scholarly journals Effect of Process Parameters and Layer Thickness on the Quality and Performance of Ti-6Al-4V Fabricated by Selective Laser Melting

Coatings ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1323
Author(s):  
Yanlong Jing ◽  
Peng Wang ◽  
Xiaoling Yan
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Exposure Time ◽  
Process Parameters ◽  
Laser Power ◽  
Single Track ◽  
Laser Melting ◽  
Powder Bed ◽  
Point Distance

To improve the quality of thick powder bed and realize the matching of thick powder bed and thin powder bed in the later stage, the influence of process parameters for the single-track, multi-layer fabrication, relative density, surface quality, defect, remelting, and boundary optimization performance of different layer thicknesses of Ti-6Al-4V fabricated by selective laser melting were investigated. It is more conducive to the stable forming of single-track when the point distance is half the diameter of the laser beam, and the exposure time is appropriately extended. The thin powder bed needs the corresponding point distance and exposure time under the laser power of 280–380 W to obtain high-density specimens. The thick powder bed needs to be able to ensure the formation of high-quality specimens under the smaller point distance and longer exposure time under higher laser power of 380 W. Both thick powder bed and thin powder bed will cause un-melted defects between molten pools, spheroidization defects caused by splashing, and microporous defects. The remelting process can significantly improve the surface quality of the formed specimen, but the surface quality of the thick powder bed is worse than that of the thin powder bed. The boundary quality of thick powder bed is worse than that of thin powder bed, and the boundary shape has a greater influence on the quality of the SLM forming boundary. Different strategies should be adopted to form the boundary of different shapes. Increasing the boundary count and increasing the laser power are more conducive to the improvement of boundary quality.

The mechanism of process parameters influencing the AlSi10Mg side surface quality fabricated via laser powder bed fusion

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Shimin Dai ◽  
Hailong Liao ◽  
Haihong Zhu ◽  
Xiaoyan Zeng
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Process Parameters ◽  
Laser Power ◽  
Side Surface ◽  
Laser Powder Bed Fusion ◽  
Scanning Velocity ◽  
Content Type ◽  
Powder Bed

Purpose For the laser powder bed fusion (L-PBF) technology, the side surface quality is essentially important for industrial applicated parts, such as the inner flow parts. Contour is generally adopted at the parts’ outline to enhance the side surface quality. However, the side surface roughness (Ra) is still larger than 10 microns even with contour in previous studies. The purpose of this paper is to study the influence of contour process parameters, laser power and scanning velocity on the side surface quality of the AlSi10Mg sample. Design/methodology/approach Using L-PBF technology to manufacture AlSi10Mg samples under different contour process parameters, use a laser confocal microscope to capture the surface information of the samples, and obtain the surface roughness Ra and the maximum surface height Rz of each sample after analysis and processing. Findings The results show that the side surface roughness decreases with the increase of the laser power at the fixed scanning velocity of 1,000 mm/s, the side surface roughness Ra stays within the error range as the contour velocity increases. It is found that the Ra increases with the scanning velocity increasing and the greater the laser power with the greater Ra increases when the laser power of contour process parameters is 300 W, 350 W and 400 W. The Rz maintain growth with the contour scanning velocity increasing at constant laser power. The continuous uniform contour covers the pores in the molten pool of the sample edge and thus increase the density of the sample. Two mechanisms named “Active adhesion” and “Passive adhesion” cause sticky powder. Originality/value Formation of a uniform and even contour track is key to obtain the good side surface quality. The side surface quality is determined by the uniformity and stability of the contour track when the layer thickness is fixed. These research results can provide helpful guidance to improve the surface quality of L-PBF manufactured parts.

Single Track Formation during Selective Laser Melting of Ti-6Al-4V Alloy

2019 ◽  
Vol 946 ◽  
pp. 978-983 ◽  
Author(s):  
R.M. Baitimerov
Keyword(s):  
Selective Laser Melting ◽  
Process Parameters ◽  
Complex Shape ◽  
Powder Layer ◽  
Single Track ◽  
Laser Melting ◽  
Additive Manufacturing Technology ◽  
Geometrical Characteristics ◽  
Track Formation ◽  
Point Distance

Selective laser melting (SLM) is an additive manufacturing technology that allows to produce functional parts with extremely complex shape from metal powder feedstock. 240 single tracks with the length of 10 mm were fabricated using different SLM process parameters: laser power output, powder layer thickness, point distance and exposure time. Obtained single tracks were measured using optical microscopy. An influence of SLM process parameters on geometrical characteristics of obtained single tracks was investigated.

scholarly journals The Influence of Process Parameters and Scanning Strategy on Lower Surface Quality of TA15 Parts Fabricated by Selective Laser Melting

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1228
Author(s):  
Junjie Jiang ◽  
Jianming Chen ◽  
Zhihao Ren ◽  
Zhongfa Mao ◽  
Xiangyu Ma ◽  
...  
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Flexible Manufacturing ◽  
Molten Pool ◽  
Lower Surface ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Influence Of Process Parameters

With superior flexible manufacturing capability, selective laser melting (SLM) has attracted more and more attention in the aerospace, medical, and automotive industries. However, the poor quality of the lower surface in overhanging structures is still one of the factors that limits the wide application of SLM. In this work, the influence of process parameters and scanning strategy on the lower surface quality of SLMed TA15 (Ti-6Al-2Zr-1Mo-1V) titanium alloy parts were studied. The results showed that the laser surface energy density (EF) had a significant influence on the quality of the lower surface. Excessive EF led to obvious sinking of the molten pool and a serious slag hanging phenomenon. However, the too low EF easily contributed to the insufficient powder fusion in the lower surface area, which led to the agglomeration of a molten pool during core processing, resulting in slag hanging, pores, and powder spalling that reduced the quality of the lower surface. Moreover, the cross-remelting strategy and non-remelting strategy gained better surface quality at the low EF and high EF, respectively. In addition, it was found that the quality of the lower surface could be quickly and accurately evaluated by the cooling time of the molten pool during the processing of the lower surface. This research can increase the understanding of the forming mechanism of the lower surface and has certain guiding significance for the process optimization of the lower surface.

Influence of Selective Laser Melting Process Parameters on Densification Behavior, Surface Quality and Hardness of 18Ni300 Steel

2020 ◽  
Vol 861 ◽  
pp. 77-82
Author(s):  
Gan Li ◽  
Cheng Guo ◽  
Wen Feng Guo ◽  
Hong Xing Lu ◽  
Lin Ju Wen ◽  
...  
Keyword(s):  
Energy Density ◽  
Relative Density ◽  
Maraging Steel ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
Densification Behavior ◽  
Laser Melting ◽  
Scan Speed

This study investigated the effect of laser power (P), scan speed (v) and hatch space (h) on densification behavior, surface quality and hardness of 18Ni300 maraging steel fabricated by selective laser melting (SLM). The results indicated that the relative density of the SLMed samples has a shape increase from 73% to 97% with the laser energy density increasing from 0.5 to 2.2 J/mm2. The relative density ≥ 99% was achieved at the energy density in the range of 2.2~5.9 J/mm2. The optimum process parameters were found to be laser power of 150~200 W, scan speed of 600mm/s and hatch space of 0.105mm. In addition, it was found that the hardness increased initially with the increasing relative density up to relative density of 90% and then little relationship, but finally increase again significantly. This work provides reference for determining process parameters for SLMed maraging steel and the development of 3D printing of die steels.

Experimental Investigation into the Single-Track of Selective Laser Melting of IN625

2011 ◽  
Vol 233-235 ◽  
pp. 2844-2848 ◽  
Author(s):  
Li Wang ◽  
Qing Song Wei ◽  
Yu Sheng Shi ◽  
Jin Hui Liu ◽  
Wen Ting He
Keyword(s):  
Energy Density ◽  
Relative Density ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Laser Energy ◽  
Scanning Speed ◽  
Single Track ◽  
Laser Melting ◽  
Metallic Parts

Selective laser melting(SLM) is driven by the need to fabricate functional metallic parts and tools with near shape and density. The method of process to fabricate a metal part will save materials, time and energy compared to the traditional manufacturing methods. Unlike the selective laser sintering (SLS), the metal powder particles are molten by the laser beam during the process of selective laser melting. In this paper, IN625 powders were adopted to investigate the characters of single molten track. The factors that affect the surface quality and relative density are the process parameters such as the laser energy, scan speed and so on. They were studied to find out the correlation between the parameters and formation of single-track. It has been found that Optimal ratio between laser power and scanning speed (P/v) is 1-1.5 for IN625 SLM. P/v is the linear energy density. It also has been found that the width and height of single-track can be calculated when the linear energy density is given. In this study the laser power, scan spacing and the hatch spacing which affect the surface quality and the relative density of the metallic parts were optimized.

scholarly journals Selective Laser Melting of Pre-Alloyed NiTi Powder: Single-Track Study and FE Modeling with Heat Source Calibration

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7486
Author(s):  
Stanislav V. Chernyshikhin ◽  
Denis G. Firsov ◽  
Igor V. Shishkovsky
Keyword(s):  
Heat Source ◽  
Thermal Behavior ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
Scanning Speed ◽  
Fe Modeling ◽  
Single Track ◽  
Laser Melting ◽  
Melt Pool

Unique functional properties such as the low stiffness, superelasticity, and biocompatibility of nickel–titanium shape-memory alloys provide many applications for such materials. Selective laser melting of NiTi enables low-cost customization of devices and the manufacturing of highly complex geometries without subsequent machining. However, the technology requires optimization of process parameters in order to guarantee high mass density and to avoid deterioration of functional properties. In this work, the melt pool geometry, surface morphology, formation mode, and thermal behavior were studied. Multiple combinations of laser power and scanning speed were used for single-track preparation from pre-alloyed NiTi powder on a nitinol substrate. The experimental results show the influence of laser power and scanning speed on the depth, width, and depth-to-width aspect ratio. Additionally, a transient 3D FE model was employed to predict thermal behavior in the melt pool for different regimes. In this paper, the coefficients for a volumetric double-ellipsoid heat source were calibrated with bound optimization by a quadratic approximation algorithm, the design of experiments technique, and experimentally obtained data. The results of the simulation reveal the necessary conditions of transition from conduction to keyhole mode welding. Finally, by combining experimental and FE modeling results, the optimal SLM process parameters were evaluated as P = 77 W, V = 400 mm/s, h = 70 μm, and t = 50 μm, without printing of 3D samples.

scholarly journals Optimising the process parameters of selective laser melting for the fabrication of Ti6Al4V alloy

2018 ◽  
Vol 24 (1) ◽  
pp. 150-159 ◽  
Author(s):  
Zhonghua Li ◽  
Ibrahim Kucukkoc ◽  
David Z. Zhang ◽  
Fei Liu
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
High Surface ◽  
Optimum Process ◽  
Laser Melting ◽  
Vertical Side ◽  
Content Type

Purpose Surface roughness is an important evaluation index for industrial components, and it strongly depends on the processing parameters for selective laser molten Ti6Al4V parts. This paper aims to obtain an optimum selective laser melting (SLM) parameter set to improve the surface roughness of Ti6Al4V samples. Design/methodology/approach A response surface methodology (RSM)-based approach is proposed to improve the surface quality of selective laser molten Ti6Al4V parts and understand the relationship between the SLM process parameters and the surface roughness. The main SLM parameters (i.e. laser power, scan speed and hatch spacing) are optimized, and Ti6Al4V parts are manufactured by the SLM technology with no post processes. Findings Optimum process parameters were obtained using the RSM method to minimise the roughness of the top and vertical side surfaces. Obtained parameter sets were evaluated based on their productivity and surface quality performance. The validation tests have been performed, and the results verified the effectivity of the proposed technique. It was also shown that the top and vertical sides must be handled together to obtain better top surface quality. Practical implications The obtained optimum SLM parameter set can be used in the manufacturing of Ti6Al4V components with high surface roughness requirement. Originality/value RSM is used to analyse and determine the optimal combination of SLM parameters with the aim of improving the surface roughness quality of Ti6Al4V components, for the first time in the literature. Also, this is the first study which aims to simultaneously optimise the surface quality of top and vertical sides of titanium alloys.

scholarly journals Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy

2018 ◽  
Vol 106 (4) ◽  
pp. 405
Author(s):  
Tomasz Seramak ◽  
Katarzyna Zasinska ◽  
Michel Mesnard ◽  
Karolina Bednarz ◽  
Paulina Fic ◽  
...  
Keyword(s):  
Energy Density ◽  
Relative Density ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Thermal Stresses ◽  
Laser Melting ◽  
Dimensional Precision ◽  
Scan Time

Selective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive to different degrees for the quality of the final specimen. The results obtained were used to produce prosthetic crowns and bridges. The thermal stresses that appeared resulted in a deflection of the bridges and consequently in a change in design approach.

Sign in / Sign up

Export Citation Format

Share Document