scholarly journals A Fundamental Study on the Transient Stability of Power Systems with High Shares of Solar PV Plants

Electricity ◽  
2020 ◽  
Vol 1 (1) ◽  
pp. 62-86
Author(s):  
Nikhil Kalloe ◽  
Jorrit Bos ◽  
Jose Rueda Torres ◽  
Mart van der Meijden ◽  
Peter Palensky
Keyword(s):  
The Netherlands ◽  
Power Systems ◽  
Large Scale ◽  
Transient Stability ◽  
Short Circuit ◽  
Renewable Energy Sources ◽  
System Stability ◽  
Solar Pv ◽  
Stability Studies ◽  
Fundamental Study

The last decade has seen an immense growth in renewable energy sources such as solar photovoltaic (PV) plants due to environmental concerns. Due to this rapid growth, solar PV plants are starting to have a larger influence on power system stability and thus their dynamic behavior cannot be ignored in stability studies. The lack of well-established models and parameter sets is the primary reason solar PV plants are not modeled with dynamic characteristics. This paper presents a method to define a standard parameter set for representing large-scale and aggregated solar PV plants in stability studies from the perspective of the transmission system operator (TSO). The method takes into account primarily the conditions provided in the grid connection requirements; for illustrative purposes, the connection requirements of the Netherlands are used. Additionally, a relationship defined as short-circuit current (SCC) PV ratio is proposed to estimate the effect of solar PV plants on transient stability. To illustrate the workings of the proposed ratio, the transmission network of the TenneT TSO B.V. in the Netherlands is used. The analysis demonstrated that high values of SCC PV ratio are an indicator that solar PV plants affect the transient stability while low values of SCC PV ratio showed that solar PV plants have minimal effect on the transient stability. Additionally, methods to improve the transient stability are provided which include limiting the operation regions of critical generators, increasing short-circuit ratio by adding a synchronous condenser or static compensator (STATCOM) and decreasing the reactance between the critical synchronous generator and faulted bus.

scholarly journals Instantaneous Power Control Strategy for Voltage Improvement in Power Network Equipped by Wind Generator

2021 ◽  
Vol 54 (1) ◽  
pp. 147-154
Author(s):  
Issam Griche ◽  
Sabir Messalti ◽  
Kamel Saoudi
Keyword(s):  
Power Systems ◽  
Power Control ◽  
Wind Power ◽  
Control Strategy ◽  
Large Scale ◽  
Transient Stability ◽  
Short Circuit ◽  
Dynamical Response ◽  
Instantaneous Power ◽  
Wide Range

The uncertainty of wind power brings great challenges to large-scale wind power integration. The conventional integration of wind power is difficult to adapt the demand of power grid planning and operation. This paper proposes an instantaneous power control strategy for voltage improvement in power networks using wind turbine improving the dynamical response of power systems performances (voltage and transient stability) after fault. In which the proposed control algorithm based on a new advanced control strategy to control the injected wind power into power system. The efficiency of developed control strategy has been tested using IEEE 9 Bus. Simulation results have showed that the proposed method perform better to preserve optimal performances over wide range of disturbances for both considered scenarios studied short circuit and variable loads.

Microgrids Emergency Control and Protection

2013 ◽  
Vol 2 (1) ◽  
pp. 78-100 ◽  
Author(s):  
Hassan Bevrani ◽  
Mehrdad Gholami ◽  
Neda Hajimohammadi
Keyword(s):  
Power Systems ◽  
Large Scale ◽  
Reactive Power ◽  
Renewable Energy Sources ◽  
Voltage Regulation ◽  
System Stability ◽  
Stable Operation ◽  
Energy Storage Devices ◽  
Control Plan ◽  
Emergency Control

Economical harvesting of electrical energy on a large scale considering the environmental issues is a challenge. As a solution, Microgrids (MGs) promise to facilitate the widely penetration of renewable energy sources (RESs) and energy storage devices into the power systems, reduce system losses and greenhouse gas emissions, and increase the reliability of the electricity supply to the customers. Although the concept of MG is already established, the control strategies and energy management systems for MGs which cover power interchange, system stability, frequency and voltage regulation, active and reactive power control, islanding detection, grid synchronization, following contingencies and emergency conditions are still under development. Like a conventional power system, a Micro-grid (MG) needs emergency control and protection schemes to have secure and stable operation. Since MG can operate in both grid-connected and islanded mode, in addition to the control loops and protection schemes, extra issues must be considered. Transition between two operation modes requires an extra control plan to eliminate and stabilize transients due to mode changing. This paper presents an overview of the key issues and new challenges on emergency control and protection plans in the MG systems. The most important emergency control and protection schemes such as load shedding methods that have been presented over the past years are summarized.

scholarly journals A New Tool to Assess Maximum Permissible Solar PV Penetration in a Power System

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8529
Author(s):  
Dhanuja Lekshmi J ◽  
Zakir Hussain Rather ◽  
Bikash C Pal
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
Unit Commitment ◽  
Renewable Energy Sources ◽  
Research Work ◽  
Clean Energy ◽  
Solar Pv ◽  
System Operator ◽  
Pv Penetration

With diminishing fossil fuel resources and increasing environmental concerns, large-scale deployment of Renewable Energy Sources (RES) has accelerated the transition towards clean energy systems, leading to significant RES generation share in power systems worldwide. Among different RES, solar PV is receiving major focus as it is most abundant in nature compared to others, complimented by falling prices of PV technology. However, variable, intermittent and non-synchronous nature of PV power generation technology introduces several technical challenges, ranging from short-term issues, such as low inertia, frequency stability, voltage stability and small signal stability, to long-term issues, such as unit commitment and scheduling issues. Therefore, such technical issues often limit the amount of non-synchronous instantaneous power that can be securely accommodated by a grid. In this backdrop, this research work proposes a tool to estimate maximum PV penetration level that a given power system can securely accommodate for a given unit commitment interval. The proposed tool will consider voltage and frequency while estimating maximum PV power penetration of a system. The tool will be useful to a system operator in assessing grid stability and security under a given generation mix, network topology and PV penetration level. Besides estimating maximum PV penetration, the proposed tool provides useful inputs to the system operator which will allow the operator to take necessary actions to handle high PV penetration in a secure and stable manner.

scholarly journals Frequency response analysis under faults in weak power systems

2022 ◽  
Vol 12 (2) ◽  
pp. 1077
Author(s):  
Marino Godoy Arcia ◽  
Zaid Garcia Sanchez ◽  
Hernan Hernandez Herrera ◽  
José Antonio Gonzalez Cueto Cruz ◽  
Jorge Iván Silva Ortega ◽  
...  
Keyword(s):  
Power Systems ◽  
Frequency Response ◽  
Transient Stability ◽  
Short Circuit ◽  
Renewable Energy Sources ◽  
Distribution Networks ◽  
Environmental Benefits ◽  
Response Analysis ◽  
Response Factors ◽  
Frequency Fluctuations

The renewable energy sources (RESs) projects are solutions with environmental benefits that are changing the traditional power system operation and concept. Transient stability analysis has opened new research trends to guarantee a secure operation high penetration. Problems such as frequency fluctuations, decoupling between generator angular speed, network frequency fluctuation and kinetic energy storing absence are the main non-conventional RESs penetration in power systems. This paper analyzes short-circuit influence on frequency response, focusing on weak distribution networks and isolated, to demonstrate relevance in frequency stability. A study case considered a generation outage and a load input to analyze frequency response. The paper compares frequency response during a generation outage with a short-circuit occurrence. In addition, modular value and angle generator terminal voltage affectation by electric arc and network ratio R⁄X, failure type influence in power delivered behavior, considering fault location, arc resistance and load. The arc resistance is defined as an added resistance that appears during failure and influences voltage modulus and angle value results showing that intermittent non-conventional RES participation can lead to frequency fluctuations. Results showed that arc resistance, type of failure, location and loadability determine the influence of frequency response factors in weak power systems.

A Descriptive Approach for Power System Stability and Security Assessment

2013 ◽  
pp. 1527-1545
Author(s):  
A. G. Tikdari ◽  
H. Bevrani ◽  
G. Ledwich
Keyword(s):  
Power Systems ◽  
Power System ◽  
Large Scale ◽  
Renewable Energy Sources ◽  
Control Measures ◽  
System Stability ◽  
Security Assessment ◽  
Electrical Measurements ◽  
Emergency Control ◽  
Bus Voltage

Power system dynamic analysis and security assessment are becoming more significant today due to increases in size and complexity from restructuring, emerging new uncertainties, integration of renewable energy sources, distributed generation, and micro grids. Precise modeling of all contributed elements/devices, understanding interactions in detail, and observing hidden dynamics using existing analysis tools/theorems are difficult, and even impossible. In this chapter, the power system is considered as a continuum and the propagated electromechanical waves initiated by faults and other random events are studied to provide a new scheme for stability investigation of a large dimensional system. For this purpose, the measured electrical indices (such as rotor angle and bus voltage) following a fault in different points among the network are used, and the behavior of the propagated waves through the lines, nodes, and buses is analyzed. The impact of weak transmission links on a progressive electromechanical wave using energy function concept is addressed. It is also emphasized that determining severity of a disturbance/contingency accurately, without considering the related electromechanical waves, hidden dynamics, and their properties is not secure enough. Considering these phenomena takes heavy and time consuming calculation, which is not suitable for online stability assessment problems. However, using a continuum model for a power system reduces the burden of complex calculations. Finally, a new power system emergency control framework based on descriptive study of electrical measurements and electromechanical wave propagation in large electric power systems is introduced. Since, fast and accurate detection of instability is essential in initiating certain emergency control measures, the proposed methodology could be also useful to detect the contingency condition and performing the well-known islanding and load shedding techniques. The chapter is supplemented by some illustrative nonlinear simulations on large scale test systems.

Effect of Wind Farm on Transient and Small-Signal Stability Based on BPA

2013 ◽  
Vol 860-863 ◽  
pp. 309-313
Author(s):  
Xiao Yan Bian ◽  
Li Ning Yang ◽  
Xin Xin Huang ◽  
Yang Fu
Keyword(s):  
Power System ◽  
Large Scale ◽  
Wind Farm ◽  
Transient Stability ◽  
Short Circuit ◽  
System Stability ◽  
Small Signal ◽  
Small Signal Stability ◽  
Signal Stability ◽  
Three Phase

Large scale wind farm output variation always deteriorates the system stability. To study this problem, this paper builds the model of power system with the integration of large-scale wind farm based on BPA. The simulation results show that large oscillations of voltage and rotor angle of system will happen, when three-phase short circuit fault occurs on the main line for transmitting wind power. With wind farm output decreasing, the transient stability and small-signal stability of power system will be improved.

scholarly journals Voltage Stability of Power Systems with Renewable-Energy Inverter-Based Generators: A Review

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 115
Author(s):  
Nasser Hosseinzadeh ◽  
Asma Aziz ◽  
Apel Mahmud ◽  
Ameen Gargoom ◽  
Mahbub Rabbani
Keyword(s):  
Renewable Energy ◽  
Power Systems ◽  
Voltage Stability ◽  
Reactive Power ◽  
Power Grid ◽  
Renewable Energy Sources ◽  
Electrical Power ◽  
System Stability ◽  
Special Issue ◽  
Synchronous Generators

The main purpose of developing microgrids (MGs) is to facilitate the integration of renewable energy sources (RESs) into the power grid. RESs are normally connected to the grid via power electronic inverters. As various types of RESs are increasingly being connected to the electrical power grid, power systems of the near future will have more inverter-based generators (IBGs) instead of synchronous machines. Since IBGs have significant differences in their characteristics compared to synchronous generators (SGs), particularly concerning their inertia and capability to provide reactive power, their impacts on the system dynamics are different compared to SGs. In particular, system stability analysis will require new approaches. As such, research is currently being conducted on the stability of power systems with the inclusion of IBGs. This review article is intended to be a preface to the Special Issue on Voltage Stability of Microgrids in Power Systems. It presents a comprehensive review of the literature on voltage stability of power systems with a relatively high percentage of IBGs in the generation mix of the system. As the research is developing rapidly in this field, it is understood that by the time that this article is published, and further in the future, there will be many more new developments in this area. Certainly, other articles in this special issue will highlight some other important aspects of the voltage stability of microgrids.

scholarly journals Rooftop Solar PV Penetration Impacts on Distribution Network and Further Growth Factors—A Comprehensive Review

Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 55
Author(s):  
Busra Uzum ◽  
Ahmet Onen ◽  
Hany M. Hasanien ◽  
S. M. Muyeen
Keyword(s):  
Solar Energy ◽  
Power Quality ◽  
Distribution System ◽  
Renewable Energy Sources ◽  
Distribution Network ◽  
System Stability ◽  
Solar Pv ◽  
Voltage Quality ◽  
Solution Methods ◽  
Pv Penetration

In order to meet the electricity needs of domestic or commercial buildings, solar energy is more attractive than other renewable energy sources in terms of its simplicity of installation, less dependence on the field and its economy. It is possible to extract solar energy from photovoltaic (PV) including rooftop, ground-mounted, and building integrated PV systems. Interest in rooftop PV system applications has increased in recent years due to simple installation and not occupying an external area. However, the negative effects of increased PV penetration on the distribution system are troublesome. The power loss, reverse power flow (RPF), voltage fluctuations, voltage unbalance, are causing voltage quality problems in the power network. On the other hand, variations in system frequency, power factor, and harmonics are affecting the power quality. The excessive PV penetration also the root cause of voltage stability and has an adverse effect on protection system. The aim of this article is to extensively examines the impacts of rooftop PV on distribution network and evaluate possible solution methods in terms of the voltage quality, power quality, system protection and system stability. Moreover, it is to present a comparison of the advantages/disadvantages of the solution methods discussed, and an examination of the solution methods in which artificial intelligence, deep learning and machine learning based optimization and techniques are discussed with common methods.

scholarly journals A Novel Methodology for Adaptive Coordination of Multiple Controllers in Electrical Grids

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1474
Author(s):  
Ruben Tapia-Olvera ◽  
Francisco Beltran-Carbajal ◽  
Antonio Valderrabano-Gonzalez ◽  
Omar Aguilar-Mejia
Keyword(s):  
Power Systems ◽  
Power System ◽  
Electric Power ◽  
Large Scale ◽  
Short Circuit ◽  
Dynamic Performance ◽  
Low Frequency ◽  
Electric Power System ◽  
Design Stage ◽  
Positive Interaction

This proposal is aimed to overcome the problem that arises when diverse regulation devices and controlling strategies are involved in electric power systems regulation design. When new devices are included in electric power system after the topology and regulation goals were defined, a new design stage is generally needed to obtain the desired outputs. Moreover, if the initial design is based on a linearized model around an equilibrium point, the new conditions might degrade the whole performance of the system. Our proposal demonstrates that the power system performance can be guaranteed with one design stage when an adequate adaptive scheme is updating some critic controllers’ gains. For large-scale power systems, this feature is illustrated with the use of time domain simulations, showing the dynamic behavior of the significant variables. The transient response is enhanced in terms of maximum overshoot and settling time. This is demonstrated using the deviation between the behavior of some important variables with StatCom, but without or with PSS. A B-Spline neural networks algorithm is used to define the best controllers’ gains to efficiently attenuate low frequency oscillations when a short circuit event is presented. This strategy avoids the parameters and power system model dependency; only a dataset of typical variable measurements is required to achieve the expected behavior. The inclusion of PSS and StatCom with positive interaction, enhances the dynamic performance of the system while illustrating the ability of the strategy in adding different controllers in only one design stage.

scholarly journals Predicting AC Optimal Power Flows: Combining Deep Learning and Lagrangian Dual Methods

2020 ◽  
Vol 34 (01) ◽  
pp. 630-637 ◽  
Author(s):  
Ferdinando Fioretto ◽  
Terrence W.K. Mak ◽  
Pascal Van Hentenryck
Keyword(s):  
Deep Learning ◽  
Power Systems ◽  
Power Flow ◽  
Optimal Power Flow ◽  
Large Scale ◽  
Renewable Energy Sources ◽  
Electrical Power ◽  
Practical Applications ◽  
Fundamental Building Block ◽  
Optimal Power

The Optimal Power Flow (OPF) problem is a fundamental building block for the optimization of electrical power systems. It is nonlinear and nonconvex and computes the generator setpoints for power and voltage, given a set of load demands. It is often solved repeatedly under various conditions, either in real-time or in large-scale studies. This need is further exacerbated by the increasing stochasticity of power systems due to renewable energy sources in front and behind the meter. To address these challenges, this paper presents a deep learning approach to the OPF. The learning model exploits the information available in the similar states of the system (which is commonly available in practical applications), as well as a dual Lagrangian method to satisfy the physical and engineering constraints present in the OPF. The proposed model is evaluated on a large collection of realistic medium-sized power systems. The experimental results show that its predictions are highly accurate with average errors as low as 0.2%. Additionally, the proposed approach is shown to improve the accuracy of the widely adopted linear DC approximation by at least two orders of magnitude.

Sign in / Sign up

Export Citation Format

Share Document