АКУСТИЧНА ПОМІТНІСТЬ БЕЗПІЛОТНИХ ЛІТАЛЬНИХ АПАРАТІВ З СИЛОВИМИ УСТАНОВКАМИ НА БАЗІ ПОРШНЕВИХ ДВИГУНІВ

Author(s):  
В. В. Руденко ◽  
И. В. Калужинов ◽  
Н. А. Андрущенко

The presence in operation of many prototypes of UAVs with propeller propellers, the use of such devices at relatively low altitudes and flight speeds makes the problem of noise reduction from UAVs urgent both from the point of view of acoustic imperceptibility and ecology.The aim of the work is to determine a set of methods that help to reduce the visibility of UAVs in the acoustic range. It is shown that the main source of noise from the UAV on the ground is the power plant, which includes the engine and the propeller. The parameters of the power plants influencing the processes that determine the acoustic signature of the UAV were investigated. A comprehensive analysis of the factors affecting visibility was carried out. The power plants include two-stroke and four-stroke engines, internal combustion and two-blade propellers. The use of silencers on the exhaust of the internal combustion engine was considered. The spectral characteristics of the acoustic fields of the propeller-driven power plants for the operating sample of the UAV "Eco" were obtained. The measurements were carried out in one-third octave and 1/48 octave frequency bands under static conditions. The venue is the KhAI airfield. Note that the propellers that were part of the power plants operated at Reynolds numbers (Re0,75<2*105), which can significantly affect its aerodynamic and acoustic characteristics. It is shown that when choosing a UAV control system, one should take into account the fact that two-stroke piston engines are the dominant source in the noise of propeller-driven control systems in the absence of a hood and mufflers in the intake and exhaust tracts. The use of a four-stroke internal combustion engine significantly reduces the noise of the control system. In the general case, the position of the boundaries of the zone of acoustic visibility of a UAV at the location of the observer is determined by the ratio between the intensity of acoustic radiation perceived by the observer from the UAV and the intensity of sound corresponding to the natural acoustic background and depends on the degree of manifestation of acoustic effects accompanying the propagation of sound in a turbulent atmosphere - the refraction of sound waves. Absorption and dissipation of acoustic energy. The calculation and comparison of the UAV detection range was carried out taking into account the existing natural maskers.The results of experimental studies are presented that allow assessing the degree of acoustic signature of the UAV. A set of measures aimed at reducing the intensity of the acoustic signature of the UAV in various regions of the radiation spectrum has been determined.

2021 ◽  
pp. 13-20
Author(s):  

The prospects of using the gas-static suspension of the internal combustion engine piston in transport vehicles and power plants are considered. The diagram of the piston and the method for calculating the stiffness and bearing capacity of the gas layer surrounding the piston are presented, as well as the results of experiments that showed the relevance of this method. The possibility of gas and static centering of the engine piston is confirmed. Keywords: internal combustion engine, piston, gasstatic suspension, stiffness, bearing capacity, gas medium. [email protected]


2021 ◽  
pp. 15-19
Author(s):  

The results of a study of the control processes of an automated transmission and internal combustion engine of a transport unmanned tracked vehicle when the speed of movement is set by an external control device are presented. Keywords: unmanned tracked vehicle, algorithm, motion control, onboard gear unit, programmable logic controller, cruise control. [email protected]


2011 ◽  
Vol 159 (1) ◽  
pp. 155-167
Author(s):  
Włodzimierz KUPICZ ◽  
Stanisław NIZIŃSKI

The paper presents a new method for diagnosing an internal combustion engine with compression ignition under traction conditions. The gist lies in determining the engine torque on the basis of acceleration recording in traffic conditions. The results of extensive preliminary and basic experimental studies have been discussed. Three options have been developed of the internal combustion engine diagnostic model, using the trivalent assessment of states. State control and engine damage localization algorithms have been proposed. The new method has been examined under traction conditions. The probability of the internal combustion engine correct diagnosis ranges between 0.85÷1.


Author(s):  
Ryan Falkenstein-Smith ◽  
Kang Wang ◽  
Ryan Milcarek ◽  
Jeongmin Ahn

New York State is expected to experience future population growth that is increasingly concentrated in urban areas, where there is already a heavy burden on the existing energy, water and waste management infrastructure. To meet aggressive environmental standards (such as that established by the State’s “80x50” goal), future electrical power capacity must produce substantially fewer greenhouse gas emissions than currently generated by coal- or natural gas-fired power plants. Currently, biogas is combusted to produce heat and electricity via an internal combustion engine generator set. A conventional internal combustion engine generator set is 22–45 % efficient in converting methane to electricity, thus wasting 65–78 % of the biogas energy content unless the lower temperature heat can be recovered. Fuel cells, on the other hand, are 40–60 % efficient in converting methane to electrical energy, and 80–90 % efficient for cogeneration if heat (> 400 °C) is recovered and utilized for heating and cooling in the community power system. This current research studies the feasibility of a community biomass-to-electricity power system which offers significant environmental, economic and resilience improvements over centrally-generated energy, with the additional benefit of reducing or eliminating disposal costs associated with landfills and publicly-owned treatment works (POTWs). Flame Fuel Cell (FFC) performance was investigated while modifying biogas content and fuel flow rate. A maximum power density peak at 748 mWcm-2 and an OCV of 0.856 V was achieved. It should be noted that the performance obtained with the model biofuel is comparable to the performances of direct methane fueled DC-SOFC and SC-SOFC. The common trends also concluded an acceptable range for optimal performance. Although the methane to CO2 ratios of 3:7 and 2:8 produced power, they are not the strongest ratios to have optimal performance, meaning that operation should stay between the 6:4/4:6 ratio range. Lastly, the amount of air added to the biogas mixture is crucial to achieving the optimal performance of the cell. The data obtained confirmed the feasibility of a biofuel driven fuel cell CHP device capable of achieving higher efficiency than existing technologies. The significant power output produced from the sustainable biogas composition is competitive with current hydrocarbon fuel sources. This idea can be expanded for a community waste management infrastructure.


Sign in / Sign up

Export Citation Format

Share Document