scholarly journals Numerical Study on the Performance and NOx Emission Characteristics of an 800cc MPI Turbocharged SI Engine

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 7419
Author(s):  
Seungmin Kim ◽  
Jaesam Shim ◽  
Youngsoo Cho ◽  
Back-Sub Sung ◽  
Jungsoo Park
Keyword(s):  
Engine Performance ◽  
Boost Pressure ◽  
Exhaust Gas ◽  
Intake Valve ◽  
Si Engine ◽  
Spark Timing ◽  
Performance And Emissions ◽  
Valve Overlap ◽  
Engine Performance And Emissions ◽  
Exhaust Gas Emissions

The main purpose of this study is to optimize engine performance and emission characteristics of off-road engines with retarded spark timing compared to MBT by repurposing the existing passenger engine. This study uses a one-dimensional (1D)-simulation to develop a non-road gasoline MPI turbo engine. The SI turbulent flame model of the GT-suite, an operational performance predictable program, presents turbocharger matching and optimal operation design points. To optimize the engine performance, the SI turbulent model uses three operation parameters: spark timing, intake valve overlap, and boost pressure. Spark timing determines the initial state of combustion and thermal efficiency, and is the main variable of the engine. The maximum brake torque (MBT) point can be identified for spark timing, and abnormal combustion phenomena, such as knocking, can be identified. Spark timing is related to engine performance, and emissions of exhaust pollutants are predictable. If the spark timing is set to variables, the engine performance and emissions can be confirmed and predicted. The intake valve overlap can predict the performance and exhaust gas by controlling the airflow and combustion chamber flow, and can control the performance of the engine by controlling the flow in the cylinder. In addition, a criterion can be set to consider the optimum operating point of the non-road vehicle while investigating the performance and exhaust gas emissions accompanying changes in boost pressure With these parameters, the design of experiment (DoE) of the 1D-simulation is performed, and the driving performance and knocking phenomenon for each RPM are predicted during the wide open throttle (WOT) of the gasoline MPI Turbo SI engine. The multi-objective Pareto technique is also used to optimize engine performance and exhaust gas emissions, and to present optimized design points for the target engine, the downsized gasoline MPI Turbo SI engine. The results of the Pareto optimal solution showed a maximum torque increase of 12.78% and a NOx decrease of 54.31%.

scholarly journals Experimental Comparative Study on Performance and Emissions of E85 Adopting Different Injection Approaches in a Turbocharged PFI SI Engine

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1555 ◽  
Author(s):  
Cinzia Tornatore ◽  
Luca Marchitto ◽  
Maria Antonietta Costagliola ◽  
Gerardo Valentino
Keyword(s):  
Fuel Injection ◽  
Reference Conditions ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Intake Manifold ◽  
Si Engine ◽  
Spark Timing ◽  
Performance And Emissions ◽  
Ethanol Blends ◽  
Cylinder Port

This study examines the effects of ethanol and gasoline injection mode on the combustion performance and exhaust emissions of a twin cylinder port fuel injection (PFI) spark ignition (SI) engine. Generally, when using gasoline–ethanol blends, alcohol and gasoline are externally mixed with a specified blending ratio. In this activity, ethanol and gasoline were supplied into the intake manifold into two different ways: through two separated low pressure fuel injection systems (Dual-Fuel, DF) and in a blend (mix). The ratio between ethanol and gasoline was fixed at 0.85 by volume (E85). The initial reference conditions were set running the engine with full gasoline at the knock limited spark advance boundary, according to the standard engine calibration. Then E85 was injected and a spark timing sweep was carried out at rich, stoichiometric, and lean conditions. Engine performance and gaseous and particle exhaust emissions were measured. Adding ethanol could remove over-fueling with an increase in thermal efficiency without engine load penalties. Both ethanol and charge leaning resulted in a lowering of CO, HC, and PN emissions. DF injection promoted a faster evaporation of gasoline than in blend, shortening the combustion duration with a slight increase in THC and PN emissions compared to the mix mode.

Investigation of Engine Performance and Emission Characteristics of Si Engine Fuelled with Ethanol Blends by Numerical Simulation

2014 ◽  
Vol 1016 ◽  
pp. 597-601
Author(s):  
Ceyla Ozgur ◽  
Erdi Tosun ◽  
Tayfun Ozgur ◽  
Gökhan Tuccar ◽  
Kadi̇r Aydin
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition Engine ◽  
Emission Characteristics ◽  
Si Engine ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Ethanol Addition ◽  
Ethanol Blends ◽  
Engine Performance And Emissions

In this study the influences of ethanol addition to gasoline on an spark ignition engine performance and emissions were explored. AVL BOOST software was used to simulate the performance and emission characteristics of different ethanol-gasoline blends. The blended fuels contain 5%, 10% and 15% of ethanol by volume, and indicated as B95E5, B90E10, and B85E15, respectively. The results showed that ethanol addition to gasoline fuel improve combustion process, decrease CO emissions and reduce BSFC of the SI engine.

Sign in / Sign up

Export Citation Format

Share Document