scholarly journals Analytical Study of the Electrical Output Characteristics of c-Si Solar Cells by Cut and Shading Phenomena

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3397 ◽  
Author(s):  
Jong Lim ◽  
Woo Shin ◽  
Hyemi Hwang ◽  
Young-Chul Ju ◽  
Suk Ko ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Incident Light ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Si Solar Cell ◽  
Si Solar Cells ◽  
Electrical Output

Cut solar cells have received considerable attention recently as they can reduce electrical output degradation when the c-Si solar cells (crystalline-silicon solar cells) are shaded. Cut c-Si solar cells have a lower short-circuit current than normal solar cells and the decrease in short-circuit currents is similar to the shading effect of c-Si solar cells. However, the results of this study’s experiment show that the shadow effect of a c-Si solar cell reduces the V o c (open circuit voltage) in the c-Si solar cell but the V o c does not change when the c-Si solar cell is cut because the amount of incident light does not change. In this paper, the limitations of the electrical power analysis of the cut solar cells were identified when only photo current was considered and the analysis of the electric output of the cut c-Si solar cells was interpreted with a method different from that used in previous analyses. Electrical output was measured when the shaded and cut rates of c-Si solar cells were increased from 0% to 25, 50 and 75%, and a new theoretical model was compared with the experimental results using MATLAB.

scholarly journals Improvement of short circuit current of mono crystalline silicon solar cells

2013 ◽  
Vol 16 (1) ◽  
pp. 48-56
Author(s):  
Vu Ngoc Hoang ◽  
Linh Ngoc Tran ◽  
Lan Truong ◽  
Khoa Thanh Nhat Phan ◽  
Chien Mau Dang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Indium Tin Oxide ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Front Surface ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Crystalline Silicon Solar Cell ◽  
Antireflection Coatings

In this report we present series of experiments during which the short circuit current of mono crystalline silicon solar cell was improved step by step so as a consequence the efficiency was increased. At first, the front contact of solar cell was optimized to reduce the shadow loss and the series resistance. Then surface treatments were prepared by TMAH solution to reduce the total light reflectance and to improve the light trapping effect. Finally, antireflection coatings were deposited to passivate the front surface either by silicon nitride thin layer or to increase the collection probability by indium tin oxide layer, and to reduce the reflectance of light. As a result, solar cells of about 13% have been obtained, with the average open circuit voltage Voc about 527mV, with the fill factor about 68% and the short circuit current about 7.92 mA/cm2 under the irradiation density of 21 mW/cm2.

Photovoltaic Characteristics of Ultra-Thin Single Crystalline Silicon Solar Cells

2016 ◽  
Vol 25 (01n02) ◽  
pp. 1640008
Author(s):  
R. Miyazawa ◽  
H. Wakabayashi ◽  
K. Tsutsui ◽  
H. Iwai ◽  
K. Kakushima
Keyword(s):  
Solar Cells ◽  
Crystalline Silicon ◽  
Spectral Response ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Response Measurement ◽  
Single Crystalline ◽  
Si Solar Cells ◽  
Photovoltaic Characteristics

Photovoltaic characteristics of ultra-thin single crystalline Si solar cells with thicknesses ranging from 7.6 to 3.3 nm are presented. While the short-circuit current (ISC) AM1.5 illumination has shown a linear relationship with the volume of the Si layer, a gradual increase in the open-circuit voltage (VOC) with thinner Si layer has been confirmed, implying the bandgap enlargement of the Si layer due to quantum confinement. Spectral response measurement has revealed an increased optical bandgap of 1.3 eV for 3.3-nm-thick Si solar cells, which is wider than that of 7.6-nm-thick Si ones. Although some process related issues have become clear during the fabrication of solar cells, they can be utilized as top cells for tandem configurations, exceeding the limit of the bulk Si solar cells.

Measured and Simulated Temperature Dependence of A-Si:H Solar Cell Parameters

1996 ◽  
Vol 426 ◽  
Author(s):  
H. Stiebig ◽  
Th. Eickhoff ◽  
J. Zimmer ◽  
C. Beneking ◽  
H. Wagner
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Temperature Dependence ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Cell Parameters ◽  
Crystalline Silicon Solar Cells ◽  
Device Modelling

AbstractIn contrast to the successful application of analytic equations to the current-voltage behaviour of crystalline silicon solar cells in the dark and under AM1.5 illumination, the description of a-Si:H solar cells parameters requires device modelling concepts taking the full set of semiconductor equations into account. This in particular holds for the explanation of the temperature dependence (225–400K) of experimentally determined a-Si:H p-i-n solar cell parameters. Device modelling calculations show that the observed decrease of the short circuit current at AM 1.5 with lower T is much more effected by the additional charge trapped in the tail states and recharging of defect states than by the broadening of the gap. The induced electric field distortion blocks the extraction of photo generated holes. The open circuit voltage Voc increases with lower T which is caused by the same trapping effect.

Measured and Simulated Temperature Dependence of A-Si:H Solar Cell Parameters

1996 ◽  
Vol 420 ◽  
Author(s):  
H. Stiebig ◽  
Th. Eickhoff ◽  
J. Zimmer ◽  
C. Beneking ◽  
H. Wagner
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Temperature Dependence ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Cell Parameters ◽  
Crystalline Silicon Solar Cells ◽  
Device Modelling

AbstractIn contrast to the successful application of analytic equations to the current-voltage behaviour of crystalline silicon solar cells in the dark and under AM 1.5 illumination, the description of a-Si:H solar cells parameters requires device modelling concepts taking the full set of semiconductor equations into account. This in particular holds for the explanation of the temperature dependence (225-400K) of experimentally determined a-Si:H p-i-n solar cell parameters. Device modelling calculations show that the observed decrease of the short circuit current at AM 1.5 with lower T is much more effected by the additional charge trapped in the tail states and recharging of defect states than by the broadening of the gap. The induced electric field distortion blocks the extraction of photo generated holes. The open circuit voltage Voc increases with lower T which is caused by the same trapping effect.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals GaInP/GaAs/poly-Si Multi-Junction Solar Cells by in Metal Balls Bonding

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 726
Author(s):  
Ray-Hua Horng ◽  
Yu-Cheng Kao ◽  
Apoorva Sood ◽  
Po-Liang Liu ◽  
Wei-Cheng Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Low Temperature ◽  
Triple Junction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Metal Line ◽  
Solar Simulator ◽  
Junction Solar Cell

In this study, a mechanical stacking technique has been used to bond together the GaInP/GaAs and poly-silicon (Si) solar wafers. A GaInP/GaAs/poly-Si triple-junction solar cell has mechanically stacked using a low-temperature bonding process which involves micro metal In balls on a metal line using a high-optical-transmission spin-coated glue material. Current–voltage measurements of the GaInP/GaAs/poly-Si triple-junction solar cells have carried out at room temperature both in the dark and under 1 sun with 100 mW/cm2 power density using a solar simulator. The GaInP/GaAs/poly-Si triple-junction solar cell has reached an efficiency of 24.5% with an open-circuit voltage of 2.68 V, a short-circuit current density of 12.39 mA/cm2, and a fill-factor of 73.8%. This study demonstrates a great potential for the low-temperature micro-metal-ball mechanical stacking technique to achieve high conversion efficiency for solar cells with three or more junctions.

Study of Photoelectrochemical Solar Cell Using WSe2 Crystal

2013 ◽  
Vol 665 ◽  
pp. 330-335 ◽  
Author(s):  
Ripal Parmar ◽  
Dipak Sahay ◽  
R.J. Pathak ◽  
R.K. Shah
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Fill Factor ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Energy ◽  
Open Circuit ◽  
Cell Parameters ◽  
Photoelectrochemical Solar Cell ◽  
Photoelectrochemical Solar Cells

The solar cells have been used as most promising device to convert light energy into electrical energy. In this paper authors have attempted to fabricate Photoelectrochemical solar cell with semiconductor electrode using TMDCs. The Photoelectrochemical solar cells are the solar cells which convert the solar energy into electrical energy. The photoelectrochemical cells are clean and inexhaustible sources of energy. The photoelectrochemical solar cells are fabricated using WSe2crystal and electrolyte solution of 0.025M I2, 0.5M NaI, 0.5M Na2SO4. Here the WSe2crystals were grown by direct vapour transport technique. In our investigations the solar cell parameters like short circuit current (Isc) and Open circuit voltage (Voc) were measured and from that Fill factor (F.F.) and photoconversion efficiency (η) are investigated. The results obtained shows that the value of efficiency and fill factor of solar cell varies with the illumination intensities.

HIT Solar Cell With V2Ox Window Layer

MRS Advances ◽  
2017 ◽  
Vol 2 (53) ◽  
pp. 3147-3156 ◽  
Author(s):  
Erenn Ore ◽  
Gehan Amaratunga ◽  
Stefaan De Wolf
Keyword(s):  
Solar Cell ◽  
Physical Vapor Deposition ◽  
Crystalline Silicon ◽  
Layer Structure ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Window Layer ◽  
Limiting Factors ◽  
Vapor Deposition Technique

ABSTRACTIn the conventional crystalline silicon heterojunction solar cell with the intrinsic thin layer structure (the HIT solar cell), a p-doped thin film silicon or its alloy (pDTF-Si/A) is used as the hole collecting window layer. However, the parasitic absorbance in the pDTF-Si/A window layer, and the toxic, explosive diborane gas used for p-doping are limiting factors for achieving HIT cells with reduced processing costs and / or higher efficiencies. In this work, pDTF-Si/A is replaced by V2Ox, which is deposited by a simple physical vapor deposition technique. Due to the wide band gap of V2Ox, the HIT solar cell with the V2Ox window layer generates a higher short-circuit current density than the reference conventional HIT cell under 1 sun, and achieves an open-circuit voltage of 0.7 V. Furthermore, the charge carrier lifetime and pseudo-efficiency values of the HIT solar cell with the V2Ox window layer indicate that this cell has the potential to outperform the conventional HIT cell in terms of the power conversation efficiency under the standard test conditions.

Preparation of the Three Main Layers of CdS/CdTe Thin Film Solar Cells Using a Single Vacuum System

2011 ◽  
Vol 378-379 ◽  
pp. 601-605 ◽  
Author(s):  
Saleh N. Alamri ◽  
M. S. Benghanem ◽  
A. A. Joraid
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Silica ◽  
Vacuum System ◽  
Cdte Thin Film

This study investigates the preparation of the three main layers of a CdS/CdTe thin film solar cell using a single vacuum system. A Close Space Sublimation System was constructed to deposit CdS, CdTe and CdCl2 solar cell layers. Two hot plates were used to heat the source and the substrate. Three fused silica melting dishes were used as containers for the sources. The properties of the deposited CdS and CdTe films were determined via Atomic force microscopy, scanning electron microscopy, X-ray diffraction and optical transmission spectroscopy. An J-V characterization of the fabricated CdS/CdTe solar cells was performed under solar radiation. The short-circuit current density, Jsc, the open-circuit voltage, Voc, fill factor, FF and conversion efficiency, η, were measured and yielded values of 27 mA/cm2, 0.619 V, 58% and 9.8%, respectively.

Photoelectrical and Photovoltaic Peroperties of n-ZnO/p-Si Heterojunction

2011 ◽  
Vol 399-401 ◽  
pp. 1477-1480
Author(s):  
Yan Li Xu ◽  
Jin Hua Li
Keyword(s):  
Solar Cell ◽  
Silicon Solar Cell ◽  
Ion Beam ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Textured Surface ◽  
Si Solar Cell ◽  
The One ◽  
P Type

n-ZnO thin films doped In with 2 atm.% were deposited on p-type silicon wafer with textured surface by Ion Beam Enhanced Deposition method, after annealing and prepared front and back electrodes, the n-ZnO/p-Si heterojunction samples were fabricated. The photoelectric property of the sample were measured and compared with silicon solar cell. The result indicated the saturated photocurrent of n-ZnO/p-Si heterojunction was 20% greater than one of the Si solar cell. It means the ZnO/Si heterojunction has a higher ability of produce photoelectron then one of silicon solarcell. The result of the photovoltaic test of n-ZnO/p-Si heterojunction show The open circuit voltage and short-circuit current of the n-ZnO/p-Si heterojunction was 400mV and 5.5mA/cm2 respectively. It was much smaller than the one of silicon solar cells. The reason was discussed

Sign in / Sign up

Export Citation Format

Share Document