scholarly journals A Dynamic Rotor Vertical-Axis Wind Turbine with a Blade Transitioning Capability

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1446 ◽  
Author(s):  
Elie Antar ◽  
Amne El Cheikh ◽  
Michel Elkhoury
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Optimized Design ◽  
Detached Eddy Simulation ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This work presents an optimized design of a dynamic rotor vertical-axis wind turbine (DR VAWT) which maximizes the operational tip-speed ratio (TSR) range and the average power coefficient (Cp) value while maintaining a low cut-in wind velocity. The DR VAWT is capable of mimicking a Savonius rotor during the start-up phase and transitioning into a Darrieus one with increasing rotor radius at higher TSRs. The design exploits the fact that with increasing rotor radius, the TSR value increases, where the peak power coefficient is attained. A 2.5D improved delayed detached eddy simulation (IDDES) approach was adopted in order to optimize the dynamic rotor design, where results showed that the generated blades’ trajectories can be readily replicated by simple mechanisms in reality. A thorough sensitivity analysis was conducted on the generated optimized blades’ trajectories, where results showed that they were insensitive to values of the Reynolds number. The performance of the DR VAWT turbine with its blades following different trajectories was contrasted with the optimized turbine, where the influence of the blade pitch angle was highlighted. Moreover, a cross comparison between the performance of the proposed design and that of the hybrid Savonius–Darrieus one found in the literature was carefully made. Finally, the effect of airfoil thickness on the performance of the optimized DR VAWT was thoroughly analyzed.

scholarly journals Assessment of stress-blended eddy simulation model for accurate performance prediction of vertical axis wind turbine

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Taurista Perdana Syawitri ◽  
Yufeng Yao ◽  
Jun Yao ◽  
Budi Chandra
Keyword(s):  
Wind Turbine ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Turbulence Models ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Content Type ◽  
Eddy Simulation

Purpose The aim of this paper is to assess the ability of a stress-blended eddy simulation (SBES) turbulence model to predict the performance of a three-straight-bladed vertical axis wind turbine (VAWT). The grid sensitivity study is conducted to evaluate the simulation accuracy. Design/methodology/approach The unsteady Reynolds-averaged Navier–Stokes equations are solved using the computational fluid dynamics (CFD) technique. Two types of grid topology around the blades, namely, O-grid (OG) and C-grid (CG) types, are considered for grid sensitivity studies. Findings With regard to the power coefficient (Cp), simulation results have shown significant improvements of predictions using compared to other turbulence models such as the k-e model. The Cp distributions predicted by applying the CG mesh are in good agreement with the experimental data than that by the OG mesh. Research limitations/implications The current study provides some new insights of the use of SBES turbulence model in VAWT CFD simulations. Practical implications The SBES turbulence model can significantly improve the numerical accuracy on predicting the VAWT performance at a lower tip speed ratio (TSR), which other turbulence models cannot achieve. Furthermore, it has less computational demand for the finer grid resolution used in the RANS-Large Eddy Simulation (LES) “transition” zone compared to other hybrid RANS-LES models. Originality/value To authors’ knowledge, this is the first attempt to apply SBES turbulence model to predict VAWT performance resulting for accurate CFD results. The better prediction can increase the credibility of computational evaluation of a new or an improved configuration of VAWT.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals PENGARUH JUMLAH BLADE DAN VARIASI PANJANG CHORD TERHADAP PERFORMANSI TURBIN ANGIN SUMBU HORIZONTAL (TASH)

2014 ◽  
Vol 4 (2) ◽  
Author(s):  
I Kade Wiratama ◽  
Made Mara ◽  
L. Edsona Furqan Prina
Keyword(s):  
Wind Turbine ◽  
Energy Use ◽  
Electrical Energy ◽  
Vertical Axis ◽  
Energy System ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine

The willingness of electrical energy is one energy system has a very important role in the economic development of a country's survival. As one energy source (wind) can be converted into electrical energy with the use of a horizontal axis wind turbine. Wind Energy Conversion Systems (WECS) that we know are two wind turbines in general, ie the horizontal axis wind turbine and vertical axis wind turbine is one type of renewable energy use wind as an energy generator. The purpose of this study was to determine the effect of the number of blade and the radius chord of rotation (n), Torque (T), Turbine Power (P), Power Coefficient (CP) and Tip Speed Ratio (λ) generated by the horizontal axis wind turbine with form linear taper. The results show that by at the maximum radius of the chord R3 the number blade 4 is at rotation = 302.700 rpm, Pturbine = 7.765 watt, Torque = 0.245 Nm, λ = 3.168 and Cp = 0.403 or 40.3%.

Performance Improvements for a Vertical Axis Wind Turbine by Means of Gurney Flap

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Yan Yan ◽  
Eldad Avital ◽  
John Williams ◽  
Jiahuan Cui
Keyword(s):  
Wind Turbine ◽  
Stokes Equations ◽  
Numerical Study ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Performance Improvements ◽  
Gurney Flap

Abstract A numerical study was carried out to investigate the effects of a Gurney flap (GF) on the aerodynamics performance of the NACA 00 aerofoil and an associated three-blade rotor of a H-type Darrieus wind turbine. The flow fields around a single aerofoil and the vertical axis wind turbine (VAWT) rotor are studied using unsteady Reynolds-averaged Navier–Stokes equations (URANS). The height of GF ranges from 1% to 5% of the aerofoil chord length. The results show that the GF can increase the lift and lift-to-drag ratio of the aerofoil as associated with the generation of additional vortices near the aerofoil trailing edge. As a result, adding a GF can significantly improve the power coefficient of the VAWT at low tip speed ratio (TSR), where it typically gives low power production. The causing mechanism is discussed in detail, pointing to flow separation and dynamic stall delay.

scholarly journals Aeroacoustic noise prediction of a vertical axis wind turbine using large eddy simulation

2021 ◽  
pp. 1475472X2110551
Author(s):  
Aya Aihara ◽  
Karl Bolin ◽  
Anders Goude ◽  
Hans Bernhoff
Keyword(s):  
Large Eddy Simulation ◽  
Wind Turbine ◽  
Sound Pressure ◽  
Vertical Axis ◽  
Low Noise ◽  
Speed Ratio ◽  
Acoustic Analogy ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Large Eddy

This study investigates the numerical prediction for the aerodynamic noise of the vertical axis wind turbine using large eddy simulation and the acoustic analogy. Low noise designs are required especially in residential areas, and sound level generated by the wind turbine is therefore important to estimate. In this paper, the incompressible flow field around the 12 kW straight-bladed vertical axis wind turbine with the rotor diameter of 6.5 m is solved, and the sound propagation is calculated based on the Ffowcs Williams and Hawkings acoustic analogy. The sound pressure for the turbine operating at high tip speed ratio is predicted, and it is validated by comparing with measurement. The measured spectra of the sound pressure observed at several azimuth angles show the broadband characteristics, and the prediction is able to reproduce the shape of these spectra. While previous works studying small-scaled vertical axis wind turbines found that the thickness noise is the dominant sound source, the loading noise can be considered to be a main contribution to the total sound for this turbine. The simulation also indicates that the received noise level is higher when the blade moves in the downwind than in the upwind side.

scholarly journals Studi simulasi penggunaan airfoil naca 6412 sebagai sudu pada turbin angin crossflow melalui pemodelan CFD 2 dimensi

2018 ◽  
Vol 13 (1) ◽  
pp. 28
Author(s):  
Muhammad Ivan Fadhil Hendrawan ◽  
Dominicus Danardono ◽  
Syamsul Hadi
Keyword(s):  
Wind Turbine ◽  
Constant Velocity ◽  
Cross Flow ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Blade Number

AbstractThe simulation aimed to understand the effect of the angle of blade number and blade number of vertical axis wind turbine with cross flow runner to enhance the performance of wind turbine. The turbine had 20, 22, and 24 number of blades. Simulation was done in 2D analysis using ANSYS-Fluent. Tip speed ratio was varied in range of 0,1-0,5 with constant velocity inlet 2 m/s. The effect of blade numbers to torque and power coefficient were analyzed and compared. It had been found that the best power coefficient were 0,5 at tip speed ratio 0,3.

Sign in / Sign up

Export Citation Format

Share Document