scholarly journals Acid Blue 25 Removal by using Electro-Persulfate Process

2020 ◽  
Author(s):  
Zeinab Ghorbani
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Salt Concentration ◽  
Dye Removal ◽  
Industrial Effluents ◽  
Sodium Persulfate ◽  
Initial Concentration ◽  
Acid Blue 25 ◽  
Sulfate Process ◽  
Acid Blue

This study aimed to investigate the efficiency of the electro-persulfate process in removing acid blue 25 from aqueous solution. In order to optimize the parameters, the OFAT method was used, and the effect of three main parameters, including pH, sodium persulfate salt concentration, and current intensity was investigated. According to the results, the optimal removal efficiency of 94% in 60 minutes was obtained under conditions of pH=5, the initial concentration of sodium persulfate=250 mg / L, and the current=500 mA. According to the results of this study, the electro-persulfate process sulfate process can be an efficient process for dye removal from industrial effluents.

scholarly journals Performance Comparison of Fe2+ Activated Persulfate and Electro-Persulfate Process in Acid Blue 25 Removal from Aqueous Solution Operating: Conditions and Reaction Velocity

2020 ◽  
Author(s):  
Zeinab Ghorbani
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Ferrous Sulfate ◽  
Electrochemical Process ◽  
Sodium Persulfate ◽  
Sulfate Concentration ◽  
Reaction Velocity ◽  
Acid Blue 25 ◽  
Acid Blue ◽  
Activated Persulfate

The purpose of this study was to compare the performance of Fe2+ activated persulfate and electro-persulfate process in Acid Blue 25 removal from aqueous solution. For this reason, the effects of different parameters including pH, dye, sodium persulfate and ferrous sulfate concentrations were investigated. The removal efficiency of 92% at the time of 60 min was obtained at pH= 3, dye concentration= 50 mg/L, sodium persulfate concentration= 500 mg/L and Fe (II) sulfate concentration= 100 mg/L for Fe2+ activated persulfate system and the removal efficiency of 95% at pH= 5, dye concentration = 200 mg/L, sodium persulfate concentration = 500 mg/L and ferrous sulfate concentration = 100 mg/L for electro-persulfate system by means of graphite materials as the neutral electrodes. COD removal efficiency in Fe2+ activated persulfate and electro-persulfate in the mentioned conditions were 90% and 89% in 180 minutes, respectively. Moreover, the result of process kinetics showed that using electrochemical process improved the reaction velocity from 0.0016 to 0.0487 mg/L/min. The comparison between these two-process showed that using electrochemical process improved dye removal efficiency by 4 times.

scholarly journals Acid Blue 25 Removal by using Fe2+ Activated Persulfate

2020 ◽  
Author(s):  
Zeinab Ghorbani
Keyword(s):  
Textile Industry ◽  
Dye Removal ◽  
Aqueous Media ◽  
Industrial Effluents ◽  
Sodium Persulfate ◽  
Optimal Conditions ◽  
Initial Concentration ◽  
The One ◽  
Acid Blue ◽  
Activated Persulfate

Dyes are one of the most important contaminants in the textile industry wastewater, which are often carcinogenic, and biodegradable. So their removal from the effluent is environmentally important. This study aimed to investigate the efficiency of sodium persulfate in removing dye from aqueous media. In order to optimize each parameter, the one-factor-at-a-time method was used. In this experimental study, the effect of three main parameters including pH, sodium persulfate concentration, and iron (II) concentration on dye removal from aqueous solution was investigated. According to the results obtained from the experiments, the optimal removal efficiency of 92% was obtained in 60 minutes and under optimal conditions of pH=3, the initial concentration of sodium persulfate=500 mg / L, and the initial concentration of iron (II) sulfate=100 mg / L. According to the results, the use of sodium persulfate salt activated with Fe2+ can be an efficient process for dye removal from industrial effluents.

Shrimp shell as an efficient bioadsorbent for Acid Blue 25 dye removal from aqueous solution

2014 ◽  
Vol 45 (6) ◽  
pp. 2926-2934 ◽  
Author(s):  
Ehsan Daneshvar ◽  
Mohammad Salar Sohrabi ◽  
Masoud Kousha ◽  
Amit Bhatnagar ◽  
Bahar Aliakbarian ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Dye Removal ◽  
Shrimp Shell ◽  
Acid Blue 25 ◽  
Acid Blue

Comparative Bio-sorption of Cadmium and Nickel Ions from Aqueous Solution onto Fibers of Date Palm using Fluidized Bed Column

2019 ◽  
Vol 70 (5) ◽  
pp. 1507-1512
Author(s):  
Baker M. Abod ◽  
Ramy Mohamed Jebir Al-Alawy ◽  
Firas Hashim Kamar ◽  
Gheorghe Nechifor
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Metal Ions ◽  
Fluidized Bed ◽  
Removal Efficiency ◽  
Heavy Metal Ions ◽  
Date Palm ◽  
Operating Conditions ◽  
Initial Concentration ◽  
Bed Height

The aim of this study is to use the dry fibers of date palm as low-cost biosorbent for the removal of Cd(II), and Ni(II) ions from aqueous solution by fluidized bed column. The effects of many operating conditions such as superficial velocity, static bed height, and initial concentration on the removal efficiency of metal ions were investigated. FTIR analyses clarified that hydroxyl, amine and carboxyl groups could be very effective for bio-sorption of these heavy metal ions. SEM images showed that dry fibers of date palm have a high porosity and that metal ions can be trapped and sorbed into pores. The results show that a bed height of 6 cm, velocity of 1.1Umf and initial concentration for each heavy metal ions of 50 mg/L are most feasible and give high removal efficiency. The fluidized bed reactor was modeled using ideal plug flow and this model was solved numerically by utilizing the MATLAB software for fitting the measured breakthrough results. The breakthrough curves for metal ions gave the order of bio-sorption capacity as follow: Cd(II)]Ni(II).

scholarly journals Removal of Methylene Blue and Congo Red Using Adsorptive Membrane Impregnated with Dried Ulva fasciata and Sargassum dentifolium

Plants ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 384
Author(s):  
Ahmed Labena ◽  
Ahmed E. Abdelhamid ◽  
Abeer S. Amin ◽  
Shimaa Husien ◽  
Liqaa Hamid ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Removal Efficiency ◽  
Congo Red ◽  
Dye Removal ◽  
Industrial Effluents ◽  
Composite Membranes ◽  
Acrylic Fiber ◽  
Ulva Fasciata ◽  
Ft Ir ◽  
Sorption Time

Biosorption is a bioremediation approach for the removal of harmful dyes from industrial effluents using biological materials. This study investigated Methylene blue (M. blue) and Congo red (C. red) biosorption from model aqueous solutions by two marine macro-algae, Ulva fasciata and Sargassum dentifolium, incorporated within acrylic fiber waste to form composite membranes, Acrylic fiber-U. fasciata (AF-U) and Acrylic fiber-S. dentifolium (AF-S), respectively. The adsorption process was designed to more easily achieve the 3R process, i.e., removal, recovery, and reuse. The process of optimization was implemented through one factor at a time (OFAT) experiments, followed by a factorial design experiment to achieve the highest dye removal efficiency. Furthermore, isotherm and kinetics studies were undertaken to determine the reaction nature. FT-IR and SEM analyses were performed to investigate the properties of the membrane. The AF-U membrane showed a significant dye removal efficiency, of 88.9% for 100 ppm M. blue conc. and 79.6% for 50 ppm C. red conc. after 240 min sorption time. AF-S recorded a sorption capacity of 82.1% for 100 ppm M. blue conc. after 30 min sorption time and 85% for 100 ppm C. red conc. after 240 min contact time. The membranes were successfully applied in the 3Rs process, in which it was found that the membranes could be used for five cycles of the removal process with stable efficiency.

scholarly journals Evaluation of removal efficiency of residual diclofenac in aqueous solution by nanocomposite tungsten-carbon using design of experiment

2017 ◽  
Vol 76 (6) ◽  
pp. 1466-1473 ◽  
Author(s):  
M. H. Salmani ◽  
M. Mokhtari ◽  
Z. Raeisi ◽  
M. H. Ehrampoush ◽  
H. A. Sadeghian
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Design Of Experiment ◽  
High Efficiency ◽  
Carbon Powder ◽  
Batch Adsorption ◽  
Effective Parameters ◽  
Initial Concentration ◽  
Carbon Nanocomposite ◽  
Maximum Removal

Wastewater containing pharmaceutical residual components must be treated before being discharged to the environment. This study was conducted to investigate the efficiency of tungsten-carbon nanocomposite in diclofenac removal using design of experiment (DOE). The 27 batch adsorption experiments were done by choosing three effective parameters (pH, adsorbent dose, and initial concentration) at three levels. The nanocomposite was prepared by tungsten oxide and activated carbon powder in a ratio of 1 to 4 mass. The remaining concentration of diclofenac was measured by a spectrometer with adding reagents of 2, 2′-bipyridine, and ferric chloride. Analysis of variance (ANOVA) was applied to determine the main and interaction effects. The equilibrium time for removal process was determined as 30 min. It was observed that the pH had the lowest influence on the removal efficiency of diclofenac. Nanocomposite gave a high removal at low concentration of 5.0 mg/L. The maximum removal for an initial concentration of 5.0 mg/L was 88.0% at contact time of 30 min. The results of ANOVA showed that adsorbent mass was among the most effective variables. Using DOE as an efficient method revealed that tungsten-carbon nanocomposite has high efficiency in the removal of residual diclofenac from the aqueous solution.

Spectrophotometric investigation of the interactions between cationic (C.I. Basic Blue 9) and anionic (C.I. Acid Blue 25) dyes in adsorption onto extracted cellulose from Posidonia oceanic in single and binary system

2016 ◽  
Vol 73 (9) ◽  
pp. 2211-2221 ◽  
Author(s):  
Najoua Ben Douissa ◽  
Sonia Dridi-Dhaouadi ◽  
Mohamed Farouk Mhenni
Keyword(s):  
Aqueous Solution ◽  
Molecular Complex ◽  
Photoelectron Spectroscopy ◽  
Electrostatic Interactions ◽  
Equilibrium Concentration ◽  
Species Interaction ◽  
Spectrophotometric Analysis ◽  
Textile Dye ◽  
Acid Blue 25 ◽  
Acid Blue

Extracted cellulose from Posidonia oceanica was used as an adsorbent for removal of a cationic (Basic blue 9, BB) and anionic textile dye (Acid blue 25, AB) from aqueous solution in single dye system. Characterization of the extracted cellulose and extracted cellulose-dye systems were performed using several techniques such as Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, zeta potential and Boehm acid–base titration method. Adsorption tests showed that the extracted cellulose presented higher adsorption of BB than AB in single dye system, revealing that electrostatic interactions are responsible, in the first instance, for the dye–adsorbent interaction. In single dye systems, the extracted cellulose presented the maximum adsorption capacities of BB and AB at 0.955 mmol.g−1 and 0.370 mmol.g−1, respectively. Adsorption experiments of AB dye on extracted cellulose saturated by BB dye exhibited the release of the latter dye from the sorbent which lead to dye–dye interaction in aqueous solution due to electrostatic attraction between both species. Interaction of BB and AB dyes were investigated using spectrophotometric analysis and results demonstrated the formation of a molecular complex detected at wavelengths 510 and 705 nm when anionic (AB) and cationic (BB) dye were taken in equimolar proportions. The adsorption isotherm of AB, taking into account the dye–dye interaction was investigated and showed that BB dye was released proportionately by AB equilibrium concentration. It was also observed that AB adsorption is widely enhanced when the formation of the molecular complex is disadvantaged.

scholarly journals Enhancement of the electro-activated persulfate process in dye removal using graphene oxide nanoparticle

2021 ◽  
Author(s):  
Bita Ayati ◽  
Zeinab Ghorbani
Keyword(s):  
Graphene Oxide ◽  
Current Density ◽  
Dye Removal ◽  
Electrochemical Process ◽  
Sodium Persulfate ◽  
Sulfate Concentration ◽  
Oxide Nanoparticle ◽  
Acid Blue ◽  
A Current ◽  
Activated Persulfate

Abstract This study aimed to improve the speed of the electrochemical process by graphene oxide nanoparticle as a current accelerator in Acid Blue 25 removal from aqueous solutions. To do so, the effect of different parameters including pH, dye concentration, sodium persulfate concentration, the ratio of sodium persulfate to iron (II) sulfate concentration, current density, and the distance between electrodes was investigated on dye removal. Under optimal conditions of pH = 5, dye concentration = 200 mg/L, sodium persulfate concentration = 500 mg/L, iron (II) sulfate concentration = 100 mg/L, current density = 16.67 mA/cm2, and electrode distance = 2 cm, 95% of dye was removed after 60 minutes in the electro-activated persulfate process; while the modified electro-activated persulfate process achieved 95% dye removal after only 40 minutes under the same conditions. This system was able to remove 90% of dye after 60 minutes at a higher concentration (300 mg/L). Also, the modified electro-activated persulfate process obtained the removal of 80% of COD, and 54% of TOC after 180 minutes in the mentioned conditions, for the dye concentration of 300 mg/L.

Sign in / Sign up

Export Citation Format

Share Document