scholarly journals Free and Forced Vibration Modes of the Human Fingertip

2021 ◽  
Vol 11 (12) ◽  
pp. 5709
Author(s):  
Gokhan Serhat ◽  
Katherine J. Kuchenbecker
Keyword(s):  
Forced Vibration ◽  
Three Dimensional ◽  
Element Model ◽  
Vibration Modes ◽  
Form And Function ◽  
Dimensional Finite Element ◽  
Deformable Bodies ◽  
Vibration Responses ◽  
Three Dimensional Finite Element ◽  
And Function

Computational analysis of free and forced vibration responses provides crucial information on the dynamic characteristics of deformable bodies. Although such numerical techniques are prevalently used in many disciplines, they have been underutilized in the quest to understand the form and function of human fingers. We addressed this opportunity by building DigiTip, a detailed three-dimensional finite element model of a representative human fingertip that is based on prior anatomical and biomechanical studies. Using the developed model, we first performed modal analyses to determine the free vibration modes with associated frequencies up to about 250 Hz, the frequency at which humans are most sensitive to vibratory stimuli on the fingertip. The modal analysis results reveal that this typical human fingertip exhibits seven characteristic vibration patterns in the considered frequency range. Subsequently, we applied distributed harmonic forces at the fingerprint centroid in three principal directions to predict forced vibration responses through frequency-response analyses; these simulations demonstrate that certain vibration modes are excited significantly more efficiently than the others under the investigated conditions. The results illuminate the dynamic behavior of the human fingertip in haptic interactions involving oscillating stimuli, such as textures and vibratory alerts, and they show how the modal information can predict the forced vibration responses of the soft tissue.

Modal Analysis for Swing-Arm of LED Die Bonder

2011 ◽  
Vol 422 ◽  
pp. 379-382
Author(s):  
Wei Chuang Quan ◽  
Mei Fa Huang ◽  
Zhi Yue Wang ◽  
Da Wei Zhang
Keyword(s):  
Modal Analysis ◽  
Vibration Mode ◽  
Three Dimensional ◽  
Element Model ◽  
Mode Shapes ◽  
Vibration Modes ◽  
Lead Frame ◽  
Swing Arm ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Led die bonder used for bond lead frame and chip is one of the key equipment of led production line. The swing-arm is an important component of led die bonder and its dynamic characteristics will directly affect the piece accuracy. At present, the accuracy and efficiency of led die bonder are limited because of the vibration of the swing-arm. In solving this problem, a three-dimensional finite-element model for swing-arm is built to provide analytical frequencies and vibration modes. Then the modal distribution and vibration mode shapes for swing-arm are obtained after analyzing the modal by ansys10.0. Finally the dynamics effects of this structure by modal frequency and vibration mode are analyzed. The modal analysis of structural would provide the reference to dynamics analysis and structural optimization for swing-arm in practical use.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Internal Force on and Deformation of Steel Assembled Supporting Structure of Foundation Pit under Thermal Stress

2021 ◽  
Vol 11 (5) ◽  
pp. 2225
Author(s):  
Fu Wang ◽  
Guijun Shi ◽  
Wenbo Zhai ◽  
Bin Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
High Strength ◽  
Element Model ◽  
Internal Force ◽  
Foundation Pit ◽  
Dimensional Finite Element ◽  
Influence Of Temperature On ◽  
Scale Experiment ◽  
Three Dimensional Finite Element

The steel assembled support structure of a foundation pit can be assembled easily with high strength and recycling value. Steel’s performance is significantly affected by the surrounding temperature due to its temperature sensitivity. Here, a full-scale experiment was conducted to study the influence of temperature on the internal force and deformation of supporting structures, and a three-dimensional finite element model was established for comparative analysis. The test results showed that under the temperature effect, the deformation of the central retaining pile was composed of rigid rotation and flexural deformation, while the adjacent pile of central retaining pile only experienced flexural deformation. The stress on the retaining pile crown changed little, while more stress accumulated at the bottom. Compared with the crown beam and waist beam 2, the stress on waist beam 1 was significantly affected by the temperature and increased by about 0.70 MPa/°C. Meanwhile, the stress of the rigid panel was greatly affected by the temperature, increasing 78% and 82% when the temperature increased by 15 °C on rigid panel 1 and rigid panel 2, respectively. The comparative simulation results indicated that the bending moment and shear strength of pile 1 were markedly affected by the temperature, but pile 2 and pile 3 were basically stable. Lastly, as the temperature varied, waist beam 2 had the largest change in the deflection, followed by waist beam 1; the crown beam experienced the smallest change in the deflection.

Process Modeling in Laser Deposition of Multilayer SS410 Steel

2007 ◽  
Vol 129 (6) ◽  
pp. 1028-1034 ◽  
Author(s):  
Liang Wang ◽  
Sergio Felicelli
Keyword(s):  
Phase Transformation ◽  
Temperature Distribution ◽  
Three Dimensional ◽  
Element Model ◽  
Traverse Speed ◽  
Processing Parameters ◽  
Dimensional Finite Element ◽  
Net Shaping ◽  
Three Dimensional Finite Element ◽  
Continuous Cooling Transformation Diagram

A three-dimensional finite element model was developed to predict the temperature distribution and phase transformation in deposited stainless steel 410 (SS410) during the Laser Engineered Net Shaping (LENS™) rapid fabrication process. The development of the model was carried out using the SYSWELD software package. The model calculates the evolution of temperature in the part during the fabrication of a SS410 plate. The metallurgical transformations are taken into account using the temperature-dependent material properties and the continuous cooling transformation diagram. The ferritic and martensitic transformation as well as austenitization and tempering of martensite are considered. The influence of processing parameters such as laser power and traverse speed on the phase transformation and the consequent hardness are analyzed. The potential presence of porosity due to lack of fusion is also discussed. The results show that the temperature distribution, the microstructure, and hardness in the final part depend significantly on the processing parameters.

Mechanical Simulation of Knee Movement in Basketball Shooting

2013 ◽  
Vol 336-338 ◽  
pp. 760-763
Author(s):  
Hui Yue
Keyword(s):  
Finite Element ◽  
Cruciate Ligament ◽  
Three Dimensional ◽  
Element Model ◽  
Basketball Player ◽  
Knee Movement ◽  
Dimensional Finite Element ◽  
Anterior Cruciate ◽  
Three Dimensional Finite Element

A short explanation of the finite element method as a powerful tool for mathematical modeling is provided, and an application using constitutive modeling of the behavior of ligaments is introduced. Few possible explanations of the role of water in ligament function are extracted from two dimensional finite element models of a classical ligament. The modeling is extended to a three dimensional finite element model for the human anterior cruciate ligament. Simulation of ligament force in pitching motion of basketball player is studied in this paper.

Sign in / Sign up

Export Citation Format

Share Document