scholarly journals Using a Fuzzy Inference System to Obtain Technological Tables for Electrical Discharge Machining Processes

Mathematics ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 922 ◽  
Author(s):  
C. J. Luis Pérez
Keyword(s):  
Fuzzy Inference System ◽  
Electrical Discharge ◽  
Material Removal ◽  
Fuzzy Inference ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Operating Conditions ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Inference System

Technological tables are very important in electrical discharge machining to determine optimal operating conditions for process variables, such as material removal rate or electrode wear. Their determination is of great industrial importance and their experimental determination is very important because they allow the most appropriate operating conditions to be selected beforehand. These technological tables are usually employed for electrical discharge machining of steel, but their number is significantly less in the case of other materials. In this present research study, a methodology based on using a fuzzy inference system to obtain these technological tables is shown with the aim of being able to select the most appropriate manufacturing conditions in advance. In addition, a study of the results obtained using a fuzzy inference system for modeling the behavior of electrical discharge machining parameters is shown. These results are compared to those obtained from response surface methodology. Furthermore, it is demonstrated that the fuzzy system can provide a high degree of precision and, therefore, it can be used to determine the influence of these machining parameters on technological variables, such as roughness, electrode wear, or material removal rate, more efficiently than other techniques.

Reducing Electrode Wear Using Cryogenic Cooling during Electrical Discharge Machining

2009 ◽  
Vol 83-86 ◽  
pp. 672-679 ◽  
Author(s):  
Suleiman Abdulkareem ◽  
Ahsan Ali Khan ◽  
Mohamed Konneh
Keyword(s):  
Electrode Material ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Cryogenic Cooling ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Electrode Tool ◽  
Pulse On Time

In electrical discharge machining (EDM), material is removed by a series of electrical discharge between the electrode (tool) and the workpiece that develops a temperature of about 8,0000C to 12,0000C. Due to high temperature of the sparks, work material is melted and vapourized, at the same time the electrode material is also eroded by melting and vapourization. Electrodes wear (EW) process is quite similar to the material removal mechanism as the electrode and the workpiece are considered as a set of electrode in EDM. In the present study effort has been made to reduce EW by cooling, using liquid nitrogen during the EDM of titanium alloy. Investigation on the effect of cooling on electrode wear (EW), material removal rate (MRR) and surface roughness (Ra) of the workpiece was carried out. Current (I), pulse on-time (ton), pause off-time (toff) and voltage (v) were considered as the machining parameters. Design of experiment (DOE) was used to design the experimental works. Cooling of electrode by this technique reduced the melting and vapourization of electrode material and enhances electrode life. It was possible to reduce EW up to 27% by applying this technique while MRR and Ra were improved by 18% and 8% respectively.

Experimental Research on Technology of Ultrasonic Vibration Aided Electrical Discharge Machining (UEDM) in Gas

2006 ◽  
Vol 315-316 ◽  
pp. 81-84 ◽  
Author(s):  
Qin He Zhang ◽  
Jian Hua Zhang ◽  
Q.B. Zhang ◽  
Shu Peng Su
Keyword(s):  
Ultrasonic Vibration ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Electrode ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Environment Pollution ◽  
Dielectric Fluids

Ultrasonic vibration aided electrical discharge machining (UEDM) in gas is an electrical discharge machining (EDM) technology, in which gases such as air and oxygen are used as dielectrics and ultrasonic vibration is applied. UEDM in gas can avoid environment pollution, the most serious disadvantage of conventional EDM in kerosene-based oil or other dielectric fluids, and it is environmental-friendly. The technology also possesses virtues of wide applications, high machining efficiency and simple tool electrodes and so on. The principle of UEDM in gas is introduced in this paper. Experiments have been carried out to study the effects of machining parameters on material removal rate (MRR), surface roughness of the workpiece and tool electrode wear ratio (TWR), and the experiments results have also been analyzed.

Machining Feasibility of a New Developed Medium in Electrical Discharge Machining

2015 ◽  
Vol 656-657 ◽  
pp. 335-340 ◽  
Author(s):  
Fang Pin Chuang ◽  
Yan Cherng Lin ◽  
Hsin Min Lee ◽  
Han Ming Chow ◽  
A. Cheng Wang
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Environmentally Friendly ◽  
Industrial Applications ◽  
Deionized Water ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machining Characteristics

The environment issue and green machining technique have been induced intensive attention in recent years. It is urgently need to develop a new kind dielectric to meet the requirements for industrial applications. The aim of this study is to develop a novel dielectric using gas media immersed in deionized water for electrical discharge machining (EDM). The developed machining medium for EDM can fulfill the environmentally friendly issue and satisfy the demand of high machining performance. The experiments were conducted by this developed medium to investigate the effects of machining parameters on machining characteristics in terms of material removal rate (MRR) and surface roughness. The developed EDM medium revealed the potential to obtain a stabilizing progress with excellent machining performance and environmentally friendly feature.

The effect of magnesium content on drilling of Al-Mg-Ti alloy by hole electrical discharge machining process

2020 ◽  
Vol 235 (1-2) ◽  
pp. 125-133
Author(s):  
Omer Eyercioglu ◽  
Kursad Gov
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Magnesium Content ◽  
Machining Process ◽  
Electrode Wear ◽  
Ti Alloy ◽  
Ti Alloys ◽  
Mg Content

This study presents an experimental investigation of small hole electrical discharge machining of Al-Mg-Ti alloys. A series of drilling operations were carried out for exploring the effect of magnesium content. Holes of 2 mm diameter and 15 mm depth were drilled using tubular single-hole rotary brass electrodes. The rates of material removal and electrode wear, surface roughness, overcut, average recast layer thickness, taper height and angle were studied for Al-Mg-Ti alloys contain 2%, 4%, 6%, 8%, 10%, 12%, and 14% Mg. The results show that the material removal rate is increasing with increasing Mg content while the rate of electrode wear is almost unchanged. Due to decreasing the melting temperature of the Al-Mg-Ti alloy with increasing Mg content, more metal melts and vaporizes during electrical discharge machining drilling. Therefore, more overcut and taper, thicker white layer, and rougher surfaces were measured for higher Mg content.

Sign in / Sign up

Export Citation Format

Share Document