scholarly journals INFLUENCE OF CURING TEMPERATURE ON LONG-TERM STRENGTH OF ECOCEMENT CONCRETE WITH GROUND GRANULATED BLAST-FURNACE SLAG

2009 ◽  
Vol 74 (645) ◽  
pp. 1913-1920
Author(s):  
Yasuhiro NAGASHIO ◽  
Yoshihiro MASUDA
2021 ◽  
Vol 7 (3) ◽  
pp. 32
Author(s):  
Noorina Hidayu Jamil ◽  
Mohd. Mustafa Al Bakri Abdullah ◽  
Faizul Che Pa ◽  
Mohamad Hasmaliza ◽  
Wan Mohd Arif W. Ibrahim ◽  
...  

The main objective of this research was to investigate the influence of curing temperature on the phase transformation, mechanical properties, and microstructure of the as-cured and sintered kaolin-ground granulated blast furnace slag (GGBS) geopolymer. The curing temperature was varied, giving four different conditions; namely: Room temperature, 40, 60, and 80 °C. The kaolin-GGBS geopolymer was prepared, with a mixture of NaOH (8 M) and sodium silicate. The samples were cured for 14 days and sintered afterwards using the same sintering profile for all of the samples. The sintered kaolin-GGBS geopolymer that underwent the curing process at the temperature of 60 °C featured the highest strength value: 8.90 MPa, and a densified microstructure, compared with the other samples. The contribution of the Na2O in the geopolymerization process was as a self-fluxing agent for the production of the geopolymer ceramic at low temperatures.


2011 ◽  
Vol 324 ◽  
pp. 392-395
Author(s):  
Riad Derabla ◽  
Imen Mokrani ◽  
Mohamed Larbi Benmalek

Our contribution consists at the study of the effect of (0 %, 0.2 % and 0.34 %) dosage of an hardening accelerating plasticizer (Plastocrete 160, produced by Sika Aldjazair) on the properties of normal mortar and concretes prepared with portland cement artificial of Hadjar Soud cement factory (Skikda – Algeria) with addition of (10 % and 20 %) of granulated blast furnace slag finely crushed of the El Hadjar blast furnace (Annaba - Algeria). The tests are focused to the physical and mechanical characteristics of elaborated materials to knowing: setting time, porosity, water absorption capacity and the test of compressive strength at 2, 7 and 28 days. The results obtained show clearly the reliability of the additive used to accelerate the hardening and to obtain high strengths at early age, which increase by increasing of the additive dosage. For the slag, its low hydraulic capacity does not make it profitable than at the long term (beyond 28 days).


Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 442 ◽  
Author(s):  
Hyun-Min Yang ◽  
Seung-Jun Kwon ◽  
Nosang Vincent Myung ◽  
Jitendra Kumar Singh ◽  
Han-Seung Lee ◽  
...  

Ground granulated blast furnace slag (GGBFS) conventionally has been incorporated with ordinary Portland cement (OPC) owing to reduce the environmental load and enhance the engineering performance. Concrete with GGBFS shows different strength development of normal concrete, but sensitive, to exterior condition. Thus, a precise strength evaluation technique based on a quantitative model like full maturity model is required. Many studies have been performed on strength development of the concrete using equivalent age which is based on the apparent activation energy. In this process, it considers the effect of time and temperature simultaneously. However, the previous models on the apparent activation energy of concrete with mineral admixtures have limitation, and they have not considered the effect of temperature on strength development. In this paper, the apparent activation energy with GGBFS replacement ratio was calculated through several experiments and used to predict the compressive strength of GGBFS concrete. Concrete and mortar specimens with 0.6 water/binder ratio, and 0 to 60% GGBFS replacement were prepared. The apparent activation energy (Ea) was experimentally derived considering three different curing temperatures. Thermodynamic reactivity of GGBFS mixed concrete at different curing temperature was applied to evaluate the compressive strength model, and the experimental results were in good agreement with the model. The results show that when GGBFS replacement ratio was increased, there was a delay in compressive strength.


2014 ◽  
Vol 919-921 ◽  
pp. 2071-2075
Author(s):  
Jin Zha ◽  
Jin Hui Li ◽  
Yun Pan Jiao ◽  
Shao Hao Zhou

This paper studies the changes of composite binder basic properties caused by the addition of processed rice husk ash and blast furnace slag. Experimental results show that the fineness and pozzolanic activity of rice husk ash, slag in appropriate treatment are according to using standard. This novel composite binder becomes a little worse in availability performance, while its long-term strength is equivalent with normal cement.


2013 ◽  
Vol 575-576 ◽  
pp. 337-340
Author(s):  
Zai Bo Li ◽  
Xu Guang Zhao ◽  
San Yin Zhao ◽  
Tu Sheng He

For the purpose of high-efficiency recovery and utilization of steel slag in cement and concrete, a comparative research on the cementitious property of several kinds of steel slag in six different cementitious systems have been carried out. The results show that the changes of cementitious systems and the basicity of steel slag have no significant effect on the mortar fluidity. The cooperating use of steel slag and ground granulated blast furnace slag is helpful to activate the cementitious property of steel slag. The basicity of steel slag can generally reflect the long-term cementitious properties of steel slag.


2011 ◽  
Vol 287-290 ◽  
pp. 916-921
Author(s):  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Si Hwan Kim ◽  
Jang Hwa Lee

This paper examines the effects of the mixture ratio of fly ash/slag, the type of alkaline activators and curing conditions on the workability, compressive strength and microstructure of cementless alkali-activated mortar. The investigation showed that the mixture ratio of fly ash/slag and the type of alkaline activator have significant influence on the workability and strength, whereas the curing temperature has relatively poor effect. An alkali-activated mortar using a binder composed of 50% of fly ash and 50% of granulated blast furnace slag and alkaline activator made of 9M NaOH and sodium silicate in proportion of 1:1 is seen to be able to develop a compressive strength of 65 MPa at age of 28 days even when cured at ambient temperature of 20°C.


Sign in / Sign up

Export Citation Format

Share Document