scholarly journals Second-generation composites from recycled wind turbine blades

2019 ◽  
Author(s):  
Azadeh Tavousi Tabatabaei ◽  
Seyed Hossein Mamanpush
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Second Generation ◽  
Turbine Blades ◽  
Clean Energy ◽  
Wind Turbine Blades ◽  
Environmental Attributes ◽  
The Us ◽  
The World

The demand for wind and other forms of clean energy is increasing in the US and throughout the world. Wind energy is also expected to provide 14.9% of the global electricity demand by 2020. Under this scenario, a significant amount of wind turbine blades (WTBs) will continue to burden our current landfills until a viable recycling strategy is found. Repurposing or recycling of end- of-use wind turbine blade material will provide both economic and environmental attributes.

Seagull in Wind Turbine Airfoil Blade Design Application Bionic

2013 ◽  
Vol 380-384 ◽  
pp. 4336-4339
Author(s):  
Hua Xin ◽  
Chun Hua Zhang ◽  
Qing Guo Zhang ◽  
Ping Wang
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Simulation Analysis ◽  
Turbine Blades ◽  
Clean Energy ◽  
Aerodynamic Performance ◽  
Blade Design ◽  
Wind Turbine Blades ◽  
Bionic Blade ◽  
Turbine Blade Design

Wind energy is an inexhaustible, an inexhaustible source of renewable and clean energy. Present due to the energy crisis and environmental protection and other issues, the use of wind more and more world attention. The wind turbine is the best form of wind energy conversion. Wind turbine wind turbine blades to capture wind energy is the core component of the blade in a natural environment to run directly in contact with air, with seagulls wings generate lift conditions are similar, so the gull wings airfoil and excellent conformation, with wind turbine blade design designed by combining the bionic blades. Through numerical simulation analysis found bionic blade aerodynamic performance than the standard blade aerodynamic performance has improved.

scholarly journals The strategy of simulation effects of wind speed, variation of turbine blades and it’s interaction to power generated by vertical axis wind turbine using NACA 2412

2017 ◽  
Vol 7 (1.2) ◽  
pp. 246
Author(s):  
Bambang Sugiyono Agus Purwono ◽  
Masroni . ◽  
Awan Setiawan ◽  
Tundung Subali Patma ◽  
Ida Bagus Suardika
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Clean Energy ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Power Capacity ◽  
Speed Variation

The objective of this paper is to simulate the effects upon the wind speed, variation of turbine blades and interaction of wind speed and variation of turbine blades to the power capacity generated by Vertical Axis Wind Turbine (VAWT) using NACA 2412 and to stratify the power capacity generated by the VAWT simulation. The research backgrounds are the wind-energy potential in Indonesia is about 9.290 MW and has already elaborated by Ministry of Mining, and Energy Resources is about 50 MW. This wind energy is environmentally (clean energy), economically (cheapest), easy to operate and easy to maintain, also renewable energy. The method of analysis is quantitative approach using two way classification (analysis of variance or design of experiments). The research variables are wind speed, variation of turbine blades and this interaction among independent variables and the power capacity as dependent variables. Data wind speed simulation vary from 3 m/s till 6 m/s. The quantity of turbine blades vary from 3 till 8 units. The finding from this research is accepted the null hypothesis or not differ significantly at 5% from each independent variable. The scenario and the parameters during the strategy development use turbine blades, wind speed and power generated by VAWT and the maximum power generated is 16.38 watt. The wind speed is 6 m/s and the number of turbine blade is 4 units. However, the minimum power generated by VAWT is 0.45 watt, the wind speed is 6 m/s and the number of turbine blade is 3 units.

Machine Learning Aided Prediction of Rain Erosion Damage on Wind Turbine Blade Sections

2021 ◽  
Author(s):  
Alessio Castorrini ◽  
Paolo Venturini ◽  
Fabrizio Gerboni ◽  
Alessandro Corsini ◽  
Franco Rispoli
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Energy Production ◽  
Turbine Blades ◽  
Wind Farms ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Coating Materials ◽  
Erosion Modelling ◽  
Rain Erosion

Abstract Rain erosion of wind turbine blades represents an interesting topic of study due to its non-negligible impact on annual energy production of the wind farms installed in rainy sites. A considerable amount of recent research works has been oriented to this subject, proposing rain erosion modelling, performance losses prediction, structural issues studies, etc. This work aims to present a new method to predict the damage on a wind turbine blade. The method is applied here to study the effect of different rain conditions and blade coating materials, on the damage produced by the rain over a representative section of a reference 5MW turbine blade operating in normal turbulence wind conditions.

Design and Analysis of Wind Turbine Blades: Winglet, Tubercle, and Slotted

2013 ◽  
Author(s):  
Alka Gupta ◽  
Abdulrahman Alsultan ◽  
R. S. Amano ◽  
Sourabh Kumar ◽  
Andrew D. Welsh
Keyword(s):  
Power Generation ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Alternative Energy ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Wind Speeds ◽  
Governing Factor

Energy is the heart of today’s civilization and the demand seems to be increasing with our growing population. Alternative energy solutions are the future of energy, whereas the fossil-based fuels are finite and deemed to become extinct. The design of the wind turbine blade is the main governing factor that affects power generation from the wind turbine. Different airfoils, angle of twist and blade dimensions are the parameters that control the efficiency of the wind turbine. This study is aimed at investigating the aerodynamic performance of the wind turbine blade. In the present paper, we discuss innovative blade designs using the NACA 4412 airfoil, comparing them with a straight swept blade. The wake region was measured in the lab with a straight blade. All the results with different designs of blades were compared for their performance. A complete three-dimensional computational analysis was carried out to compare the power generation in each case for different wind speeds. It was found from the numerical analysis that the slotted blade yielded the most power generation among the other blade designs.

Research on Wind Turbine Blade Loads and Dynamics Factors

2014 ◽  
Vol 1014 ◽  
pp. 124-127
Author(s):  
Zhi Qiang Xu ◽  
Jian Huang
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Wind Turbines ◽  
Mechanical Energy ◽  
Turbine Blades ◽  
Electrical Energy ◽  
Wind Turbine Blade ◽  
Strength Analysis ◽  
Wind Turbine Blades ◽  
Turbine Wheel

Wind turbines consists of three key parts, namely, wind wheels (including blades, hub, etc.), cabin (including gearboxes, motors, controls, etc.) and the tower and Foundation. Wind turbine wheel is the most important part ,which is made up of blades and hubs. Blade has a good aerodynamic shape, which will produce aerodynamic in the airflow rotation, converting wind energy into mechanical energy, and then, driving the generator into electrical energy by gearbox pace. Wind turbine operates in the natural environment, their load wind turbine blades are more complex. Therefore load calculations and strength analysis for wind turbine design is very important. Wind turbine blades are core components of wind turbines, so understanding of their loads and dynamics by which the load on the wind turbine blade design is of great significance.

scholarly journals Preparation and Anti-Icing of Hydrophobic Polypyrrole Coatings on Wind Turbine Blade

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Bin Qu ◽  
Zhou Sun ◽  
Fang Feng ◽  
Yan Li ◽  
Guoqiang Tong ◽  
...  
Keyword(s):  
Contact Angle ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Water Contact Angle ◽  
Turbine Blades ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Water Contact

This paper describes the method of preparing strong hydrophobic polypyrrole (PPy) on wind turbine blades. The water contact angle of strong hydrophobic PPy coatings was 127.2°. The strong hydrophobic PPy coatings exhibited excellent anti-icing properties. The maximum icing weight of strong hydrophobic PPy coating blade was almost 0.10 g while the maximum icing weight of no coating blade was found to be 26.13 g. The maximum icing thickness of a strong hydrophobic PPy coating blade was only 1.08 mm. The current research will provide a better technique to create anti-icing coatings on wind turbine blades and other outdoor equipment.

scholarly journals Bionic Design of Wind Turbine Blade Based on Long-Eared Owl’s Airfoil

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Weijun Tian ◽  
Zhen Yang ◽  
Qi Zhang ◽  
Jiyue Wang ◽  
Ming Li ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Lower Surface ◽  
Aerodynamic Characteristics ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Bionic Design ◽  
Bionic Blade

The main purpose of this paper is to demonstrate a bionic design for the airfoil of wind turbines inspired by the morphology of Long-eared Owl’s wings. Glauert Model was adopted to design the standard blade and the bionic blade, respectively. Numerical analysis method was utilized to study the aerodynamic characteristics of the airfoils as well as the blades. Results show that the bionic airfoil inspired by the airfoil at the 50% aspect ratio of the Long-eared Owl’s wing gives rise to a superior lift coefficient and stalling performance and thus can be beneficial to improving the performance of the wind turbine blade. Also, the efficiency of the bionic blade in wind turbine blades tests increases by 12% or above (up to 44%) compared to that of the standard blade. The reason lies in the bigger pressure difference between the upper and lower surface which can provide stronger lift.

scholarly journals Aerodynamic Analysis on Wind Turbine Aerofoil

2018 ◽  
Vol 7 (3.27) ◽  
pp. 456
Author(s):  
Albi . ◽  
M Dev Anand ◽  
G M. Joselin Herbert
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Ansys Fluent ◽  
Wind Speeds ◽  
Drag Forces ◽  
Lift And Drag

The aerofoils of wind turbine blades have crucial influence on aerodynamic efficiency of wind turbine. There are numerous amounts of research being performed on aerofoils of wind turbines. Initially, I have done a brief literature survey on wind turbine aerofoil. This project involves the selection of a suitable aerofoil section for the proposed wind turbine blade. A comprehensive study of the aerofoil behaviour is implemented using 2D modelling. NACA 4412 aerofoil profile is considered for analysis of wind turbine blade. Geometry of this aerofoil is created using GAMBIT and CFD analysis is carried out using ANSYS FLUENT. Lift and Drag forces along with the angle of attack are the important parameters in a wind turbine system. These parameters decide the efficiency of the wind turbine. The lift force and drag force acting on aerofoil were determined with various angles of attacks ranging from 0° to 12° and wind speeds. The coefficient of lift and drag values are calculated for 1×105 Reynolds number. The pressure distributions as well as coefficient of lift to coefficient of drag ratio of this aerofoil were visualized. The CFD simulation results show close agreement with those of the experiments, thus suggesting a reliable alternative to experimental method in determining drag and lift.

scholarly journals Design for Recycling Principles Applicable to Selected Clean Energy Technologies: Crystalline-Silicon Photovoltaic Modules, Electric Vehicle Batteries, and Wind Turbine Blades

2020 ◽  
Vol 6 (4) ◽  
pp. 761-774
Author(s):  
Alex Norgren ◽  
Alberta Carpenter ◽  
Garvin Heath
Keyword(s):  
Wind Turbine ◽  
Crystalline Silicon ◽  
Raw Materials ◽  
Turbine Blades ◽  
Lithium Ion ◽  
Clean Energy ◽  
Raw Material ◽  
Wind Turbine Blades ◽  
Design For Recycling ◽  
Pv Modules

Abstract The global growth of clean energy technology deployment will be followed by parallel growth in end-of-life (EOL) products, bringing both challenges and opportunities. Cumulatively, by 2050, estimates project 78 million tonnes of raw materials embodied in the mass of EOL photovoltaic (PV) modules, 12 billion tonnes of wind turbine blades, and by 2030, 11 million tonnes of lithium-ion batteries. Owing partly to concern that the projected growth of these technologies could become constrained by raw material availability, processes for recycling them at EOL continue to be developed. However, none of these technologies are typically designed with recycling in mind, and all of them present challenges to efficient recycling. This article synthesizes and extends design for recycling (DfR) principles based on a review of published industrial and academic best practices as well as consultation with experts in the field. Specific principles developed herein apply to crystalline-silicon PV modules, batteries like those used in electric vehicles, and wind turbine blades, while a set of broader principles applies to all three of these technologies and potentially others. These principles are meant to be useful for stakeholders—such as research and development managers, analysts, and policymakers—in informing and promoting decisions that facilitate DfR and, ultimately, increase recycling rates as a way to enhance the circularity of the clean energy economy. The article also discusses some commercial implications of DfR. Graphical Abstract

Dynamic behaviour of wind turbine blades

2008 ◽  
Vol 222 (8) ◽  
pp. 1453-1464 ◽  
Author(s):  
Ming-Hung Hsu
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Dynamic Behaviour ◽  
Differential Quadrature Method ◽  
Turbine Blades ◽  
Differential Quadrature ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Discrete Eigenvalue ◽  
Euler Bernoulli Beam

Wind power does not generate pollution and is a clean source. The dynamic problems associated with wind turbine blades are formulated using the differential quadrature method. The Euler—Bernoulli beam paradigm is used to characterize wind turbine blades. The differential quadrature technique is utilized to transform partial differential equations, which presents the dynamic behaviour of wind turbine blades, into a discrete eigenvalue problem. The effects of the number of sample points on the accuracy of the calculated natural frequencies are studied. Numerical results show that the rotational speed impacts significantly the first frequency of the wind turbine blade. The pitch angle could not markedly affect wind turbine blade frequencies.

Sign in / Sign up

Export Citation Format

Share Document