scholarly journals Settlement and Bearing Capacity of Rectangular Footing in Reliance on the Pre-Overburden Pressure of Soil Foundation

2021 ◽  
Vol 11 (24) ◽  
pp. 12124
Author(s):  
Zaven G. Ter-Martirosyan ◽  
Armen Z. Ter-Martirosyan ◽  
Huu H. Dam
Keyword(s):  
Bearing Capacity ◽  
Shear Strain ◽  
Volumetric Strain ◽  
Soil Mass ◽  
Point Load ◽  
Unit Weight ◽  
Basic Solution ◽  
Mean Stress ◽  
Overburden Pressure ◽  
Non Linear

This article presents a solution for the quantitative evaluation of the stress–strain state (SSS) and the bearing capacity of rectangular foundations, factoring in the unit weight of the soil mass and different values of pre-overburden pressure (POP). In order to assess the SSS of the soil subgrade below a rigid rectangular footing under a uniformly distributed load, the authors applied the Boussinesq basic solution for an elastic half-space subjected to a vertical point load on its surface. As a result, the formulas for vertical stress, mean stress, shear strain, and volumetric strain for any point in Cartesian coordinates (x, y, z) and foundation settlement were determined. Additionally, the application of Hencky’s system of physical equations, with non-linear dependencies between mean stress and volumetric strain as well as deviator stress and shear strain, along with the experimental curves, depicts the relationships between bulk modulus and volume stress, and shear modulus and shear stress. The authors point out the non-linear behavior of the subgrade soil and propose a method for estimating the bearing capacity of a rigid rectangular foundation.

Foundation Numerical Analysis on Soft Soil Reinforced with Stone Columns

2011 ◽  
Vol 94-96 ◽  
pp. 190-195 ◽  
Author(s):  
Shu Li Wang ◽  
Man Gen Mu ◽  
Jing Yu Dai ◽  
Xiao Huan Hu
Keyword(s):  
Numerical Analysis ◽  
Bearing Capacity ◽  
Design Method ◽  
Soft Soil ◽  
Volumetric Strain ◽  
Vertical Displacement ◽  
Area Ratio ◽  
Stone Columns ◽  
Mean Stress ◽  
Maximum Shear Strain

A parametric study of an foundation on soft soils reinforced with stone columns is performed using Phase2D. The real foundation is modeled and its bearing capacity is decided by the columns and their surrounding soft soil. The following parameters are analysed: the replacement area ratio, the deformability, mean stress, absolute horizontal (vertical) displacement, volumetric strain, maximum shear strain of the foundation. Based on the results of this study, a new design method is proposed: for decreasing the settlement and satisfying bearing capacity, increasing the replacement area ratio is good idea.

scholarly journals Influence of the groundwater level on the bearing capacity of shallow foundations on the rock mass

2021 ◽  
Author(s):  
Ana Alencar ◽  
Rubén Galindo ◽  
Svetlana Melentijevic
Keyword(s):  
Rock Mass ◽  
Bearing Capacity ◽  
Groundwater Level ◽  
Sensitivity Study ◽  
Shallow Foundations ◽  
Unit Weight ◽  
Geological Strength Index ◽  
Strength Index ◽  
Mass Type

AbstractThe presence of the groundwater level (GWL) at the rock mass may significantly affect the mechanical behavior, and consequently the bearing capacity. The water particularly modifies two aspects that influence the bearing capacity: the submerged unit weight and the overall geotechnical quality of the rock mass, because water circulation tends to clean and open the joints. This paper is a study of the influence groundwater level has on the ultimate bearing capacity of shallow foundations on the rock mass. The calculations were developed using the finite difference method. The numerical results included three possible locations of groundwater level: at the foundation level, at a depth equal to a quarter of the footing width from the foundation level, and inexistent location. The analysis was based on a sensitivity study with four parameters: foundation width, rock mass type (mi), uniaxial compressive strength, and geological strength index. Included in the analysis was the influence of the self-weight of the material on the bearing capacity and the critical depth where the GWL no longer affected the bearing capacity. Finally, a simple approximation of the solution estimated in this study is suggested for practical purposes.

Bearing capacity of non-linear metallic spiders used in point supported glass facades

2012 ◽  
Vol 12 (2) ◽  
pp. 191-204 ◽  
Author(s):  
Yuanqing Wang ◽  
Huanxin Yuan ◽  
Yongjiu Shi ◽  
Yu Zou
Keyword(s):  
Bearing Capacity ◽  
Non Linear

scholarly journals Effect of Pile Spacing on Group Efficiency in Gypseous Soil

2019 ◽  
Vol 5 (2) ◽  
pp. 373 ◽  
Author(s):  
Bilal Jabbar Noman ◽  
Safaa H. Abd-Awn ◽  
Hassan O. Abbas
Keyword(s):  
Bearing Capacity ◽  
Load Condition ◽  
Soil Mass ◽  
Deep Foundation ◽  
Collapsible Soil ◽  
Floating Pile ◽  
Group Efficiency ◽  
Gypsum Content ◽  
Group Pile ◽  
Gypseous Soil

As a matter of fact, the gypseous soil is usually considered as collapsible soil, such type of soil illustrates high resistance to settlement and high bearing capacity when it is dry, but it loses these characteristics when it is inundated and collapses excessively because of the sudden decrease in the volume of the surrounding soil mass. It is founded in the arid and semi-arid regions of the world in Asia, South Asia (Iraq, Syria, Jordan, Yemen, and Iran), North Africa, North America, moreover, it covers more than (31%) of the surface area in Iraq. Gypseous soil is one of the most difficult problems facing the process of building any project because of the difficulty of preventing leakage of water to the soil in practice. Deep foundation (piles) are one of the most common types used in collapsible soils which penetrating problematic soil layers and reaching more hard ones (end bearing piles) or transfers loads depending on skin friction (floating pile). The current work is directed to study the behavior of single and group driven pile of square pattern (4 piles) in case of floating pile (friction pile) with different spacing (2D, 4D, 6D) and length to diameter (L/D) ratio of (20) in this special medium dense soil (gypsum content 30% and 61%) under axial load condition. The investigation was carried out to measure the soil collapse before and after inundation. The results showed that the group efficiency for spacing 2D is less than one while for spacing 4D and 6D are more than that value. In addition, the spacing 4D was more efficient to carry 4 group pile in both dry and soaked cases, in addition, the result showed a high reduction in the bearing capacity at inundation state of group pile of (82% in gypsum content 30%) and ( 87% in gypsum content 61%) with respect to dry state.

scholarly journals EVOLUTION OF THE CARBON NANOTUBE BUNDLE STRUCTURE UNDER BIAXIAL AND SHEAR STRAINS

2020 ◽  
pp. 525
Author(s):  
Leysan Kh. Rysaeva ◽  
Dmitry V. Bachurin ◽  
Ramil T. Murzaev ◽  
Dina U. Abdullina ◽  
Elena A. Korznikova ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Shear Strain ◽  
Cross Sections ◽  
Degrees Of Freedom ◽  
Shear Bands ◽  
Volumetric Strain ◽  
Structural Evolution ◽  
Biaxial Compression ◽  
Chain Model ◽  
Nanotube Bundle

Close packed carbon nanotube bundles are materials with highly deformable elements, for which unusual deformation mechanisms are expected. Structural evolution of the zigzag carbon nanotube bundle subjected to biaxial lateral compression with the subsequent shear straining is studied under plane strain conditions using the chain model with a reduced number of degrees of freedom. Biaxial compression results in bending of carbon nanotubes walls and formation of the characteristic pattern, when nanotube cross-sections are inclined in the opposite directions alternatively in the parallel close-packed rows. Subsequent shearing up to a certain shear strain leads to an appearance of shear bands and vortex-like displacements. Stress components and potential energy as the functions of shear strain for different values of the biaxial volumetric strain are analyzed in detail. A new mechanism of carbon nanotube bundle shear deformation through cooperative, vortex-like displacements of nanotube cross sections is reported.

scholarly journals The appropriateness of sum scores as estimates of factor scores in the multiple factor analysis of ordered-categorical responses.

2020 ◽  
Author(s):  
Pere Ferrando ◽  
Urbano Lorenzo-Seva
Keyword(s):  
Factor Analysis ◽  
Unit Weight ◽  
Factor Scores ◽  
Multiple Factor Analysis ◽  
Non Linear ◽  
Categorical Responses ◽  
Sum Scores ◽  
Biased Estimates ◽  
Ordered Categorical ◽  
Multiple Factor

<p>Unit-weight sum scores (UWSSs) are routinely used as estimates of factor scores on the basis of solutions obtained with the non-linear exploratory factor analysis (EFA) model for ordered-categorical responses. Theoretically, this practice results in a loss of information and accuracy, and is expected to lead to biased estimates. However, the practical relevance of these limitations is far from clear. In this article we adopt an empirical view, and propose indices and procedures (some of them new) for assessing the appropriateness of UWSSs in non-linear EFA applications. A new automated approach for obtaining UWSSs that maximize fidelity and correlational accuracy is proposed. The appropriateness of UWSSs under different conditions and the behavior of the present proposal in comparison with other more common approaches are assessed with a simulation study. A tutorial for interested practitioners is presented using an illustrative example based on a well-known personality questionnaire. All the procedures proposed in the article have been implemented in a well-known noncommercial EFA program. </p>

Assessment of Load-Bearing Capacity of Bridges

2017 ◽  
Vol 259 ◽  
pp. 113-118 ◽  
Author(s):  
Jaroslav Navrátil ◽  
Michal Drahorád ◽  
Petr Ševčík
Keyword(s):  
Bearing Capacity ◽  
Prestressed Concrete ◽  
Iterative Solution ◽  
Concrete Bridges ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Prestressed Concrete Bridges ◽  
Existing Structures ◽  
Non Linear

The paper aims to the determination of load-bearing capacity of reinforced/prestressed concrete bridges subjected to the combination of all components of internal forces according to Eurocode standards for assessment of existing structures. Undoubtedly bridge load rating is laborious hand-iterative process, especially when it comes to reinforced and/or prestressed concrete bridges. The engineer can spend days and weeks trials and errors in the estimation of bridge load-carrying capacity. The problem lies in the determination of load-bearing capacity of cross-section subjected to the combination of normal and shear forces, bending and torsional moments. Due to the different effects of permanent and variable loads and the non-linear behavior of structural materials, the problem becomes non-linear and its solution requires the use of suitable iterative method. Optimized iterative solution was implemented into IDEA StatiCa software and the results are presented in this paper.

scholarly journals Bearing Capacity Analysis and Zoning of Kathmandu for Shallow Foundations

2018 ◽  
Vol 4 ◽  
pp. 111-117
Author(s):  
Ram Krishna Danai ◽  
Indra Prasad Acharya
Keyword(s):  
Bearing Capacity ◽  
Numerical Models ◽  
Failure Criteria ◽  
Unit Weight ◽  
Soil Parameters ◽  
Primary Concern ◽  
Borehole Data ◽  
Element Analysis ◽  
Theoretical Approaches ◽  
Coulomb Failure

The bearing capacity of foundation is the primary concern in the field of geotechnical engineering. In this study numerical models are developed for each of the secondary borehole data collected around Kathmandu valley. Finite element analysis (i.e. PLAXIS 2D) is carried out using Mohr-coulomb failure criteria to represent two dimensional soil models. Foundation is aimed to model as square footing and prescribed settlement of 10% of footing width is provided to obtain corresponding bearing capacity. In plaxis, effective stress is considered as an ultimate bearing capacity. Drained behavior with axisymmetical models have been considered for soil model in plaxis software. Various soil parameters like C (Cohesion), γ (unit weight), Φ (Frictional angle), ν (Poison ratio), E (Elasticity) for each 1.5m and 3m depths have been considered in models and in theoretical approaches.

scholarly journals Bearing Capacity of Ring Foundations on Sand Overlying Clay

2020 ◽  
Vol 10 (13) ◽  
pp. 4675
Author(s):  
Chaowei Yang ◽  
Zhiren Zhu ◽  
Yao Xiao
Keyword(s):  
Bearing Capacity ◽  
Friction Angle ◽  
Failure Criteria ◽  
Unit Weight ◽  
Sand Layer ◽  
Collapse Mechanisms ◽  
Internal Radius ◽  
Vertical Bearing ◽  
Vertical Bearing Capacity ◽  
Ring Foundations

The vertical bearing capacity of rough ring foundations resting on a sand layer overlying clay soil is computed in this study by using finite element limit analysis (FELA). The sands and clays are assumed as elastoplastic models, obeying Mohr–Coulomb and Tresca failure criteria, respectively. Based on the FELA results, design charts are provided for evaluating the ultimate bearing capacity of ring foundations, which is related to the undrained shear strength of the clay, the thickness, the internal friction angle, the unit weight of the sand layer, and the ratio of the internal radius to the external radius of the footing. A certain thickness, beyond which the clay layer has a negligible effect on the bearing capacity, is determined. The collapse mechanisms are also examined and discussed.

scholarly journals The Horizontal Bearing Capacity of Composite Concrete-Filled Steel Tube Piles

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Yunxiu Dong ◽  
Zhongju Feng ◽  
Haibo Hu ◽  
Jingbin He ◽  
Qilang Zhang ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Soil Compaction ◽  
Soil Mass ◽  
Steel Tube ◽  
Continuous Increase ◽  
Concrete Filled Steel Tube ◽  
Concrete Piles ◽  
Compaction Zone ◽  
Reinforced Concrete Piles ◽  
Centrifugal Model

Steel casings (SCs) are extensively and increasingly used to stabilize the borehole wall in the construction of bridge pile foundations. Steel casings (SCs), together with reinforced concrete piles (RCPs), form composite concrete-filled steel tube piles (CCFSTPs), which differ significantly from ordinary RCPs in horizontal bearing capacity. In this study, based on the characteristics of CCFSTPs, the horizontal bearing capacity of a CCFSTP was examined through a centrifugal model test with the length of the steel casing (LSC) and the modulus of the soil mass in the steel casing soil compaction zone (ESCSC_zone) as variables. Pile-side soil resistance, load-displacement curves, and pile moment curves were obtained for the CCFSTP. The results show that increasing LSC within a range of 12 cm significantly increases the ultimate horizontal bearing capacity of the CCFSTP, and further increasing LSC beyond 12 cm produces a continuous increase in the ultimate horizontal bearing capacity of the CCFSTP but only to an insignificant extent. In addition, increasing ESCSC_zone increases the ultimate horizontal bearing capacity of the CCFSTP, but to a relatively small extent. The results of this study provide a theoretical basis and technical support for the design and construction of CCFSTPs.

Sign in / Sign up

Export Citation Format

Share Document