scholarly journals Study of Concrete under Combined Action of Aggressive Environment and Long-Term Loading

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6612
Author(s):  
Yaroslav Blikharskyy ◽  
Jacek Selejdak ◽  
Nadiia Kopiika ◽  
Rostyslav Vashkevych
Keyword(s):  
Reinforced Concrete ◽  
Concrete Strength ◽  
Aggressive Medium ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Corrosion Damage ◽  
Simultaneous Action ◽  
Reinforced Concrete Structures ◽  
Cross Sectional ◽  
Aggressive Environment

A significant part of reinforced concrete structures is subjected to intensive environmental impact during operation. This can cause local destruction and failure of buildings if obligatory measures are not taken to protect them from corrosion. This is especially true for industrial buildings, where the environment could be contaminated with aggressive products or waste. An important issue is the development of methods for calculating the load-bearing capacity and serviceability of reinforced concrete structures with corrosion damage. The main reason for this is the necessity to determine the durability and reliability of buildings and structures and the estimation of their safe operation time. As corrosion damages of concrete are a critical issue, more detailed experimental studies are needed. This paper presents experimental studies of concrete prisms under the simultaneous action of an aggressive environment and a constant level of compressive force. In total, 32 prisms under different loading conditions and in different aggressive medium were tested. Samples were divided in series, for which different load levels were chosen (0.25fck, 0.35fck, 0.45fck). Additionally, control samples in the air and immersed in water were tested. During the experiment, different parameters were monitored and recorded: decrease of cross-sectional size, the temperature and environmental humidity. Results of the study showed that destruction occurred due to the presence of corrosion damages of concrete and a reduction of the cross-sectional area. The stresses in the concrete at the destruction stage were less than the value of the prism strength by 10–12%. It was established that along the contour of the section, there is a partially degraded layer of concrete of 1.5–3.7 mm thickness, with corrosion microcracks and corrosion products. Additionally, experimental and theoretical diagrams of concrete with corrosion damages were obtained and compared. The ultimate deformations of concrete with corrosion damage, which correspond to the prismatic strength of concrete, in comparison with undamaged concrete were lower by 11–18%. Therefore, the concrete strength is decreased during exploitation under loading in an aggressive environment, which needs to be taken into account during calculations.

Improvement Of Curvilinear Diagrams Of Concrete Deformation

2019 ◽  
pp. 99-104
Keyword(s):  
Reinforced Concrete ◽  
Peak Load ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Deformation Model ◽  
Reinforced Concrete Structures ◽  
Significant Difference ◽  
Deformation Diagrams

Problems when calculating reinforced concrete structures based on the concrete deformation under compression diagram, which is presented both in Russian and foreign regulatory documents on the design of concrete and reinforced concrete structures are considered. The correctness of their compliance for all classes of concrete remains very approximate, especially a significant difference occurs when using Euronorm due to the different shape and sizes of the samples. At present, there are no methodical recommendations for determining the ultimate relative deformations of concrete under axial compression and the construction of curvilinear deformation diagrams, which leads to limited experimental data and, as a result, does not make it possible to enter more detailed ultimate strain values into domestic standards. The results of experimental studies to determine the ultimate relative deformations of concrete under compression for different classes of concrete, which allowed to make analytical dependences for the evaluation of the ultimate relative deformations and description of curvilinear deformation diagrams, are presented. The article discusses various options for using the deformation model to assess the stress-strain state of the structure, it is concluded that it is necessary to use not only the finite values of the ultimate deformations, but also their intermediate values. This requires reliable diagrams "s–e” for all classes of concrete. The difficulties of measuring deformations in concrete subjected to peak load, corresponding to the prismatic strength, as well as main cracks that appeared under conditions of long-term step loading are highlighted. Variants of more accurate measurements are proposed. Development and implementation of the new standard GOST "Concretes. Methods for determination of complete diagrams" on the basis of the developed method for obtaining complete diagrams of concrete deformation under compression for the evaluation of ultimate deformability of concrete under compression are necessary.

EXPERIMENTAL STUDIES OF REINFORCED CONCRETE STRUCTURES WITH CROSS-SHAPED SPATIAL CRACK UNDER TORSION WITH BENDING

2020 ◽  
Vol 92 (6) ◽  
pp. 13-25
Author(s):  
Vl.I. KOLCHUNOV ◽  
◽  
A.I. DEMYANOV ◽  
M.M. MIHAILOV ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Experimental Determination ◽  
Calculation Method ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Design Parameters ◽  
Reinforced Concrete Structures ◽  
Experimental Scheme

The article offers a method and program for experimental studies of reinforced concrete structures with cross-shaped spatial crack under torsion with bending, the main purpose of which is to check the design assumptions and experimental determination of the design parameters of the proposed calculation method. The conducted experimental studies provide an opportunity to test the proposed calculation apparatus and clarify the regularities for determining deflections, angles of rotation of extreme sections, and stresses in the compressed zone of concrete. For analysis, the article presents a typical experimental scheme for the formation and development of cracks in the form of a sweep, as well as characteristic graphs of the dependence of the angles of rotation of end sections.

scholarly journals Experimental study of the influence of crack width due to corrosion behaviour using different measurement methods and different exposures

2019 ◽  
Vol 289 ◽  
pp. 08005
Author(s):  
Martin Schneider ◽  
Georg Gardener
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Corrosion Behaviour ◽  
Concrete Strength ◽  
Concrete Structures ◽  
Chloride Ions ◽  
Reinforced Concrete Structures ◽  
Reinforcing Steel ◽  
Surface Corrosion ◽  
Potential Mapping

Corrosion of reinforcing steel has a great influence in reducing the lifetime of concrete structures; Carbonation of the concrete pore solution causes surface corrosion on the steel and diffusion of chloride ions through the capillary system of the concrete cover causes pitting corrosion on the steel surface. Corrosion of metals is highly dependent on the environmental conditions. Exposure to chloride ions can be critical to the service life of reinforced concrete structures. The durability of reinforced concrete structures exposed to deicing salt or marine environments can be affected by impact of chloride ions. Detection methods for the rate of corrosion of non-destructive and destructive procedures were analysed. The potential mapping applied on the concrete surface was discussed as a standard method for corrosion detection and will be explained in detail including the application boundaries of the method. It is assumed that the corrosion behaviour of reinforcing steel depends on crack widths. To analyse that, 8 coated and 8 uncoated test samples with different concrete strength classes were used. The concrete objects were exposed to a 3% sodium chloride solution. The corrosion behaviour of reinforcing steel is analysed by using potential mapping with different reference electrodes (Ag/AgCl and Cu/CuSO4). The results show a significant correlation between crack size and protection system on the surface. The maximum crack width with a low indication of corrosion was found to be 0.1 mm.

scholarly journals FLEXURAL REINFORCED CONCRETE ELEMENTS NORMAL SECTION BEARING CAPACITY EVALUATION IN FRACTURE STAGE

2017 ◽  
Vol 9 (2) ◽  
pp. 70-78 ◽  
Author(s):  
Justas SLAITAS ◽  
Zbynek HLAVAC ◽  
Arnoldas ŠNEIDERIS
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Crack Depth ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Assessment Process ◽  
Reinforced Concrete Structures ◽  
Compression Zone ◽  
Normal Section

This article examines flexural reinforced concrete structures condition assessment process in existing buildings on the stage where the reinforcement stress is between the yield and the tensile strength. The research is made on V. Jokūbaitis proposed methodology directly measuring the compression zone height, allowing us to evaluate the behavior of reinforced concrete beam fracture sufficiently precisely. This paper confirms the hypothesis that, when reinforcement reaches yielding stress, elastic strain dominates in concrete‘s compression zone and it is reasonable to use triangular concrete compression zone diagram, without tensile concrete above crack evaluation. The methodology of reinforced concrete structures bearing capacity assessment according to limit normal section crack depth is proposed. There is established connection between bending moments, when reinforcement achieve yielding stress and tensile strength, which allows us to decide about structures bearing capacity reserve. The results are confirmed with experimental studies and calculated values obtained by methodologies based on different reduced stress diagrams of concrete‘s compressive zone.

scholarly journals COMBINED EFFECT OF CARBONATION AND CHLORIDE AGGRESSION: DEG-RADATION OF REINFORCED CONCRETE STRUCTURES

2018 ◽  
Author(s):  
L.V. KIM ◽  
E.E. SHALYI ◽  
S.N. LEONOVICH ◽  
N.A. BUDREVICH
Keyword(s):  
Reinforced Concrete ◽  
Ph Value ◽  
Concrete Structures ◽  
Chloride Concentration ◽  
Protective Layer ◽  
Sharp Decrease ◽  
Threshold Concentration ◽  
Steel Reinforcement ◽  
Reinforced Concrete Structures ◽  
Cross Sectional

Corrosion reinforcement marine hydraulic structures due to chloride aggression and carbonization of concrete leads to a sharp decrease in the safety of the structure. The steel reinforcement will be subjected to a so-called depassivation process, once the chloride concentration on surface exceeds a certain threshold concentration, or the pH value in the protective layer of concrete decreases to a threshold value due to carbonation. Electrochemical reactions begin to occur with the formation of corrosion products with the penetration of oxygen on the steel reinforcement surface. This leads to cracking of the protective layer of concrete. It should also be taken into account that, due to corrosion mechanisms, the cross-sectional area of the reinforcement also decreases. The article suggests a method for predicting the complex degradation of reinforced concrete structures, taking into account various mechanisms of corrosion wear, which will allow developing effective ways to improve the durability and maintainability of structures operated in the marine environment.

Sign in / Sign up

Export Citation Format

Share Document