scholarly journals Experimental Investigation of the Influence of Wire Arc Additive Manufacturing on the Machinability of Titanium Parts

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 24 ◽  
Author(s):  
Unai Alonso ◽  
Fernando Veiga ◽  
Alfredo Suárez ◽  
Teresa Artaza
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Production Costs ◽  
Metallographic Analysis ◽  
Laminated Plate ◽  
Serrated Chip ◽  
Cross Sectional ◽  
Serrated Chip Formation ◽  
Wire Arc Additive Manufacturing ◽  
Finishing Machining

The manufacturing of titanium airframe parts involves significant machining and low buy-to-fly ratios. Production costs could be greatly reduced by the combination of an additive manufacturing (AM) process followed by a finishing machining operation. Among the different AM alternatives, wire arc additive manufacturing (WAAM) offers deposition rates of kg/h and could be the key for the production of parts of several meters economically. In this study, the influence of the manufacturing process of Ti6Al4V alloy on both its material properties and machinability is investigated. First, the mechanical properties of a workpiece obtained by WAAM were compared to those in a conventional laminated plate. Then, drilling tests were carried out in both materials. The results showed that WAAM leads to a higher hardness than laminated Ti6Al4V and satisfies the requirements of the standard in terms of mechanical properties. As a consequence, higher cutting forces, shorter chips, and lower burr height were observed for the workpieces produced by AM. Furthermore, a metallographic analysis of the chip cross-sectional area also showed that a serrated chip formation is also present during drilling of Ti6Al4V produced by WAAM. The gathered information can be used to improve the competitiveness of the manufacturing of aircraft structures in terms of production time and cost.

Wire arc additive manufacturing of thin-wall low-carbon steel parts: Microstructure and mechanical properties

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040154
Author(s):  
Van Thao Le ◽  
Tien Long Banh ◽  
Duc Toan Nguyen ◽  
Van Tao Le
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Heat Input ◽  
Low Carbon Steel ◽  
Production Costs ◽  
High Deposition Rate ◽  
Thin Wall ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) has received much attention for manufacturing metal parts with medium and large dimensions because of its high deposition rate and low production costs. In this study, the effects of the heat input on the microstructure formation of thin-wall low-carbon steel parts built by a WAAM process were addressed. The mechanical properties of built materials were also studied. The results indicate that the heat input significantly influences on the shape of built thin walls, but has slight effects on the microstructure evolution of built materials. The WAAM thin-wall low-carbon steel presents suitable microstructures and good tensile strengths (YS: 320 – 362 MPa, UTS: 429 – 479 MPa) that are adequate with industrial applications.

Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process

2021 ◽  
pp. 095440622199840
Author(s):  
Yashwant Koli ◽  
N Yuvaraj ◽  
Aravindan Sivanandam ◽  
Vipin
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Large Scale ◽  
High Deposition Rate ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Cold Metal Transfer ◽  
Geometrical Shapes ◽  
Wire Arc Additive Manufacturing

Nowadays, rapid prototyping is an emerging trend that is followed by industries and auto sector on a large scale which produces intricate geometrical shapes for industrial applications. The wire arc additive manufacturing (WAAM) technique produces large scale industrial products which having intricate geometrical shapes, which is fabricated by layer by layer metal deposition. In this paper, the CMT technique is used to fabricate single-walled WAAM samples. CMT has a high deposition rate, lower thermal heat input and high cladding efficiency characteristics. Humping is a common defect encountered in the WAAM method which not only deteriorates the bead geometry/weld aesthetics but also limits the positional capability in the process. Humping defect also plays a vital role in the reduction of hardness and tensile strength of the fabricated WAAM sample. The humping defect can be controlled by using low heat input parameters which ultimately improves the mechanical properties of WAAM samples. Two types of path planning directions namely uni-directional and bi-directional are adopted in this paper. Results show that the optimum WAAM sample can be achieved by adopting a bi-directional strategy and operating with lower heat input process parameters. This avoids both material wastage and humping defect of the fabricated samples.

scholarly journals Effect of Filler Metal Type on Microstructure and Mechanical Properties of Fabricated NiAl Bronze Alloy Using Wire Arc Additive Manufacturing System

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 513
Author(s):  
Jae Won Kim ◽  
Jae-Deuk Kim ◽  
Jooyoung Cheon ◽  
Changwook Ji
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Filler Metal ◽  
Gas Metal Arc Welding ◽  
Metal Wire ◽  
Cold Metal Transfer ◽  
Metal Type ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

This study observed the effect of filler metal type on mechanical properties of NAB (NiAl-bronze) material fabricated using wire arc additive manufacturing (WAAM) technology. The selection of filler metal type is must consider the field condition, mechanical properties required by customers, and economics. This study analyzed the bead shape for representative two kind of filler metal types use to maintenance and fabricated a two-dimensional bulk NAB material. The cold metal transfer (CMT) mode of gas metal arc welding (GMAW) was used. For a comparison of mechanical properties, the study obtained three specimens per welding direction from the fabricated bulk NAB material. In the tensile test, the NAB material deposited using filler metal wire A showed higher tensile strength and lower elongation (approx. +71 MPa yield strength, +107.1 MPa ultimate tensile strength, −12.4% elongation) than that deposited with filler metal wire B. The reason is that, a mixture of tangled fine α platelets and dense lamellar eutectoid α + κIII structure with β´ phases was observed in the wall made with filler metal wire A. On the other hand, the wall made with filler metal wire B was dominated by coarse α phases and lamellar eutectoid α + κIII structure in between.

scholarly journals Characterisation of a High-Performance Al–Zn–Mg–Cu Alloy Designed for Wire Arc Additive Manufacturing

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1610 ◽  
Author(s):  
Paulo J. Morais ◽  
Bianca Gomes ◽  
Pedro Santos ◽  
Manuel Gomes ◽  
Rudolf Gradinger ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
High Performance ◽  
Mechanical Performance ◽  
Fluorescence Analysis ◽  
Cold Metal Transfer ◽  
Direction Parallel ◽  
X Ray ◽  
Wire Arc Additive Manufacturing

Ever-increasing demands of industrial manufacturing regarding mechanical properties require the development of novel alloys designed towards the respective manufacturing process. Here, we consider wire arc additive manufacturing. To this end, Al alloys with additions of Zn, Mg and Cu have been designed considering the requirements of good mechanical properties and limited hot cracking susceptibility. The samples were produced using the cold metal transfer pulse advanced (CMT-PADV) technique, known for its ability to produce lower porosity parts with smaller grain size. After material simulations to determine the optimal heat treatment, the samples were solution heat treated, quenched and aged to enhance their mechanical performance. Chemical analysis, mechanical properties and microstructure evolution were evaluated using optical light microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray fluorescence analysis and X-ray radiography, as well as tensile, fatigue and hardness tests. The objective of this research was to evaluate in detail the mechanical properties and microstructure of the newly designed high-performance Al–Zn-based alloy before and after ageing heat treatment. The only defects found in the parts built under optimised conditions were small dispersed porosities, without any visible cracks or lack of fusion. Furthermore, the mechanical properties are superior to those of commercial 7xxx alloys and remarkably independent of the testing direction (parallel or perpendicular to the deposit beads). The presented analyses are very promising regarding additive manufacturing of high-strength aluminium alloys.

Sign in / Sign up

Export Citation Format

Share Document