scholarly journals Research on a New Single-End Fault Location Method for Single-Phase Grounding Faults of Transmission Lines Through Transition Resistance

2021 ◽  
Vol 9 ◽  
Author(s):  
Botong Li ◽  
Lin Shi ◽  
Weijie Wen ◽  
Bin Li ◽  
Xiaolong Chen ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Calculation Method ◽  
Fault Location ◽  
Single Phase ◽  
Necessary Conditions ◽  
Simple Expression ◽  
Location Method ◽  
Terminal System ◽  
The Poor ◽  
Transition Resistance

A single-end fault location method for single-phase nonmetallic grounding faults of transmission lines in a double terminal system is studied and proposed. First, the reason for the poor accuracy of the single-end fault location method in case of single-phase nonmetallic grounding faults is analyzed theoretically, and the necessary conditions for the single-end accurate fault location are put forward. Second, under the necessary conditions of the single-end accurate fault location, according to the topology of fault component networks, the calculation method of the single-end accurate fault location of transmission lines in a double terminal system is studied. Moreover, the influence of line capacitance is considered in this fault location method, and a simple expression for calculating the fault distance is obtained. Finally, the transmission line with a single-phase nonmetallic grounding fault is modeled in PSCAD; therefore, the correctness and the ability against transition resistance of the new single-end fault location method are verified by simulation.

A Fault Location Method for HVDC Transmission Lines

2014 ◽  
Vol 556-562 ◽  
pp. 2723-2727 ◽  
Author(s):  
Lu Hua Xing ◽  
Qing Chen ◽  
Bing Lei Xue
Keyword(s):  
Transmission Lines ◽  
Traveling Wave ◽  
Fault Location ◽  
Propagation Characteristic ◽  
Location Method ◽  
Hvdc Transmission ◽  
High Voltage Direct Current ◽  
Current Transmission ◽  
Hvdc Transmission Lines ◽  
Transition Resistance

A fault location method for HVDC (High Voltage Direct Current) transmission lines is proposed in this paper, using voltages and currents measured at two terminals of dc lines in time domain. Fault traveling waves propagate from the fault point to both terminals along the faulted line. The position that the traveling wave head arrives at some moment after the fault can be used to calculate the fault location. To determine the arrival positions of traveling wave head at each time indirectly, propagation characteristic curves of traveling wave heads at local and the remote terminals are calculated with distribution currents using the stationary wavelet transform. The accuracy of fault location will not be affected by transition resistance and fault position. Simulation results show that the presented fault location method can achieve quick and accurate fault location on the whole line under probable operation modes of a bipolar HVDC transmission system.

A New PMU-Based Fault Location Algorithm for Three-Terminal

2013 ◽  
Vol 634-638 ◽  
pp. 3925-3929
Author(s):  
Hong Yu Shen ◽  
Wen Jun Zhang ◽  
Yu Bo Duan ◽  
Jian Jun Xu
Keyword(s):  
Fault Zone ◽  
Transmission Lines ◽  
Fault Location ◽  
Measurement Data ◽  
Data Synchronization ◽  
Distributed Parameter ◽  
Matlab Simulation ◽  
Location Method ◽  
Terminal System ◽  
Location Algorithm

Existing two-terminal fault location method can not be directly applied to the three-terminal transmission lines, this paper presents a new PMU-based fault location algorithm for three-terminal transmission lines. The development of the algorithm takes advantage of PMU measurement data synchronization, uses distributed parameter line model, first of all judging the fault zone after a failure, uses Thevenin's Theorem to merge the non-slip fault, so the three-terminal system is simplified the two-terminal system, Then we can use the two-terminal fault location principle of fault location. Through MATLAB simulation shows the correctness of the algorithm.

A Novel Fault-location Method for HVDC Transmission Lines Based on Concentric Relaxation Principle and Wavelet Packet

2020 ◽  
Vol 13 (5) ◽  
pp. 705-716
Author(s):  
Congshan Li ◽  
Ping He ◽  
Feng Wang ◽  
Cunxiang Yang ◽  
Yukun Tao ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Traveling Wave ◽  
Fault Location ◽  
Wave Attenuation ◽  
Wavelet Packet ◽  
Low Frequency ◽  
Evaluation Process ◽  
Location Method ◽  
Hvdc Transmission ◽  
Instantaneous Energy

Background: A novel fault location method of HVDC transmission line based on a concentric relaxation principle is proposed in this paper. Methods: Due to the different position of fault, the instantaneous energy measured from rectifier and inverter are different, and the ratio k between them is the relationship to the fault location d. Through the analysis of amplitude-frequency characteristics, we found that the wave attenuation characteristic of low frequency in the traveling wave is stable, and the amplitude of energy is larger, so we get the instantaneous energy ratio by using the low-frequency data. By using the method of wavelet packet decomposition, the voltage traveling wave signal was decomposed. Results: Finally, calculate the value k. By using the data fitting, the relative function of k and d can be got, that is the fault location function. Conclusion: After an exhaustive evaluation process considering different fault locations, fault resistances, and noise on the unipolar DC transmission system, four-machine two-area AC/DC parallel system, and an actual complex grid, the method presented here showed a very accurate and robust behavior.

scholarly journals A Novel Single-Terminal Fault Location Method for AC Transmission Lines in a MMC-HVDC-Based AC/DC Hybrid System

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2066 ◽  
Author(s):  
Shimin Xue ◽  
Junchi Lu ◽  
Chong Liu ◽  
Yabing Sun ◽  
Baibing Liu ◽  
...  
Keyword(s):  
Transmission Lines ◽  
Fault Location ◽  
Control Strategies ◽  
Linear Regression Analysis ◽  
Location Method ◽  
Fault Resistance ◽  
Ac Networks ◽  
Minimum Residual ◽  
Ac Transmission ◽  
Location Methods

Accurate and reliable fault location method for alternating current (AC) transmission lines is essential to the fault recovery. MMC-based converter brings exclusive non-linear characteristics to AC networks under single-phase-to-ground faults, thus influencing the performance of the fault location method. Fault characteristics are related to the control strategies of the converter. However, the existing fault location methods do not take the control strategies into account, with further study being required to solve this problem. The influence of the control strategies to the fault compound sequence network is analyzed in this paper first. Then, a unique boundary condition that the fault voltage and negative-sequence fault current merely meet the direct proportion linear relationship at the fault point, is derived. Based on these, a unary linear regression analysis is performed, and the fault can be located according to the minimum residual sum function principle. The effectiveness of the proposed method is verified by PSCAD/EMTDC simulation platform. A large number of simulation results are used to verify the advantages on sampling frequency, fault resistance, and fault distance. More importantly, it provides a higher ranging precision and has extensive applicability.

scholarly journals Extending the Application of One-Terminal Fault Location Method Available in Actual Time Domain Relay

2020 ◽  
Author(s):  
Gustavo A. Cunha ◽  
Felipe V. Lopes ◽  
Tiago H. Honorato
Keyword(s):  
Transmission Lines ◽  
Time Domain ◽  
Traveling Wave ◽  
Fault Location ◽  
Reflected Waves ◽  
Location Method ◽  
Actual Time ◽  
The One

Traveling wave-based fault location has attracted more and more attention from industries worldwide. This theory allowed the implementation of functions in order to increase the reliability of the obtained fault location results. Among existing functions, the classical one-terminal method requires the detection of the wave reflected from the fault, which is still considered a challenging task. A commercial relay was released with a function able to identify these reflected waves by evaluating patterns and weighted hypotheses, identifying the wavefront most likely to be the one re ected from the fault. However, as this function is embedded into a relay, it is not possible to change the method settings. Thus, this paper presents a validation of this function which is implemented externally to the relay. Besides, its application is extended for transmission lines to which the relay can not be applied, such as huge HVDC lines.

Sign in / Sign up

Export Citation Format

Share Document