scholarly journals Lubricated Loaded Tooth Contact Analysis and Non-Newtonian Thermoelastohydrodynamics of High-Performance Spur Gear Transmission Systems

Lubricants ◽  
2020 ◽  
Vol 8 (2) ◽  
pp. 20 ◽  
Author(s):  
Gajarajan Sivayogan ◽  
Ramin Rahmani ◽  
Homer Rahnejat
Keyword(s):  
High Speed ◽  
High Performance ◽  
Spur Gear ◽  
Contact Analysis ◽  
Operating Conditions ◽  
Tooth Contact Analysis ◽  
Transmission Systems ◽  
Tooth Contact ◽  
Contact Kinematics ◽  
Loaded Tooth Contact Analysis

Energy efficiency and functional reliability are the two key requirements in the design of high-performance transmissions. Therefore, a representative analysis replicating real operating conditions is essential. This paper presents the thermoelastohydrodynamic lubrication (TEHL) of meshing spur gear teeth of high-performance racing transmission systems, where high generated contact pressures and lubricant shear lead to non-Newtonian traction. The determination of the input contact geometry of meshing pairs as well as contact kinematics are essential steps for representative TEHL. These are incorporated in the current analysis through the use of Lubricated Loaded Tooth Contact Analysis (LLTCA), which is far more realistic than the traditional Tooth Contact Analysis (TCA). In addition, the effects of lubricant and flash surface temperature rise of contacting pairs, leading to the thermal thinning of lubricant, are taken into account using a thermal network model. Furthermore, high-speed contact kinematics lead to shear thinning of the lubricant and reduce the film thickness under non-Newtonian traction. This comprehensive approach based on established TEHL analysis, particularly including the effect of LLTCA on the TEHL of spur gears, has not hitherto been reported in literature.

scholarly journals Lubricated loaded tooth contact analysis for spur gear pair

2019 ◽  
Vol 8 (1) ◽  
pp. 23
Author(s):  
Callum Oglieve ◽  
Gajarajan Sivayogan ◽  
Homer Rahnejat ◽  
Mahdi Mohammadpour
Keyword(s):  
Spur Gear ◽  
Contact Analysis ◽  
Gear Pair ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Loaded Tooth Contact Analysis

scholarly journals Lubricated loaded tooth contact analysis for spur gear pair

2019 ◽  
Vol 8 (1) ◽  
pp. 23 ◽  
Author(s):  
Callum Oglieve ◽  
Gajarajan Sivayogan ◽  
Mahdi Mohammadpour ◽  
Homer Rahnejat
Keyword(s):  
Spur Gear ◽  
Contact Analysis ◽  
Gear Pair ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Loaded Tooth Contact Analysis

Data-driven process control for manufacturing spiral bevel and hypoid gears by using design for six sigma (DFSS) considering numerical loaded tooth contact analysis (NLTCA)

2021 ◽  
pp. 095440542110236
Author(s):  
Kaibin Rong ◽  
Han Ding ◽  
Biyun Song ◽  
Jinhao Gao ◽  
Jinyuan Tang
Keyword(s):  
Process Control ◽  
High Performance ◽  
Contact Analysis ◽  
Data Driven ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Manufacturing Process Control ◽  
Spiral Bevel ◽  
Loaded Tooth Contact Analysis

Data-driven process control considering both geometric and loaded contact performance evaluations has been an increasingly important stage in field of spiral bevel and hypoid gears. A new data-driven manufacturing process control strategy is proposed for a high performance spiral bevel and hypoid gears. Here, to distinguish with the conventional simulated loaded tooth contact analysis (SLTCA) using economical finite element software package, the numerical loaded tooth contact analysis (NLTCA) is of more flexibility and practicality. In light of the advantages of the improved design for six sigma (DFSS), it is integrated with NLTCA for establishing a novel data-driven process control of gear manufacturing. Firstly, in improved DFSS framework, quality function deployment (QFD) is used to determine four sub-objective high-performance evaluation items. Then, their data-driven relationships between machine settings are respectively determined by using NLTCA. In particular, the manufacturing process control is further converted into multi-objective optimization (MOO) modification of the hypoid generator settings. Finally, an interactive preference point approach is applied for data-driven control of its iterative step and it can obtain a robust solution from Pareto optimal front. A case study is provided to verify the proposed methodology.

Simulation and Experimental Measurement of the Transmission Error of Real Hypoid Gears Under Load

2000 ◽  
Vol 122 (1) ◽  
pp. 109-122 ◽  
Author(s):  
Claude Gosselin ◽  
Thierry Guertin ◽  
Didier Remond ◽  
Yves Jean
Keyword(s):  
Measurement Data ◽  
Simulation Models ◽  
Transmission Error ◽  
Contact Analysis ◽  
Hypoid Gear ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Hypoid Gears ◽  
Loaded Tooth Contact Analysis ◽  
Analysis Models

The Transmission Error and Bearing Pattern of a gear set are fundamental aspects of its meshing behavior. To assess the validity of gear simulation models, the Transmission Error and Bearing Pattern of a Formate Hypoid gear set are measured under a variety of operating positions and applied loads. Measurement data are compared to simulation results of Tooth Contact Analysis and Loaded Tooth Contact Analysis models, and show excellent agreement for the considered test gear set. [S1050-0472(00)00901-6]

Loaded Tooth Contact Analysis of Power-Split Gear Drives Considering Shaft Deformation and Assembly Errors

2015 ◽  
Author(s):  
Siang-Yu Ye ◽  
Shyi-Jeng Tsai
Keyword(s):  
Power Transmission ◽  
Planetary Gear ◽  
Load Sharing ◽  
Contact Analysis ◽  
Influence Coefficient ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Power Split ◽  
Loaded Tooth Contact Analysis ◽  
Compact Design

The power-split gear mechanisms is widely applied in power transmission because of the advantages of compact design, lighter weight and high power density. The load sharing and the load distribution are the important performance issues while designing the power split mechanisms. The paper propose a computerized approach based on the influence coefficient method for loaded tooth contact analysis of such the gear transmission. Not only the load sharing of the multiple contact tooth pairs and the loaded transmission errors, but also the distributed contact stresses and the corresponding contact patterns on all the engaged tooth flanks can be calculated by using the proposed LTCA approach. Some analysis results are also discussed with a study case of the first planetary stage of a compound cycloid planetary gear drive.

Stress Analysis of Spherical Gear Sets

2009 ◽  
Author(s):  
Li-Chi Chao ◽  
Chung-Biau Tsay
Keyword(s):  
Gear Tooth ◽  
Three Dimensional ◽  
Contact Analysis ◽  
Design Parameters ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Contact Points ◽  
Tooth Surfaces ◽  
Loaded Tooth Contact Analysis ◽  
Spherical Gear

The spherical gear is a new type of gear proposed by Mitome et al. [1]. Different from that of the conventional spur or helical gear sets, the spherical gear set can allow variable shaft angles and large axial misalignments without gear interference during the gear drive meshing [1, 2]. Geometrically, the spherical gear has two types of gear tooth profiles, the concave tooth and convex tooth. In practical transmission applications, the contact situation of a spherical gear set is very complex. To obtain a more realistic simulation result, the loaded tooth contact analysis (LTCA) has been performed by employing the finite element method (FEM). According to the derived mathematical model of spherical gear tooth surfaces, an automatic meshes generation program for three-dimensional spherical gears has been developed. Beside, tooth contact analysis (TCA) of spherical gears has been performed to simulate the contact points of the spherical gear set. Furthermore, the contact stress contours of spherical gear tooth surfaces and bending stress of tooth roots have been investigated by giving the design parameters, material properties, loadings and boundary conditions of spherical gears.

Sign in / Sign up

Export Citation Format

Share Document