Computer modeling of nitrogen redistribution in technologies of complex ion nitriding of alloy steels

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Download Full-text

EELS characterization of “Smut” layer films on steel surface prepared for chrome plating by anodic etching

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100139068 ◽

1995 ◽

Vol 53 ◽

pp. 538-539

Author(s):

E Y. Wang ◽

J. T. Cherian ◽

A. Madsen ◽

R. M. Fisher

Keyword(s):

Steel Surface ◽

Surface Preparation ◽

Treatment Method ◽

Chrome Plating ◽

Transmission Electron ◽

Alloy Steels ◽

Pre Treatment ◽

Hard Chrome ◽

Electron Energy Loss

Many steel parts are electro-plated with chromium to protect them against corrosion and to improve their wear-resistance. Good adhesion of the chrome plate to the steel surface, which is essential for long term durability of the part, is extremely dependent on surface preparation prior to plating. Recently, McDonnell Douglas developed a new pre-treatment method for chrome plating in which the steel is anodically etched in a sulfuric acid and hydrofluoric acid solution. On carbon steel surfaces, this anodic pre-treatment produces a dark, loosely adhering material that is commonly called the “smut” layer. On stainless steels and nickel alloys, the surface is only darkened by the anodic pre-treatment and little residue is produced. Anodic pre-treatment prior to hard chrome plating results in much better adherence to both carbon and alloy steels.We have characterized the anodic pre-treated steel surface and the resulting “smut” layer using various techniques including electron spectroscopy for chemical analysis (ESCA) on bulk samples and transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS) on stripped films.

Download Full-text

Computer modeling of the mitral valve for planning of complex repairs

The Thoracic and Cardiovascular Surgeon ◽

10.1055/s-0032-1332693 ◽

2013 ◽

Vol 61 (S 01) ◽

Author(s):

CJ Beller ◽

I Baxter ◽

K Kallenbach ◽

T Mesana ◽

M Labrosse

Keyword(s):

Mitral Valve ◽

Computer Modeling

Download Full-text

Computer Modeling-Assisted Design And Synthesis Of Flavonols Derivatives As Proteasome Inhibitors

Planta Medica ◽

10.1055/s-0036-1578757 ◽

2016 ◽

Vol 82 (05) ◽

Author(s):

KY Orabi ◽

MS Abaza ◽

KA ElSayed ◽

AY Elnagar ◽

SI Faggal ◽

...

Keyword(s):

Computer Modeling ◽

Proteasome Inhibitors ◽

Design And Synthesis

Download Full-text

The Role of Computer Modeling in Electrocardiography

Methods of Information in Medicine ◽

10.1055/s-0038-1634809 ◽

1990 ◽

Vol 29 (04) ◽

pp. 282-288 ◽

Cited By ~ 2

Author(s):

A. van Oosterom

Keyword(s):

Electrical Activity ◽

Computer Modeling ◽

Body Surface ◽

Electrical Current ◽

The Body ◽

Volume Conductor ◽

Current Generator ◽

Cardiac Electrical Activity ◽

Source Models

AbstractThis paper introduces some levels at which the computer has been incorporated in the research into the basis of electrocardiography. The emphasis lies on the modeling of the heart as an electrical current generator and of the properties of the body as a volume conductor, both playing a major role in the shaping of the electrocardiographic waveforms recorded at the body surface. It is claimed that the Forward-Problem of electrocardiography is no longer a problem. Several source models of cardiac electrical activity are considered, one of which can be directly interpreted in terms of the underlying electrophysiology (the depolarization sequence of the ventricles). The importance of using tailored rather than textbook geometry in inverse procedures is stressed.

Download Full-text