scholarly journals Design of Dual Ultra–Wideband Band–Pass Filter Using Stepped Impedance Resonator λg/4 Short Stubs and T–Shaped Band-Stop Filter

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1951
Author(s):  
Kicheol Yoon ◽  
Kwanggi Kim
Keyword(s):  
Wireless Communication ◽  
Insertion Loss ◽  
Communication Systems ◽  
Dual Band ◽  
Wireless Communication Systems ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Stop Filter ◽  
Band Pass ◽  
Stepped Impedance Resonator

Portable wireless communication systems are increasingly in demand in small sizes for human convenience. In wireless communication systems, the performance, size, and unit cost are very important. A band−pass filter is important to sharp cut–off frequency characteristics, size, and frequency selectivity in wireless communication systems. The band−pass filter has three types of techniques in the transmission−zero method, stub−loaded resonator, and stepped impedance resonator for the sharp cut−off frequency characteristic, adjustable bandwidth, and excellent frequency response characteristics. To obtain these characteristics, the impedance ratio and length of a stub are mainly adjusted. It also utilizes a multi–mode technique to increase bandwidth. However, it is analyzed that the problem of reducing the size of the device still remains. To solve these problems, the paper is applied to a stub−loaded resonator and a stepped impedance resonator to control the impedance ratio and the length of the stub to obtain the results of the transmission−zero method, bandwidth control, and size reduction through the folded structure. Dual−band bandwidth was secured by integrating a T−shaped band−stop filter. The designed band–pass filter has center frequencies of 243 GHz and 7.49 GHz, and the insertion loss of a proposed band−pass filter is 0.102 dB and 0.103 dB. Additionally, the return loss of a proposed band−pass filter is 19.13 dB and 19.96 dB, respectively. The bandwidth of a filter is 120% and 105%, respectively. The size of the filter is 0.0708 λg × 0.0533 λg. The designed filter has a good skirt phenomenon, small size, low insertion loss, and dual−band characteristics.

scholarly journals Study of Microstrip Dual-Band Band Pass Filter

2021 ◽  
Author(s):  
Anciline V ◽  
Maheswari S
Keyword(s):  
Wireless Communication ◽  
Insertion Loss ◽  
Communication System ◽  
Dual Band ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Wireless Communication System ◽  
Band Pass ◽  
Main Component

The main component widely used in wireless communication system is dual-band band pass filter. This band pass filter is intended in many ways and some are microstrip, waveguide, etc. The dual-band will works in two different frequency ranges which will provide a huge application. This paper compares different microstrip dual-band band pass filter based on the techniques, insertion loss, frequency, etc.

scholarly journals Dual band Stepped Impedance Interdigital Microstrip Filter for LTE Bands

2019 ◽  
Vol 4 (7) ◽  
pp. 28-30
Author(s):  
William Johnson ◽  
Cavin Roger Nunes ◽  
Savio Sebastian Dias ◽  
Siddhi Suresh Parab ◽  
Varsha Shantaram Hatkar
Keyword(s):  
Insertion Loss ◽  
Bandpass Filter ◽  
Dual Band ◽  
Band Pass Filter ◽  
Coupled Resonators ◽  
Microstrip Filter ◽  
Resonant Frequencies ◽  
Pass Filter ◽  
Band Pass ◽  
Low Insertion Loss

In this paper, a dual band microstrip bandpass filter has been proposed utilizing three edge coupled resonators, interdigital stubs and DGS technique. To enhance the coupling degree, two interdigital coupled feed lines are employed in this filter. The suppressing cell consists of stepped impedance ladder type resonators, which provides a wide stopband. The proposed suppressing cell has clear advantages like low insertion loss in the passband and suitable roll off. The frequency response of the filter looks like a standard dual band band-pass filter. The filter exhibits a dual passband with resonant frequencies at 2.2GHz and 3.45GHz covers LTE1 and LTE22 bands.

scholarly journals Design of Complementary Hexagonal Metamaterial Based HMSIW Band-Pass Filter and Reconfigurable SIW Filter Using PIN Diodes

2021 ◽  
Vol 10 (2) ◽  
pp. 19-26
Author(s):  
H. Boubakar ◽  
M. Abri ◽  
M. Benaissa
Keyword(s):  
Insertion Loss ◽  
Filter Design ◽  
Dual Band ◽  
Band Pass Filter ◽  
Pin Diodes ◽  
Pass Filter ◽  
Transmission Bandwidth ◽  
Band Pass ◽  
Very High

This paper is divided into two sections, in the first section, a new SIW and a half-mode SIW band-pass filters based on complementary hexagonal metamaterial cells (C-HMCs) are proposed. Firstly, the SIW is analyzed in case of using two C-HMC cells and in the case of using four of these cells.  Secondly, the HMSIW tunable BPF is studied and optimized. The size of the half mode is reduced by almost 50%. This filter design has a very high insertion loss about -0.4 dB, and significant transmission bandwidth extending from 5.9 GHz to 6.5 GHz. In the second section of this paper, an electronically reconfigurable SIW band-pass filter is proposed. By implementing two PIN diodes in the gaps of the two C-HMC, the results of turning the diodes ON or OFF individually is a switching in the frequency center, between 5.8 GHz and 6.8 GHz. Also, a dual band with two frequency centers at (5.6 GHz and 7.4 GHz) is achieved by turning both of the diodes ON. In addition, the metamaterial properties of all the proposed filters are investigated and presented in this work.

scholarly journals A Codesigned Compact Dual-Band Filtering Antenna with PIN Loaded for WLAN Applications

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Shanxiong Chen ◽  
Yu Zhao ◽  
Maoling Peng ◽  
Yunji Wang
Keyword(s):  
Communication Systems ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Antenna System ◽  
Dual Band ◽  
Pin Diode ◽  
Area Network ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Pass

A codesigned compact dual-band filtering antenna incorporating a PIN diode for 2.45/5.2 GHz wireless local area network (WLAN) applications is proposed in this paper. The integrated filtering antenna system consists of a simple monopole radiator, a microstrip dual-band band-pass filter, and a PIN diode. The performance of the filtering antenna is notably promoted by optimizing the impedance between the antenna and the band-pass filter, with good selectivity and out-of-band rejection. The design process follows the approach of the synthesis of band-pass filter. In addition, the PIN diode is incorporated in the filtering antenna for further size reduction, which also widens the coverage of the bandwidth by about 230% for 2.4 GHz WLAN. With the presence of small size and good filtering performances, the proposed filtering antenna is a good candidate for the wireless communication systems. Prototypes of the proposed filtering antenna incorporating a PIN diode are fabricated and measured. The measured results including return losses and radiation patterns are presented.

scholarly journals Design of dual-mode SIR bandpass filter based on shorting pin for wireless communication applications

2020 ◽  
Vol 18 (3) ◽  
pp. 1375
Author(s):  
Jenan Ayad Namiq ◽  
Mustafa A. Jalil
Keyword(s):  
Wireless Communication ◽  
Bandpass Filter ◽  
Band Pass Filter ◽  
Dual Mode ◽  
Coupled Line ◽  
Pass Filter ◽  
Shorting Pin ◽  
Band Pass ◽  
Stepped Impedance Resonator ◽  
Insertion Losses

<p id="docs-internal-guid-6a9909c3-7fff-4ac4-3e3a-a2f823e1246f" dir="ltr"><span>A new design of microstrip dual mode band-pass-filter (BPF) by using stepped impedance resonator (SIR) based on shorting pin is proposed. The designed structure use two U-shaped tri-sections SIR resonators coupled to each other and a two coupled line feeding ports each of 50 ohm impedance. Shorting pins are used to excite the upper frequency passband in the re   sponse of the filter due to current distribution perturbation at the locations of the shorting pins.  For demonstration, WLAN (5.2-5.7 GHz) and GSM (1.85-1.99 GHz) and Advanced Wireless Services (AWS) (1.71-1.755 GHz). The return losses are -32.469 dB and -26.18 dB respectively at the operating frequencies of the filter.  The results of  insertion losses of the filter is 0.37 and 0.24 dB during the operating bands and more than 25 dB which consider a good out-of- band rejection. </span></p>

scholarly journals W‐band dual‐band waveguide band‐pass filter using dual‐mode cavities

2018 ◽  
Vol 54 (25) ◽  
pp. 1444-1446
Author(s):  
Jianfei Chen ◽  
Sheng Zhang ◽  
Chao Zhang ◽  
Yuehua Li
Keyword(s):  
Dual Band ◽  
Band Pass Filter ◽  
Dual Mode ◽  
Pass Filter ◽  
W Band ◽  
Band Pass

scholarly journals Design and Realization of Band Pass Filter in K-Band Frequency for Short Range Radar Application

2021 ◽  
Vol 21 (1) ◽  
pp. 1
Author(s):  
Arie Setiawan ◽  
Taufiqqurrachman Taufiqqurrachman ◽  
Adam Kusumah Firdaus ◽  
Fajri Darwis ◽  
Aminuddin Rizal ◽  
...  
Keyword(s):  
Insertion Loss ◽  
Short Range ◽  
Return Loss ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Frequency ◽  
Measurement Results ◽  
Band Pass ◽  
Bandwidth Analysis ◽  
K Band

Short range radar (SRR) uses the K-band frequency range in its application. The radar requires high-resolution, so the applied frequency is 1 GHz wide. The filter is one of the devices used to ensure only a predetermined frequency is received by the radar system. This device must have a wide operating bandwidth to meet the specification of the radar. In this paper, a band pass filter (BPF) is proposed. It is designed and fabricated on RO4003C substrate using the substrate integrated waveguide (SIW) technique, results in a wide bandwidth at the K-band frequency that centered at 24 GHz. Besides the bandwidth analysis, the analysis of the insertion loss, the return loss, and the dimension are also reported. The simulated results of the bandpass filter are: VSWR of 1.0308, a return loss of -36.9344 dB, and an insertion loss of -0.6695 dB. The measurement results show that the design obtains a VSWR of 2.067, a return loss of -8.136 dB, and an insertion loss of -4.316  dB. While, it is obtained that the bandwidth is reduced by about 50% compared with the simulation. The result differences between simulation and measurement are mainly due to the imperfect fabrication process.

scholarly journals Effect of the defected microstrip structure shapes on the performance of dual-band bandpass filter for wireless communications

2021 ◽  
Vol 10 (1) ◽  
pp. 232-240
Author(s):  
Mussa Mabrok ◽  
Zahriladha Zakaria ◽  
Yully Erwanti Masrukin ◽  
Tole Sutikno ◽  
Hussein Alsariera
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
Bandpass Filter ◽  
Dual Band ◽  
Center Frequency ◽  
Wireless Communication Systems ◽  
Notch Band ◽  
Quarter Wavelength ◽  
Crucial Component ◽  
Microstrip Structure

Due to the progression growth of multiservice wireless communication systems in a single device, multiband bandpass filter has attract a great attention to the end user. Therefore, multiband bandpass filter is a crucial component in the multiband transceivers systems which can support multiple services in one device. This paper presents a design of dual-band bandpass filter at 2.4 GHz and 3.5 GHz for WLAN and WiMAX applications. Firstly, the wideband bandpass filter is designed at a center frequency of 3 GHz based on quarter-wavelength short circuited stub. Three types of defected microstrip structure (DMS) are implemented to produce a wide notch band, which are T-inversed shape, C-shape, and U- Shape. Based on the performance comparisons, U-shaped DMS is selected to be integrated with the bandpass filter. The designed filter achieved two passbands centered at 2.51 GHz and 3.59 GHz with 3 dB bandwidth of 15.94 % and 15.86 %. The proposed design is very useful for wireless communication systems and its applications such as WLAN and WiMAX 

Sign in / Sign up

Export Citation Format

Share Document