scholarly journals Experimental and FEM Analysis of Void Closure in the Hot Cogging Process of Tool Steel

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 538 ◽  
Author(s):  
Marcin Kukuryk
Keyword(s):  
Hydrostatic Stress ◽  
Effective Strain ◽  
Three Dimensional ◽  
Stress Triaxiality ◽  
Fem Analysis ◽  
Experimental Tests ◽  
Reduction Ratio ◽  
Compression Process ◽  
Void Closure ◽  
Axial Defects

In the present study, a new complex methodology for the analysis the closure of voids and a new forging system were developed and tested. The efficiency of the forging parameters and the effective geometric shapes of anvils to improve void closure were determined. A new cogging process provided a complete closure of an ingot’s axial defects, as confirmed by experimental tests. The evolution behavior of these defects with different sizes was investigated during the hot cogging process by means of the professional plastic forming software Deform-3D. A comprehensive procedure was developed using the finite-element method (FEM) for the three-dimensional cogging process and laboratory experimentation to predict the degree of void closure. The hot multi-pass cogging process was used to eliminate void defects in the forgings so as to obtain sound products. In the compression process, the effects of the reduction ratio and forging ratio, the void size, and the types of anvil were discussed to obtain the effective elimination of a void. For the purpose of the assessment of the effectiveness of the void closure process, the following indices were introduced: the relative void volume evolution ratio, the relative void diameter ratio, and the internal void closure evaluation index. Moreover, the void closure process was assessed on the basis of stress triaxiality, hydrostatic stress, forging ratio, value of local effective strain around the void, and critical reduction ratio. The results of this research were complemented by experiments predicting the formation of fractures in the regions near the void and in the volume of the forging in the course of the cogging process. The comparison between the predicted and the experimental results showed a good agreement.

Analysis on Void Closure Behavior during Hot Open Die Forging

2007 ◽  
Vol 26-28 ◽  
pp. 69-72 ◽  
Author(s):  
Young Seon Lee ◽  
Y.C. Kwon ◽  
Yong Nam Kwon ◽  
Jung Hwan Lee ◽  
S.W. Lee ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Effective Strain ◽  
Fem Analysis ◽  
Void Closure ◽  
X Ray ◽  
Die Forging ◽  
Before And After ◽  
Measured Flow ◽  
Flow Stress Data ◽  
Open Die Forging

Internal voids have to be eliminated for defect-free in some open die forging. The FEM analysis is performed to investigate the overlap defect of cast ingots during cogging stage. The measured flow stress data were used to simulate the cogging process of cast ingot using the practical material properties. Also the numerical analysis of void closure is performed by using the DEFORMTM-3D. The calculated results of void closure behavior are compared with the measured results before and after upsetting, which are scanned by the X-ray scanner. From this result, the criteria for deformation amounts effect on the void closure were estimated into effective strain of 0.6 by the comparison of practical experiment and numerical analysis.

scholarly journals Characteristics of selected measures of stress triaxiality near the crack tip for 145Cr6 steel - 3D issues for stationary cracks

2020 ◽  
Vol 10 (1) ◽  
pp. 571-585
Author(s):  
Marcin Graba
Keyword(s):  
Finite Element Method ◽  
Three Dimensional ◽  
Stress Triaxiality ◽  
Crack Tip ◽  
Fem Analysis ◽  
Material Constant ◽  
Stress Fields ◽  
Material Characteristic ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

AbstractIn the paper the numerical analysis of the stress fields for 145Cr6 steel, near crack tip is presented, based on three-dimensional finite element method (FEM) analysis. The FEM analysis is focused on SEN(B) specimens with relative crack length a/W ≈ 0.30. In addition to the presentation of the normal components of the stress tensor, the paper presents selected measures of stress triaxiality parameters, measured for the value of the J-integral, corresponding to the experimentally determined fracture toughness, denoted as JIC, which is considered to be a material constant or material characteristic [1, 2]. Presented topic is a continuation of papers [3, 4],whichwere based on experimental analysis, presented in [5].

scholarly journals Investigation of Pressure Oscillation and Cavitation Characteristics for Submerged Self-Resonating Waterjet

2021 ◽  
Vol 11 (15) ◽  
pp. 6972
Author(s):  
Lihua Cui ◽  
Fei Ma ◽  
Tengfei Cai
Keyword(s):  
Sudden Change ◽  
Three Dimensional ◽  
Pressure Oscillation ◽  
Experimental Tests ◽  
Low Pressure ◽  
The Self ◽  
Two Phase ◽  
Cavitation Phenomenon ◽  
Pressure Zone ◽  
Unsteady Characteristics

The cavitation phenomenon of the self-resonating waterjet for the modulation of erosion characteristics is investigated in this paper. A three-dimensional computational fluid dynamics (CFD) model was developed to analyze the unsteady characteristics of the self-resonating jet. The numerical model employs the mixture two-phase model, coupling the realizable turbulence model and Schnerr–Sauer cavitation model. Collected data from experimental tests were used to validate the model. Results of numerical simulations and experimental data frequency bands obtained by the Fast Fourier transform (FFT) method were in very good agreement. For better understanding the physical phenomena, the velocity, the pressure distributions, and the cavitation characteristics were investigated. The obtained results show that the sudden change of the flow velocity at the outlet of the nozzle leads to the forms of the low-pressure zone. When the pressure at the low-pressure zone is lower than the vapor pressure, the cavitation occurs. The flow field structure of the waterjet can be directly perceived through simulation, which can provide theoretical support for realizing the modulation of the erosion characteristics, optimizing nozzle structure.

scholarly journals Experimental & FEM Analysis of Orthodontic Mini-Implant Design on Primary Stability

2021 ◽  
Vol 11 (12) ◽  
pp. 5461
Author(s):  
Elmedin Mešić ◽  
Enis Muratović ◽  
Lejla Redžepagić-Vražalica ◽  
Nedim Pervan ◽  
Adis J. Muminović ◽  
...  
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Primary Stability ◽  
Fem Analysis ◽  
Implant Design ◽  
Special Focus ◽  
Engineering System ◽  
Mini Implants ◽  
Pull Out ◽  
Computer Aided

The main objective of this research is to establish a connection between orthodontic mini-implant design, pull-out force and primary stability by comparing two commercial mini-implants or temporary anchorage devices, Tomas®-pin and Perfect Anchor. Mini-implant geometric analysis and quantification of bone characteristics are performed, whereupon experimental in vitro pull-out test is conducted. With the use of the CATIA (Computer Aided Three-dimensional Interactive Application) CAD (Computer Aided Design)/CAM (Computer Aided Manufacturing)/CAE (Computer Aided Engineering) system, 3D (Three-dimensional) geometric models of mini-implants and bone segments are created. Afterwards, those same models are imported into Abaqus software, where finite element models are generated with a special focus on material properties, boundary conditions and interactions. FEM (Finite Element Method) analysis is used to simulate the pull-out test. Then, the results of the structural analysis are compared with the experimental results. The FEM analysis results contain information about maximum stresses on implant–bone system caused due to the pull-out force. It is determined that the core diameter of a screw thread and conicity are the main factors of the mini-implant design that have a direct impact on primary stability. Additionally, stresses generated on the Tomas®-pin model are lower than stresses on Perfect Anchor, even though Tomas®-pin endures greater pull-out forces, the implant system with implemented Tomas®-pin still represents a more stressed system due to the uniform distribution of stresses with bigger values.

scholarly journals An Immunoinformatics Approach for SARS-CoV-2 in Latam Populations and Multi-Epitope Vaccine Candidate Directed Towards the World’s Population

Vaccines ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 581
Author(s):  
Andrés Felipe Cuspoca ◽  
Laura Lorena Díaz ◽  
Alvaro Fernando Acosta ◽  
Marcela Katherine Peñaloza ◽  
Yardany Rafael Méndez ◽  
...  
Keyword(s):  
B Lymphocyte ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Health Crisis ◽  
Public Health Crisis ◽  
Histocompatibility Complex ◽  
Potential Vaccine ◽  
Lymphocyte Responses ◽  
Socioeconomic Consequences ◽  
Epitope Candidate

The coronavirus pandemic is a major public health crisis affecting global health systems with dire socioeconomic consequences, especially in vulnerable regions such as Latin America (LATAM). There is an urgent need for a vaccine to help control contagion, reduce mortality and alleviate social costs. In this study, we propose a rational multi-epitope candidate vaccine against SARS-CoV-2. Using bioinformatics, we constructed a library of potential vaccine peptides, based on the affinity of the most common major human histocompatibility complex (HLA) I and II molecules in the LATAM population to predict immunological complexes among antigenic, non-toxic and non-allergenic peptides extracted from the conserved regions of 92 proteomes. Although HLA-C, had the greatest antigenic peptide capacity from SARS-CoV-2, HLA-B and HLA-A, could be more relevant based on COVID-19 risk of infection in LATAM countries. We also used three-dimensional structures of SARS-CoV-2 proteins to identify potential regions for antibody production. The best HLA-I and II predictions (with increased coverage in common alleles and regions evoking B lymphocyte responses) were grouped into an optimized final multi-epitope construct containing the adjuvants Beta defensin-3, TpD, and PADRE, which are recognized for invoking a safe and specific immune response. Finally, we used Molecular Dynamics to identify the multi-epitope construct which may be a stable target for TLR-4/MD-2. This would prove to be safe and provide the physicochemical requirements for conducting experimental tests around the world.

scholarly journals On the Post-Processing of 3D-Printed ABS Parts

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1559
Author(s):  
Mohammad Reza Khosravani ◽  
Jonas Schüürmann ◽  
Filippo Berto ◽  
Tamara Reinicke
Keyword(s):  
Surface Treatment ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fracture Load ◽  
Post Processing ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printed

Application of Additive Manufacturing (AM) has significantly increased in the past few years. AM also known as three-dimensional (3D) printing has been currently used in fabrication of prototypes and end-use products. Considering the new applications of additively manufactured components, it is necessary to study structural details of these parts. In the current study, influence of a post-processing on the mechanical properties of 3D-printed parts has been investigated. To this aim, Acrylonitrile Butadiene Styrene (ABS) material was used to produce test coupons based on the Fused Deposition Modeling (FDM) process. More in deep, a device was designed and fabricated to fix imperfection and provide smooth surfaces on the 3D-printed ABS specimens. Later, original and treated specimens were subjected to a series of tensile loads, three-point bending tests, and water absorption tests. The experimental tests indicated fracture load in untreated dog-bone shaped specimen was 2026.1 N which was decreased to 1951.7 N after surface treatment. Moreover, the performed surface treatment was lead and decrease in tensile strength from 29.37 MPa to 26.25 MPa. Comparison of the results confirmed effects of the surface modification on the fracture toughness of the examined semi-circular bending components. Moreover, a 3D laser microscope was used for visual investigation of the specimens. The documented results are beneficial for next designs and optimization of finishing processes.

scholarly journals Numerical Analysis of the Perforated Steel Sheets Under Uni-Axial Tensile Force

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 632 ◽  
Author(s):  
Ahmed M. Sayed
Keyword(s):  
Load Capacity ◽  
Tensile Force ◽  
Three Dimensional ◽  
Tensile Load ◽  
Experimental Tests ◽  
Strain Engineering ◽  
Uniaxial Tensile ◽  
Fe Model ◽  
Stress Strain ◽  
Steel Sheets

The perforated steel sheets have many uses, so they should be studied under the influence of the uniaxial tensile load. The presence of these holes in the steel sheets certainly affects the mechanical properties. This paper aims at studying the behavior of the stress-strain engineering relationships of the perforated steel sheets. To achieve this, the three-dimensional finite element (FE) model is mainly designed to investigate the effect of this condition. Experimental tests were carried out on solid specimens to be used in the test of model accuracy of the FE simulation. Simulation testing shows that the FE modeling revealed the ability to calculate the stress-strain engineering relationships of perforated steel sheets. It can be concluded that the effect of a perforated rhombus shape is greater than the others, and perforated square shape has no effect on the stress-strain engineering relationships. The efficiency of the perforated staggered or linearly distribution shapes with the actual net area on the applied loads has the opposite effect, as it reduces the load capacity for all types of perforated shapes. Despite the decrease in load capacity, it improves the properties of the steel sheets.

Three Dimensional Numerical Analyses of Bridge Piled-Raft Foundation under Riverbed Erosion

2012 ◽  
Vol 178-181 ◽  
pp. 2373-2377 ◽  
Author(s):  
Wen Tsung Liu ◽  
Yi Yi Li
Keyword(s):  
Bearing Capacity ◽  
Three Dimensional ◽  
Fem Analysis ◽  
Bridge Piers ◽  
Piled Raft Foundation ◽  
River Erosion ◽  
Dimensional Finite Element ◽  
The Face ◽  
Three Dimensional Finite Element

From the 921 earthquake to the major typhoons, including the Morakot typhoon, they damaged original landscape of rivers in Taiwan. In recent years, it alleged that abutment bridge exposed to the most serious security problems. Because of bridge piers in addition to the face of long-term river erosion, the flood on the pier will produce localized erosion near the bridge. The pier will be due to inadequate bearing capacity, resulting in subsidence, displacement, bridge version accompanied by tilting and even caving. The river erosion of soil around the piers deposits and production of contraction will often reduce the bearing capacity. Therefore, how to accurately estimate the scour depth, calculate piers to withstand water impact and analyses its stability for preventing injuries in the first place is the current pressing issues. In this study, three-dimensional finite element method (FEM) analysis program Plaxis 3D foundation is used. Polaris second bridge is selected for analysis. Based on local scouring of the model and various numerical variable conditions, the parameter of bridge pier is studied.

Investigations of The Hybrid Effects of The Operational Parameters In The Radial Forging Process Based On The Validation of The Hardness Test

2022 ◽  
Author(s):  
Saeed Darki ◽  
Evgeniy Yurevich Raskatov
Keyword(s):  
Effective Strain ◽  
Three Dimensional ◽  
Hardness Test ◽  
Radial Forging ◽  
Operational Parameters ◽  
Three Dimensional Model ◽  
Temperature Changes ◽  
Forging Process ◽  
Specimen Tube ◽  
Radial Forging Process

Abstract In this study, considering all the parameters in radial forging and a three-dimensional model has been simulated using the finite element method. By implementing an elastoplastic state for the specimen tube, parameters such as friction type, residual stress distribution, effective strain distribution, material flow velocity and its effect on the neutral plate and the distribution of force in the die have been studied and analyzed. The effects of angle on the quality and characteristics of the specimen and the longevity of the die have also been obtained. Experimental results have been used to confirm the accuracy of the simulation. The results of the hardness test after forging were compared with the simulation results. Good agreement between the results indicates the accuracy of the simulation in terms of hardness. Therefore, this validation allows confirming the other obtained results for the analysis and prediction of various components in the forging process. After the validation and confirmation of the results through the hardness test, the hardness distribution was obtained by considering temperature changes and the effective strain on the specimen.

Sign in / Sign up

Export Citation Format

Share Document