scholarly journals Application of Composite Materials in an Upgraded Engine Low-Pressure Compressor for a Regional Passenger Aircraft

Inventions ◽  
2021 ◽  
Vol 6 (3) ◽  
pp. 54
Author(s):  
Yury Ravikovich ◽  
Alexander Arkhipov ◽  
Alexander Shakhov ◽  
Timur Erofeev
Keyword(s):  
Composite Materials ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Dynamic Strength ◽  
Low Pressure ◽  
Final Decision ◽  
Structural Elements ◽  
Safety Margins ◽  
Three Dimensional Finite Element ◽  
Pressure Compressor

Computational and experimental studies have been carried out to evaluate the robustness and durability of components produced of polymer composite materials (PCM), as a part of the modernization of the low-pressure compressor (LPC) of the engine for the regional aircraft. For a preliminary assessment of the static and dynamic strength of the parts, a series of three-dimensional finite element calculations and tests of laboratory specimens, structural elements cut from finished parts, have been performed. Testing the laboratory samples made it possible to compare the obtained mechanical properties with the properties declared by PCM suppliers and to conduct a mor e correct assessment of the safety margins of the parts. To decide whether to install parts on the engine, fatigue and erosion tests of the structural elements cut from the finished parts were carried out. The final decision on the performance of the PCM parts was made after testing them as part of the upgraded LPC on the engine. The criterion for evaluating the erosion resistance of PCM parts has been introduced, which makes it possible to assess their performance during operation.

Numerical Modeling of Tube Hydropiercing Using Phenomenological and Micro-Mechanical Damage Criteria

2013 ◽  
Vol 549 ◽  
pp. 172-179 ◽  
Author(s):  
Amir Hassannejadasl ◽  
Daniel E. Green
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Equivalent Plastic Strain ◽  
Mechanical Damage ◽  
High Strength ◽  
Dimensional Finite Element ◽  
Steel Dp600 ◽  
Three Dimensional Finite Element ◽  
Jc Model ◽  
Damage Criteria

Hydropiercing is an efficient way of piercing holes in mass produced hydroformed parts with complex geometries. By driving piercing punches radially into a hydroformed and fully pressurized tube, holes will be pierced and extruded into the tube-wall. Recent experimental studies have shown that the formability of advanced high strength steel (AHSS) tubes can be increased with the application of internal pressure. In this study, three-dimensional finite element simulations of a tube hydropiercing process of a dual phase steel (DP600) were performed in LS-DYNA, using phenomenological, micromechanical and combined damage criteria. Damage was included in the numerical analysis by applying constant equivalent plastic strain (CEPS), the Gurson-Tvergaard-Needleman (GTN), and the Extended GTN (GTN+JC) model. In order to calibrate the parameters in each model, a specialized hole-piercing fixture was designed and piercing tests were carried out on non-pressurized tube specimens. Of the various ductile fracture criteria, the results predicted with the GTN+JC model, such as the punch load-displacement, the roll-over depth, and the quality of the clearance zone correlated the best with the experimental data.

scholarly journals Condensation method in practical modal analysis of hull vibration with application of 3D FE model

2019 ◽  
pp. 162-169
Author(s):  
Valeriy Sutyrin
Keyword(s):  
Modal Analysis ◽  
Three Dimensional ◽  
Element Model ◽  
Fe Model ◽  
Structural Elements ◽  
Natural Vibrations ◽  
Condensation Method ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Analytical Approaches

This paper gives modal analysis results for mid-body of a refrigerator carrier ship by means of combined three-dimensional finite-element model with 1.5 million DOF. The study estimates the error of modal analysis for the ship structure if its boundary conditions are specified in advance, i.e. approximately, as well as analyses the gain in time offered by structuring the analytical model as per reduction (condensation) method. Analytical approaches thus transformed can be successfully applied in filtering lower frequencies and modes of natural vibrations for structural elements and joints of hull in the direct vicinity of exciting force application points.

A Biomechanical Model of Lumbar Spine

2000 ◽  
Author(s):  
Subramanya Uppala ◽  
Robert X. Gao ◽  
Scott Cowan ◽  
K. Francis Lee
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Fe Model ◽  
Flexion Extension ◽  
Cortical Shell ◽  
Three Dimensional Finite Element

Abstract The strength and stability of the lumbar spine are determined not only by the bone and muscles, but also by the visco-elastic structures and the interplay between the different components of the spine, such as ligaments, capsules, annulus fibrosis, and articular cartilage. In this paper we present a non-linear three-dimensional Finite Element model of the lumbar spine. Specifically, a three-dimensional FE model of the L4-5 one-motion segment/2 vertebrae was developed. The cortical shell and the cancellous bone of the vertebral body were modeled as 3D isoparametric eight-nodal elements. Finite element models of spinal injuries with fixation devices are also developed. The deformations across the different sections of the spine are observed under the application of axial compression, flexion/extension, and lateral bending. The developed FE models provided input to both the fixture design and experimental studies.

Analysis of Repaired Cracks With Bonded Composite Wrap in Pipes Under Bending

2016 ◽  
Vol 138 (6) ◽  
Author(s):  
Aida Achour ◽  
Abdulmohsen Albedah ◽  
Faycal Benyahia ◽  
Bel Abbes Bachir Bouiadjra ◽  
Djamel Ouinas
Keyword(s):  
Composite Materials ◽  
Fracture Criterion ◽  
Three Dimensional ◽  
Bending Moment ◽  
Element Analysis ◽  
Geometrical Properties ◽  
Bonded Composite ◽  
Dimensional Finite Element ◽  
Offshore Risers ◽  
Three Dimensional Finite Element

Composite materials have been used to structurally repair piping and other facilities for many years. However, the original use of composite materials was for repairing corroded pipelines where the intent was to restore strength to the damaged section of the pipeline. In addition to repairing corrosion, composite materials have successfully been used to repair dents, wrinkle bends, induction bends, and pipe fittings including elbows and tees as well as repair of offshore risers. In this study, the behavior of circumferential through cracks in repaired pipe with bonded composite wrap subjected to bending moment is investigated using three-dimensional finite-element analysis. The stress intensity factor (SIF) is utilized as a fracture criterion. The effects of the mechanical and geometrical properties of the adhesive on the variation of the SIF at the crack front were also analyzed. The obtained results show that the presence of the bonded composite repair significantly reduces the SIF, which can improve the residual lifespan of the pipe. Meanwhile, the SIF is also reduced as the elastic and the geometrical wrap properties are improved, particularly when the Young's modulus of the adhesive and the wrap thickness are increased.

Experimental Study and Finite Element Analysis on RPC Footwalk Braces

2006 ◽  
Vol 302-303 ◽  
pp. 713-719
Author(s):  
Zhi Gang Yan ◽  
Gui Ping Yan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Performance ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Safety Margin ◽  
Experimental Results ◽  
Element Analysis ◽  
Three Dimensional Finite Element ◽  
Reactive Powder

In this paper, a series of Reactive powder concrete (RPC) footwalk braces without conventional steel bars are designed for the Qing-Zang railway. Experimental studies on the braces are conducted in order to test the mechanical character of the braces. Totally eight RPC footwalk braces are experimentally measured with static load. According to the analysis of the experimental results, the ratio of the crack load got from the experiment to the design load is 2.54 and the deflection ductile coefficient is 2.32. The experimental results show that the mechanical performance of RPC footwalk braces can satisfy the engineering requirements and there is enough safety margin for footwalk braces. A three-dimensional finite element analysis (FEA) is also carried out and the results of FEA are compared with that of the experiments. The results show that the FEA method can be used in designing the RPC footwalk braces.

Numerical Simulations of Full-Scale Corroded Pipe Tests With Combined Loading

1997 ◽  
Vol 119 (4) ◽  
pp. 457-466 ◽  
Author(s):  
S. Roy ◽  
S. Grigory ◽  
M. Smith ◽  
M. F. Kanninen ◽  
M. Anderson
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Full Scale ◽  
Combined Loading ◽  
Pipe Failure ◽  
Element Analysis ◽  
Line Pipe ◽  
Safety Margins ◽  
Failure Predictions ◽  
Three Dimensional Finite Element

The ANSI/ASME B31G guideline has been useful to pipeline operators in assessing the integrity of corroded line pipe. Because large safety margins have had to be incorporated, the guidelines can be excessively conservative, which in turn can force costly repairs and replacements that may not actually be necessary. On the other hand, because the current guidelines consider only pressure loading and neglect bending and axial compression, they could give nonconservative failure predictions when combined loading exists. Therefore, a study was initiated to develop a theoretically sound methodology for assessing the integrity of corroded line pipe subjected to combined loading. A key step in the successful application of this methodology is the development of a sophisticated three-dimensional finite element procedure that can accurately simulate full-scale pipe tests under conditions of combined loading. This paper describes thirteen full-scale failure tests on artificially corroded pipes subjected to simultaneous internal pressure, bending, and longitudinal compression and presents a detailed account of the finite element analysis procedure that was developed to simulate these tests numerically. Additional finite element analyses that were conducted to investigate the effect of key parameters on failure, and to expand the corroded pipe failure database, are also discussed.

Sign in / Sign up

Export Citation Format

Share Document