scholarly journals Corrosion Inhibition of Bark Extract of Euphorbia royleana on Mild Steel in 1M HCl

2019 ◽  
Vol 40 ◽  
pp. 25-29
Author(s):  
Bishal Thapa ◽  
Dipak Kumar Gupta ◽  
Amar Prasad Yadav
Keyword(s):  
Weight Loss ◽  
Mild Steel ◽  
Corrosion Inhibitor ◽  
Inhibition Efficiency ◽  
Bark Extract ◽  
Potential Measurement ◽  
Maximum Inhibition ◽  
Weight Loss Method ◽  
Loss Method ◽  
Loss Experiment

The bark extract of Euphorbia royleana as a green corrosion inhibitor was studied in 1M HCl using weight-loss method and potential measurement. The results show that the bark extract of Euphorbia royleana is an effective anti-corrosion inhibitor of mild steel in acidic media. The corrosion rate decreases with the time of immersion. Weight loss experiment shows that the loss in weight decreases with the time of immersion and inhibition efficiency increases with the concentration of extract. It was observed that maximum inhibition efficiency is 99.60% in 100% concentration of extract. Potential measurement study shows that bark extracts act as a mixed type of inhibitor i.e. inhibits both anodically as well as cathodically. 

scholarly journals Effect of N-(6-aminobenzo[d]thiazol-2-yl)benzamide and 2,6-diamino-benzothiazole as Corrosion Inhibitor in acid medium

2016 ◽  
Vol 12 (12) ◽  
pp. 4593-4613
Author(s):  
Rekha. S ◽  
Kannan. K ◽  
Gnanavel. S
Keyword(s):  
Weight Loss ◽  
Mild Steel ◽  
Corrosion Inhibitor ◽  
Acid Medium ◽  
Potentiodynamic Polarization ◽  
Inhibition Efficiency ◽  
Free Energy Of Adsorption ◽  
Weight Loss Method ◽  
Ft Ir ◽  
Loss Method

2-amino-6-nitrobenzothiazole(ANBT) was used as an inhibitor for the corrosion of mild steel in acid medium since the inhibition efficiency was low for that compound, 2,6-diaminobenzothiazole (DABT) and N-(6-aminobenzo [d] thiazol-2-y1) benzamide(ABTB) was synthesized,  and characterized by FT-IR, H1NMR, and C13NMR.The synthesized compound was tested as a corrosion inhibitor for mild steel in 1N HCl solution using weight loss, Potentiodynamic polarization, and AC impedance techniques. The inhibition efficiency was studied at the different time, temperature and acid concentration by weight loss method. The values of activation energy and free energy of adsorption of these compounds were also calculated, which reveals that the inhibitor was adsorbed on the mild steel by physisorption mechanism. Adsorption obeys Langmuir and Temkin adsorption isotherms. The results obtained by weight loss method revealed that the compound performed as a better inhibitor for mild steel in 1N HCl. Potentiodynamic polarization studies showed that the inhibitor acts as a mixed type inhibitor.AC impedance studies revealed that the corrosion process was controlled by charge transfer process. Surface analysis was studied using SEM and FT-IR.

scholarly journals New Corrosion Inhibitor Derived from Coumarin

2017 ◽  
Author(s):  
Ahmed Al-Amiery
Keyword(s):  
Nuclear Magnetic Resonance ◽  
Weight Loss ◽  
Fourier Transform ◽  
Magnetic Resonance ◽  
Mild Steel ◽  
Corrosion Inhibitor ◽  
Damage Reduction ◽  
Weight Loss Method ◽  
Loss Method ◽  
Hcl Solution

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

Study on Corrosion Scale Inhibitor for Blast Furnace Gas TRT System

2013 ◽  
Vol 864-867 ◽  
pp. 1342-1345
Author(s):  
Fu Rong Zhou ◽  
Hu Zhang ◽  
Guang Wu Du ◽  
Wen Hua Wang
Keyword(s):  
Weight Loss ◽  
Blast Furnace ◽  
Corrosion Inhibitor ◽  
Inhibition Efficiency ◽  
Acid Anhydride ◽  
Scale Inhibitor ◽  
Corrosion Scale ◽  
Blast Furnace Gas ◽  
Weight Loss Method ◽  
Loss Method

Cyclohexylamine, morphine, ethanolamine, propiolic alcohol, seventeen alkenyl amide ethyl imidazoline, water depolymerization malaya acid anhydride, etc were chosen as the raw material of corrosion scale inhibitor in view of corrosion scaling reason and characteristic of blast furnace top gas pressure recovery turbine unit. The optimized formula of corrosion inhibitor have been obtained through orthogonal experiment. Corrosion and scale inhibitor performance were evaluated respectively by static weight-loss method, dynamic weight-loss method and calcium carbonate deposition. The results show that when these components are reasonable distributed, the corrosion effect is satisfied. When water depolymerization malaya acid anhydride is combined with the corrosion inhibitor, the corrosion and scale inhibition efficiency of composite inhibitor are more than 90%. Simulation blast furnace gas is adopted in dynamic simulation experiment, the corrosion inhibition efficiency is over 92%.

scholarly journals Coumarin-3-Amine as New Corrosion Inhibitor

2017 ◽  
Author(s):  
Ahmed Al-Amiery
Keyword(s):  
Nuclear Magnetic Resonance ◽  
Mild Steel ◽  
Corrosion Inhibitor ◽  
Corrosion Inhibitors ◽  
Inhibition Efficiency ◽  
Spectroscopic Techniques ◽  
Synthetic Compounds ◽  
Weight Loss Method ◽  
Organic Inhibitors ◽  
Loss Method

Corrosion inhibitors are the natural or synthetic compounds that have the ability to inhibit the average of corrosion and reduce the damage of the mild steel. Enormous organic inhibitors nowadays employed in the corrosion domain but excluded due to costly. Comparatively cheap, and stable organic compound, namely 3-((4-nitrobenzylidene)amino)coumarin, have been utilized as an excellent corrosion inhibitor in hydrochloric acid for mild steel. The inhibition efficiency has been figured regarding to weight loss method. The corrosion inhibitor was identified according to spectroscopic techniques namely Fourier transform infrared and nuclear magnetic resonance in addition to micro-elemental analysis. Inhibition efficiency for the studied inhibitor was 71.4% that, at the highest studied concentration.

scholarly journals Synergistic effect of ZnO nanoparticles with organic compound as corrosion inhibition

2020 ◽  
Author(s):  
Buraq T Sh AL-Mosawi ◽  
Mohammed M Sabri ◽  
Muhanad A Ahmed
Keyword(s):  
Weight Loss ◽  
Mild Steel ◽  
Corrosion Inhibitors ◽  
Inhibition Efficiency ◽  
Corrosion Process ◽  
Zno Nps ◽  
Weight Loss Method ◽  
Steel Surfaces ◽  
Loss Method ◽  
Isatin Derivative

Abstract In chemical manufactures, the corrosion inhibitors were added in order to reduce the corrosion of mild steel. Chemical molecules are often used on mild steel surfaces as portion of the latest finishing steps before painting and/or storage. Here, this work elucidated the utilization of an isatin derivative, namely, 3-((3-acetylphenyl)imino)indolin-2-one synergistic with zinc oxide nanoparticles for improving the impedance of mild steel (MS) against corrosion in 1.0 M hydrochloric acid using the weight loss method and scanning electron microscopy (SEM). Weight loss measurements demonstrated that the best 3-((3-acetylphenyl)imino)indolin-2-one concentration was 0.5 mM and the inhibition efficiency was 83% whereas the inhibition efficiency was 92% with addition of ZnO NPs. 3-((3-Acetylphenyl)imino)indolin-2-one retards the corrosion process at 300 K and demonstrates low inhibition efficiencies at 310, 320 and 330 K.

scholarly journals Optimization of Blended Guava and Fluted Pumpkin Leaves extract as corrosion inhibitor of mild steel in 0.5 m hydrochloric acid

2021 ◽  
Vol 40 (3) ◽  
pp. 393-403
Author(s):  
C.F Nwachukwu ◽  
I.M. Dagwa ◽  
B.I. Ugheoke
Keyword(s):  
Weight Loss ◽  
Mild Steel ◽  
Corrosion Inhibitor ◽  
Oil And Gas ◽  
Phytochemical Analysis ◽  
Fluted Pumpkin ◽  
Weight Loss Method ◽  
Loss Method ◽  
Weight Loss Result ◽  
Good Substitute

There are many plant extracts that have been studied for possible use as corrosion inhibitors in the oil and gas industries. Hence, this work is focused on optimization of blended Guava and Fluted Pumpkin Leaves extract as corrosion inhibitor of mild steel in HCI using Weight loss method. Response Surface Methodology of Design Expert trial version 12 StatEase was used to design and analyze the result of the 35-run experiments. Three factor-three level was adopted in the design. Time, Temperature and Inhibitor Quantity were the independent variables, while the acid concentration of 0.5M was constant throughout the experiments and Inhibition Efficiencies were measured using IE formula. Intervals of 1 hr, 0.2g, and 10°C were chosen for the immersion time, inhibitor quantity and temperature, respectively. Phytochemical analysis carried out on the Guava and Fluted Pumpkin Leaves shows that each leaf extract contains phytochemicals which are responsible for inhibiting corrosion. Weight loss result shows that the Blended extract reduces the corrosion rate of mild steel in 0.5M HCl. Additionally, 4 experiments for Blended Extract, Fluted Pumpkin, Guava Extract and Industrial Inhibitor were carried out at optimal conditions as predicted by the software at time 4.036 hr, temperature 49.5°C, inhibitor quantity 0.487g and ratio of 59.21GE:FP40.79 Inhibition Efficiencies of the Blended, Fluted Pumpkin, Guava Extracts and Industrial Inhibitor were 93.70%, 78.14%, 63.7% and 95.18%, respectively. The results show that the blended and Industrial Inhibitor compared well with the software predicted IE of 96.085%. Therefore, the blended extract could serve as good substitute to the industrial inhibitor.

SYNERGISTIC EFFECT OF HALIDE IONS ON THE CORROSION INHIBITION OF MILD STEEL IN SULPHURIC ACID USING METHYL, N-METHYL ETHYL AND ETHYL SUBSTITUTED γ-2,c-6-DIPHENYL PIPERIDIN-4-ONE SEMICARBAZONES

2018 ◽  
Vol 25 (02) ◽  
pp. 1850050
Author(s):  
V. SHANMUGA PRIYA ◽  
C. UMA RANI ◽  
S. VELRANI
Keyword(s):  
Weight Loss ◽  
Synergistic Effect ◽  
Mild Steel ◽  
Sulphuric Acid ◽  
Corrosion Inhibition ◽  
Inhibition Efficiency ◽  
Halide Ions ◽  
Ac Impedance Spectroscopy ◽  
Weight Loss Method ◽  
Loss Method

The synergistic effect of halide ions such as KCl, KBr and KI on the corrosion inhibition of mild steel in 1 N sulphuric acid by [Formula: see text]-2,c-6-diphenyl-t-3-methyl piperdin-4-ones with semicarbazone (01[Formula: see text]SC), [Formula: see text]-2,c-6-diphenyl-N-methyl-t-3-ethyl piperdin-4-ones with semicarbazone (02[Formula: see text]SC) and 2,6-diphenyl-t-3-ethyl piperdin-4-one with semicarbazone (03[Formula: see text]SC) has been examined by weight loss method, potentiodynamic polarization measurements and electrochemical AC impedance spectroscopy. Results show that substituted [Formula: see text]-2,c-6-diphenyl piperidin-4-ones with semicarbazone act as the perfect corrosion inhibitors and their inhibition efficiency increases with the addition of halide ions. The inhibitor (01[Formula: see text]SC) shows the inhibition efficiency of 78.28% (0.2[Formula: see text]mM) by using a weight loss method. The influence of I[Formula: see text], Br[Formula: see text] and Cl[Formula: see text] anions raises the inhibition efficiency of the substituted 2,6-diphenyl piperidin-4-ones with semicarbazone due to the synergistic effect. The synergistic effect of halide ions was formed in the following order: KI [Formula: see text] KBr [Formula: see text] KCl.

scholarly journals Corrosion Inhibition Effect of 1,10-Phenanthroline-5,6-diamine on Mild Steel in Hydrochloric Acid Solution

2018 ◽  
Author(s):  
Ahmed A. Al-Amiery
Keyword(s):  
Weight Loss ◽  
Hydrochloric Acid ◽  
Acid Solution ◽  
Mild Steel ◽  
Inhibition Efficiency ◽  
Inhibition Effect ◽  
Increase With Increase ◽  
Weight Loss Method ◽  
Loss Method ◽  
Hcl Solution

The inhibition impacts of 1,10-Phenanthroline-5,6-diamine (PTDA) on mild steel in 1 M HCl solution were investigated through weight loss method. The inhibition efficiencies of PTDA increase with increase in PTDA concentration at the temperature 303. Weight loss method indicate that PTDA is an excellent inhibitor the inhibition efficiency of 81.5% at the maximum PTDA concentration of 0.5 g/L at the temperature 303K.

scholarly journals Synergistic and Antagonistic Effects of Sodium Molybdate-Zn2+System

2012 ◽  
Vol 9 (4) ◽  
pp. 1746-1752 ◽  
Author(s):  
J. Wilson Sahayaraj ◽  
A. John Amalraj ◽  
Susai Rajendran ◽  
N. Vijaya
Keyword(s):  
Aqueous Solution ◽  
Weight Loss ◽  
Inhibition Efficiency ◽  
Sodium Molybdate ◽  
Antagonistic Effect ◽  
Protective Film ◽  
Antagonistic Effects ◽  
Polarization Study ◽  
Weight Loss Method ◽  
Loss Method

The inhibition efficiency (IE) of sodium molybdate (SM) in controlling corrosion of carbon steel in an aqueous solution containing 120 ppm of Cl-, in the absence and presence of Zn2+has been evaluated by weight-loss method. A synergistic effect exists between SM and Zn2+when the concentration of Zn2+is 25 ppm and above. Inhibition efficiencies obtained are greater than 85%. Antagonistic effect exists between SM and Zn2+when the concentration of Zn2+is 10 ppm and below. The SM-Zn2+system shows excellent IE up to third day. Above third day IE decreases. Acceleration of corrosion takes place. Excellent IE is shown at pH 5,7 and 12. At pH 9, IE decreases since Zn2+is precipitated as Zn(OH)2in the bulk of the solution. Polarization study reveals that SM-Zn2+system functions as a mixed inhibitor. FTIR spectra reveal that the protective film consists of Fe2+-SM complex and Zn(OH)2.

scholarly journals The inhibition of mild steel corrosion in 0.5 M H2SO4 solution by radish leaf extract

RSC Advances ◽  
2019 ◽  
Vol 9 (70) ◽  
pp. 40997-41009 ◽  
Author(s):  
Dongyi Li ◽  
Panpan Zhang ◽  
Xinyu Guo ◽  
Xiaowei Zhao ◽  
Ying Xu
Keyword(s):  
Weight Loss ◽  
Mild Steel ◽  
Electrochemical Method ◽  
Leaf Extract ◽  
Steel Corrosion ◽  
Inhibitory Effect ◽  
H2so4 Solution ◽  
Mild Steel Corrosion ◽  
Weight Loss Method ◽  
Loss Method

The inhibitory effect of radish leaf extract (RLE) on mild steel corrosion in 0.5 M H2SO4 was studied by the weight loss method and the electrochemical method.

Sign in / Sign up

Export Citation Format

Share Document