scholarly journals A Novel Optimal Charging Algorithm for Lithium-Ion Batteries Based on Model Predictive Control

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2238
Author(s):  
Guan-Jhu Chen ◽  
Yi-Hua Liu ◽  
Yu-Shan Cheng ◽  
Hung-Yu Pai
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Digital Signal Processor ◽  
Computational Cost ◽  
Lithium Ion ◽  
Constant Current ◽  
Li Ion Batteries ◽  
Large Power ◽  
Charging Time ◽  
Li Ion

Lithium-ion (Li-ion) batteries play a substantial role in portable consumer electronics, electric vehicles and large power energy storage systems. For Li-ion batteries, developing an optimal charging algorithm that simultaneously takes rises in charging time and charging temperature into account is essential. In this paper, a model predictive control-based charging algorithm is proposed. This study uses the Thevenin equivalent circuit battery and transforms it into the state-space equation to develop the model predictive controller. The usage of such models in the battery optimal control context has an edge due to its low computational cost, enabling the realization of the proposed technique using a low-cost Digital Signal Processor (DSP). Compared with the widely employed constant current-constant voltage charging method, the proposed charging technique can improve the charging time and the average temperature by 3.25% and 0.76%, respectively.

scholarly journals Mathematical Heat Transfer Modeling and Experimental Validation of Lithium-Ion Battery Considering: Tab and Surface Temperature, Separator, Electrolyte Resistance, Anode-Cathode Irreversible and Reversible Heat

Batteries ◽  
2020 ◽  
Vol 6 (4) ◽  
pp. 61 ◽  
Author(s):  
Anosh Mevawalla ◽  
Satyam Panchal ◽  
Manh-Kien Tran ◽  
Michael Fowler ◽  
Roydon Fraser
Keyword(s):  
Lithium Concentration ◽  
Laboratory Data ◽  
Lithium Ion ◽  
Thermal Design ◽  
Constant Current ◽  
Internal Space ◽  
Li Ion Batteries ◽  
Li Ion ◽  
Simulation Results ◽  
Electrolyte Resistance

The temperature and heat produced by lithium-ion (Li-ion) batteries in electric and hybrid vehicles is an important field of investigation as it determines the power, performance, and cycle life of the battery pack. This paper presented both laboratory data and simulation results at C-rates of 1C, 2C, 3C, and 4C at an ambient temperature of approximately 23 °C. During experiment thermocouples were placed on the surface of the battery. The thermal model assumed constant current discharge and was experimentally validated. It was observed that temperature increased with C-rates at both the surface and the tabs. We note that at 4C the battery temperature increased from 22 °C to 47.40 °C and the tab temperature increased from 22 °C to 52.94 °C. Overall, the simulation results showed that more heat was produced in the cathode than the anode, the primary source of heat was the electrolyte resistance, and the battery temperature was the highest near the tabs and in the internal space of the battery. Simulation of the lithium concentration within the battery showed that the lithium concentration was more uniform in the anode than in the cathode. These results can help the accurate thermal design and thermal management of Li-ion batteries.

A Computational Framework for Lithium Ion Cell-Level Model Predictive Control Using a Physics-Based Reduced-Order Model

2021 ◽  
Vol 5 (4) ◽  
pp. 1387-1392
Author(s):  
Marcelo A. Xavier ◽  
Aloisio K. de Souza ◽  
Kiana Karami ◽  
Gregory L. Plett ◽  
M. Scott Trimboli
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Lithium Ion ◽  
Reduced Order Model ◽  
Order Model ◽  
Cell Level ◽  
Computational Framework ◽  
Reduced Order ◽  
Lithium Ion Cell ◽  
Level Model

Overcharge protection of lithium-ion batteries with phenothiazine redox shuttles

2021 ◽  
Author(s):  
Susan A. Odom
Keyword(s):  
Lithium Ion Batteries ◽  
Lithium Ion ◽  
Li Ion Batteries ◽  
Phenothiazine Derivatives ◽  
Redox Shuttles ◽  
Li Ion ◽  
Overcharge Protection

Overcharge protection of Li-ion batteries with a variety of phenothiazine derivatives.

scholarly journals Parameter optimization and yield prediction of cathode coating separation process for direct recycling of end-of-life lithium-ion batteries

RSC Advances ◽  
2021 ◽  
Vol 11 (39) ◽  
pp. 24132-24136
Author(s):  
Liurui Li ◽  
Tairan Yang ◽  
Zheng Li
Keyword(s):  
Lithium Ion Batteries ◽  
End Of Life ◽  
Lithium Ion ◽  
Separation Process ◽  
Yield Prediction ◽  
Li Ion Batteries ◽  
Treatment Efficiency ◽  
Control Factors ◽  
Li Ion ◽  
Pre Treatment

The pre-treatment efficiency of the direct recycling strategy in recovering end-of-life Li-ion batteries is predicted with levels of control factors.

scholarly journals The Necessity of Recycling of Waste Li-Ion Batteries Used in Electric Vehicles as Objects Posing a Threat to Human Health and the Environment

Recycling ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 35
Author(s):  
Agnieszka Sobianowska-Turek ◽  
Weronika Urbańska ◽  
Anna Janicka ◽  
Maciej Zawiślak ◽  
Jędrzej Matla
Keyword(s):  
Automotive Industry ◽  
Morphological Characteristics ◽  
Lithium Ion ◽  
Li Ion Batteries ◽  
Customer Expectations ◽  
Lithium Ion Cells ◽  
Improper Use ◽  
Complex Chemical Composition ◽  
Li Ion ◽  
Legal Restrictions

The automotive industry is one of the fastest-growing sectors of the modern economy. Growing customer expectations, implementing solutions related to electromobility, and increasingly stringent legal restrictions in the field of environmental protection, determine the development and introduction of innovative technologies in the field of car production. To power the most modern vehicles that include electric and hybrid cars, packages of various types of lithium-ion cells are used, the number of which is constantly growing. After use, these batteries, due to their complex chemical composition, constitute hazardous waste that is difficult to manage and must be recycled in modern technological lines. The article presents the morphological characteristics of the currently used types of Li-ion cells, and the threats to the safety of people and the environment that may occur in the event of improper use of Li-ion batteries and accumulators have been identified and described on the basis of the Regulation of the European Parliament and Council (EC) No. 1272/2008 of 16 December 2008 and No. 1907/2006 of 18 December 2006 on the classification, labeling and packaging of substances and mixtures and the registration, evaluation, authorization and restriction of chemicals (REACH), establishing the European Chemicals Agency.

Metal–organic nanofibers as anodes for lithium-ion batteries

RSC Advances ◽  
2015 ◽  
Vol 5 (26) ◽  
pp. 20386-20389 ◽  
Author(s):  
Chongchong Zhao ◽  
Cai Shen ◽  
Weiqiang Han
Keyword(s):  
Amino Acid ◽  
Lithium Ion Batteries ◽  
Anode Materials ◽  
Lithium Ion ◽  
Copper Nitrate ◽  
Li Ion Batteries ◽  
Metal Organic ◽  
Li Ion

Metal organic nanofibers (MONFs) synthesized from precursors of amino acid and copper nitrate were applied as anode materials for Li-ion batteries.

Synthesis and Electrochemical Properties of Spherical LiFePO4/C Composite via Spray Drying

2015 ◽  
Vol 1120-1121 ◽  
pp. 554-558 ◽  
Author(s):  
Juan Mei Wang ◽  
Bing Ren ◽  
Ying Lin Yan ◽  
Qing Zhang ◽  
Yan Wang
Keyword(s):  
Diffusion Coefficient ◽  
Electrochemical Properties ◽  
Spray Drying ◽  
Electrochemical Impedance ◽  
Retention Rate ◽  
Lithium Ion ◽  
Constant Current ◽  
Ion Diffusion ◽  
Electrochemical Tests ◽  
Li Ion

In this work, spherical LiFePO4/C composite had been synthesized by co-precipitation and spray drying method. The structure, morphology and electrochemical properties of the samples were characterized by X-ray diffraction (XRD), scanning electron micrograph (SEM), transmission electron microscope (TEM), constant current charge-discharge tests and electrochemical impedance spectroscopy (EIS) tests. The spherical LiFePO4/C particles consisted of a number of smaller grains. The results showed that the morphology of LiFePO4/C particles seriously affected the Li-ion diffusion coefficient and electrochemical properties of lithium ion batteries. Electrochemical tests revealed the spherical LiFePO4/C composite had excellent Li-ion diffusion coefficient which was calculated to be 1.065×10-11 cm2/s and discharge capacity of 149 (0.1 C), 139 (0.2 C), 133 (0.5 C), 129 (1 C) and 124 mAhg-1(2 C). After 50 cycles, the capacity retention rate was still 93.5%.

Probing the Effect of High Energy Ball Milling on the Structure and Properties of LiNi1/3Mn1/3Co1/3O2 Cathodes for Li-Ion Batteries

2016 ◽  
Vol 13 (3) ◽  
Author(s):  
Malcolm Stein ◽  
Chien-Fan Chen ◽  
Matthew Mullings ◽  
David Jaime ◽  
Audrey Zaleski ◽  
...  
Keyword(s):  
Particle Size ◽  
Electrochemical Performance ◽  
Crystallite Size ◽  
Ball Milling ◽  
Lithium Ion ◽  
High Energy ◽  
Li Ion Batteries ◽  
Structure And Properties ◽  
Transfer Resistance ◽  
Li Ion

Particle size plays an important role in the electrochemical performance of cathodes for lithium-ion (Li-ion) batteries. High energy planetary ball milling of LiNi1/3Mn1/3Co1/3O2 (NMC) cathode materials was investigated as a route to reduce the particle size and improve the electrochemical performance. The effect of ball milling times, milling speeds, and composition on the structure and properties of NMC cathodes was determined. X-ray diffraction analysis showed that ball milling decreased primary particle (crystallite) size by up to 29%, and the crystallite size was correlated with the milling time and milling speed. Using relatively mild milling conditions that provided an intermediate crystallite size, cathodes with higher capacities, improved rate capabilities, and improved capacity retention were obtained within 14 μm-thick electrode configurations. High milling speeds and long milling times not only resulted in smaller crystallite sizes but also lowered electrochemical performance. Beyond reduction in crystallite size, ball milling was found to increase the interfacial charge transfer resistance, lower the electrical conductivity, and produce aggregates that influenced performance. Computations support that electrolyte diffusivity within the cathode and film thickness play a significant role in the electrode performance. This study shows that cathodes with improved performance are obtained through use of mild ball milling conditions and appropriately designed electrodes that optimize the multiple transport phenomena involved in electrochemical charge storage materials.

Sign in / Sign up

Export Citation Format

Share Document