the axis to the south, and [Formula: see text] in the northern Red Sea. The depth increased to [Formula: see text] at the coast and 35–40 km in the adjacent continents. The residual gravity data provided insights into the tectonic fabric along the whole rift and provided a good correlation with magnetic lineaments where these are available. We used the complete Bouguer anomaly to model sedimentary thicknesses constrained by wells and the interpreted Moho. The modeling results are consistent with the presence of large-scale, ridge parallel tilted fault blocks forming subbasins with a maximum depth of about 6–7 km. Our models suggest that the northern Red Sea has an asymmetric basement surface with the western side deeper than the eastern side. The results indicate the presence of oceanic crust in the central and southern parts of the Red Sea, but not in the north. The very thin crust and interpreted oceanic crustal density in the central Red Sea suggest that this area is fully oceanic—although possibly quite young.


2019 ◽  
Vol 37 (2) ◽  
Author(s):  
Gilberto Carneiro dos Santos Junior ◽  
Cristiano Mendel Martins ◽  
Nelson Ribeiro-Filho

ABSTRACT. Dealing with gravity data at complex geological environments is a hard task because regional and residual anomalies are unknown. Due to the fact former techniques do not apply geologic information for separating gravity data, interpretation could lead to common mistakes. In order to allow a better interpretation at sedimentary basins, we applied a different approach for separating regional and residual anomalies for gravity data: the crustal modeling procedure. This approach consists on discretizing the Earth’s crust in prismatic cells and calculating the predicted signal due to Earth’s crust. We set horizontal dimensions of each prism, while the top and bottom are defined by Earth’s topography and depth of crust-mantle boundary, usually called Moho. Additionally, when the predicted signal is calculated, the residual anomaly is obtained from simple subtraction. We applied our methodology at Marajó basin (North, Brazil), where previous geological studies identified a system of faults and grabens, also known as Marajó graben system. Moreover, our results are well compared with previous interpretation through the seismic method, exemplifying the approach’s quality and efficiency. We believe, therefore, that the crustal modeling approach should be considered for studying any Brazilian sedimentary basin and other interesting areas.Keywords: crustal modeling; residual gravity anomaly; Marajó basin; Marajó graben system. RESUMO. Interpretar dados gravimétricos em ambientes geológicos de grande complexidade é uma tarefa difícil de ser realizada, visto que anomalias regionais e residuais são desconhecidas. Devido ao fato de que conhecidas técnicas de separação regional-residual não consideram informações geológicas, a interpretação final pode fornecer resultados equivocados. A fim de permitir uma melhor interpretação nas bacias sedimentares, aplicamos uma diferente abordagem para separação regional-residual: a modelagem crustal. Esta abordagem consiste em discretizar a crosta terrestre em células prismáticas e calcular o sinal regional predito. Definimos as dimensões horizontais de cada prisma, enquanto o topo e a base são definidos pela topografia e profundidade da interface crosta-manto, respectivamente. Após o cálculo do sinal predito, a anomalia residual é calculada via subtração. Aplicamos nossa metodologia na bacia do Marajó (região Norte, Brasil), onde estudos geológicos identificaram um sistema de falhas e grábens, definido por sistema de gráben do Marajó. Nossos resultados apresentam boa correspondência quando comparados com interpretações realizadas via método sísmico, o que exemplifica a qualidade e eficiência da nossa proposta. Acreditamos, portanto, que esta abordagem de modelagem crustal deve ser considerada para o estudo de qualquer bacia sedimentar brasileira e de outras regiões de interesse.Palavras-chave: modelagem crustal; anomalia gravimétrica residual; bacia do Marajó; sistema de gráben do Marajó.  


Geophysics ◽  
1995 ◽  
Vol 60 (2) ◽  
pp. 589-590 ◽  
Author(s):  
El‐Sayed M. Abdelrahman ◽  
Sharafeldin M. Sharafeldin

The gravity anomaly expression produced by most geologic structures can be represented by a continuous function of both shape (shape‐factor) and depth‐related variables with an amplitude coefficient related to mass (Abdelrahman and El‐Araby, 1993). Few methods have been developed to determine the shape of the buried geologic structure from residual gravity anomaly profiles. These methods include a Walsh transform approach (Shaw and Agarwal, 1990) and the employment of a correlation factor between successive least‐squares residuals (Abdelrahman and El‐Araby 1993). In the present note, a least‐squares minimization approach to shape‐factor determination from a residual gravity anomaly profile is presented. The problem of the shape‐factor determination is transformed into the problem of finding a solution of a nonlinear equation of the form f(q) = 0.


Geophysics ◽  
2017 ◽  
Vol 82 (3) ◽  
pp. G45-G55 ◽  
Author(s):  
Juan García-Abdeslem

The flexural isostatic response to surface loads is used to estimate the crustal thickness in northwestern Mexico and Southwestern USA. This estimate is used to compute an isostatic regional gravity, which, subtracted from Bouguer gravity anomalies, led to the isostatic residual gravity anomaly at Montage Basin. This basin is located between the southern portion of the Mexicali Valley and the northern Gulf of California, it roughly has an extension of [Formula: see text] wide, and it shows a gravity minimum reaching approximately [Formula: see text]. Montage Basin is within the extensional province of the Gulf of California, where rifting is currently an ongoing geologic process, and deep exploratory wells drilled by Petróleos Mexicanos have shown that the basin accommodates thick sedimentary sequences greater than 5 km. The interpretation of the isostatic residual gravity anomaly is considered as a nonlinear inverse problem, constrained using density as a function of depth derived from Gardner’s equation applied to dual time [Formula: see text]-logs, assuming isostatic equilibrium and considering the basin as a subsurface load that is compensated at depth by a mass of unknown shape and density. The outcome of the inverse problem suggests that Montage Basin accommodates as much as 7.5 km thick sedimentary sequences and a compensating mass at a minimum depth of 13 km.


1967 ◽  
Vol 104 (1) ◽  
pp. 63-72 ◽  
Author(s):  
Hamid Nassar Al-Sadi

AbstractThe area to the north of Barnstaple (North Devon) was covered by a detailed gravity survey. The main gravity gradient of the Bouguer anomaly map (estimated to be 1·2 mgals per mile) confirmed the conclusions drawn by Bott et al. (1958), who attributed it to a basin of possibly Carboniferous sediments and/or Old Red Sandstone, about 4 miles thick, separated from the outcropping Devonian rocks by an assumed thrust plane.A negative residual gravity anomaly is located over the outcrop of the Pickwell Down Sandstone. Analyses of the anomaly show that it is caused by the southwards dipping belt of sandstone and that the angle of dip of the formation decreases with depth. At a depth of about 2 miles the formation becomes nearly horizontal. Alternatively, it may terminate against an assumed thrust plane underlying the whole outcropping Devonian.The aeromagnetic map of the area shows an elongated magnetic “high” following the outcrop of the Morte Slates. The anomaly is probably caused by near surface, highly magnetized rocks in association with the Morte Slates.


Sign in / Sign up

Export Citation Format

Share Document