scholarly journals Synthesis and Characterization of Partially Renewable Oleic Acid-Based Ionomers for Proton Exchange Membranes

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 130
Author(s):  
Carlos Corona-García ◽  
Alejandro Onchi ◽  
Arlette A. Santiago ◽  
Araceli Martínez ◽  
Daniella Esperanza Pacheco-Catalán ◽  
...  
Keyword(s):  
Oleic Acid ◽  
Proton Conductivity ◽  
Electrochemical Impedance ◽  
Proton Exchange Membranes ◽  
Proton Exchange ◽  
Molar Ratio ◽  
Aromatic Diamines ◽  
Chemical Structures ◽  
Long Chain

The future availability of synthetic polymers is compromised due to the continuous depletion of fossil reserves; thus, the quest for sustainable and eco-friendly specialty polymers is of the utmost importance to ensure our lifestyle. In this regard, this study reports on the use of oleic acid as a renewable source to develop new ionomers intended for proton exchange membranes. Firstly, the cross-metathesis of oleic acid was conducted to yield a renewable and unsaturated long-chain aliphatic dicarboxylic acid, which was further subjected to polycondensation reactions with two aromatic diamines, 4,4′-(hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline and 4,4′-diamino-2,2′-stilbenedisulfonic acid, as comonomers for the synthesis of a series of partially renewable aromatic-aliphatic polyamides with an increasing degree of sulfonation (DS). The polymer chemical structures were confirmed by Fourier transform infrared (FTIR) and nuclear magnetic resonance (1H, 13C, and 19F NMR) spectroscopy, which revealed that the DS was effectively tailored by adjusting the feed molar ratio of the diamines. Next, we performed a study involving the ion exchange capacity, the water uptake, and the proton conductivity in membranes prepared from these partially renewable long-chain polyamides, along with a thorough characterization of the thermomechanical and physical properties. The highest value of the proton conductivity determined by electrochemical impedance spectroscopy (EIS) was found to be 1.55 mS cm−1 at 30 °C after activation of the polymer membrane.

Preparation and Characterization of Radiation Grafted Proton Exchange Membranes of LLDPE

2010 ◽  
Vol 123-125 ◽  
pp. 1091-1094
Author(s):  
Sabia Sultana ◽  
Mubarak A. Khan ◽  
Nazia Rahman ◽  
Maksudur R. Khan
Keyword(s):  
Irradiation Time ◽  
Low Cost ◽  
Proton Exchange Membranes ◽  
Exchange Capacity ◽  
Proton Exchange ◽  
Membrane Properties ◽  
Molar Ratio ◽  
Grafting Technique ◽  
Exchange Membrane

As the demand for radiation grafted Proton Exchange Membranes (PEMs) is intensifying, interest in new materials for preparing PEM is rapidly increasing. This study aims to develop sustainable low-cost highly conductive PEM. In our work we have prepared linear low density polyethylene (LLDPE) based PEM and investigated the membrane characteristics. Simultaneous radiation grafting technique has been applied to introduce the styrene monomer onto the LLDPE films by UV radiation under atmospheric circumstances. It has been observed that grafting yield gradually changes depending on the irradiation time and monomer molar ratio. We have performed experiments to assess certain membrane properties, such as water uptake, ion exchange capacity with respect to their applicability in fuel cells. Our experimental results demonstrate the effectiveness of LLDPE based PEM as a cation exchange membrane.

Synthesis and Characterization of Sulfonated Polybenzoxazole for High Temperature Proton Exchange Membranes

2013 ◽  
Vol 821-822 ◽  
pp. 1261-1265 ◽  
Author(s):  
Wen Feng Wang ◽  
Rong Rong Hao ◽  
Sheng Lin Yang ◽  
Jun Hong Jin ◽  
Guang Li
Keyword(s):  
High Temperature ◽  
Proton Conductivity ◽  
Polyphosphoric Acid ◽  
Theoretical Calculations ◽  
Proton Exchange Membranes ◽  
Proton Exchange ◽  
Sulfonation Degree ◽  
Monosodium Salt ◽  
Thermal Stable

Sulfonated Polybenzoxazoles (sPBO) with sulfonation degree ranging from 10% to 30% were synthesized from 4,6-diaminoresorcinol dihydrochloride (DAR), terephthalic acid (TPA), 5-sulfoisophthalic acid monosodium salt (SIPA) by direct polycondensation in polyphosphoric acid (PPA). The structures of sPBOs were verified by FTIR and elemental analysis. The values of inherent viscosity ranged from 2.56 to 1.12 dL/g and decreased with the increasing of sulfonation degree. TGA analysis showed sPBOs were thermal stable up to nearly 250°C. sPBO/PPA polymerization solution were hot pressed directly to form PPA doped sPBO membranes since sPBO was insouble in common solvents. The PPA doping level was about 340%(wt) per gram of sPBOs by theoretical calculations. The tensile strength of PPA doped sPBOs membrances ranged from 9.1 to 3.2 Mpa. At high temperature, sPBO membranes showed excellent proton conductivity. For instance, sPBO membrane with a sulfonation degree of 10% exhibited a proton conductivity of 0.123 S/cm at 170°C.The experimental results indicated sPBO are promising for proton exchange membranes for high temperature proton exchange membranes.

A Study of the Nitrogen-Containing Heterocycles on Copolyimide Properties for Proton Exchange Membranes

2013 ◽  
Vol 401-403 ◽  
pp. 563-566 ◽  
Author(s):  
Yu Han Li ◽  
Wei Jian Wang ◽  
Yu Fei Chen ◽  
Lei Wang
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Proton Conductivity ◽  
Water Uptake ◽  
Main Chain ◽  
Proton Exchange Membranes ◽  
Proton Exchange ◽  
Membrane Properties ◽  
Dimensional Changes ◽  
Sulfonated Polyimide

Containing pyrimidine and pyridine monomers were incorporated respectively into the main chain of a sulfonated polyimide in order to investigate the effect of nitrogen-containing heterocycles on membrane properties such as water uptake and proton conductivity. With increasing content of the nitrogen-containing heterocycles, water uptake of membranes and dimensional changes remarkable decrease. The copolymer showed higher thermal stability (desulfonation temperature up to 330 °C) and reasonable good mechanical properties. These membranes also showed higher proton conductivity, which was comparable or even higher than Nafion 117.

scholarly journals Sulfonated Binaphthyl-Containing Poly(arylene ether ketone)s with Rigid Backbone and Excellent Film-Forming Capability for Proton Exchange Membranes

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1287 ◽  
Author(s):  
Wenmeng Zhang ◽  
Shaoyun Chen ◽  
Dongyang Chen ◽  
Zhuoliang Ye
Keyword(s):  
Mechanical Properties ◽  
Proton Conductivity ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Thermal Stabilities ◽  
Chemical Structures ◽  
Arylene Ether ◽  
Film Forming ◽  
Ether Ketone ◽  
Microscopic Morphology

Sterically hindered (S)-1,1′-binaphthyl-2,2′-diol had been successfully copolymerized with 4,4′-sulfonyldiphenol and 4,4′-difluorobenzophenone to yield fibrous poly(arylene ether ketone)s (PAEKs) containing various amounts of binaphthyl unit, which was then selectively and efficiently sulfonated using ClSO3H to yield sulfonated poly(arylene ether ketone)s (SPAEKs) with ion exchange capacities (IECs) ranging from 1.40 to 1.89 mmol·g−1. The chemical structures of the polymers were confirmed by 2D 1H–1H COSY NMR and FT-IR. The thermal properties, water uptake, swelling ratio, proton conductivity, oxidative stability and mechanical properties of SPAEKs were investigated in detail. It was found that the conjugated but non-coplanar structure of binaphthyl unit endorsed excellent solubility and film-forming capability to SPAEKs. The SPAEK-50 with an IEC of 1.89 mmol·g−1 exhibited a proton conductivity of 102 mS·cm−1 at 30 °C, much higher than that of the state-of-the-art Nafion N212 membrane and those of many previously reported aromatic analogs, which may be attributed to the likely large intrinsic free volume of SPAEKs created by the highly twisted chain structures and the desirable microscopic morphology. Along with the remarkable water affinity, thermal stabilities and mechanical properties, the SPAEKs were demonstrated to be promising proton exchange membrane (PEM) candidates for potential membrane separations.

scholarly journals PEMBUATAN DAN KARAKTERISASI MEMBRAN KOMPOSIT KITOSAN-SODIUM ALGINAT TERFOSFORILASI SEBAGAI PROTON EXCHANGE MEMBRANE FUEL CELL (PEMFC)

2016 ◽  
Vol 1 (1) ◽  
pp. 14
Author(s):  
Siti Wafiroh ◽  
Suyanto Suyanto ◽  
Yuliana Yuliana
Keyword(s):  
Fuel Cell ◽  
Sodium Alginate ◽  
Proton Conductivity ◽  
Composite Membrane ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Methanol Permeability ◽  
Water Swelling ◽  
Exchange Membrane

AbstrakDi era globalisasi ini, kebutuhan bahan bakar fosil semakin meningkat dan ketersediannya semakin menipis. Oleh karena itu, dibutuhkan bahan bakar alternatif seperti Proton Exchange Membrane Fuel Cell (PEMFC). Tujuan dari penelitian ini adalah membuat dan mengkarakterisasi membran komposit kitosan-sodium alginat dari rumput laut coklat (Sargassum sp.) terfosforilasi sebagai Proton Exchange Membrane Fuel Cell (PEMFC). PEM dibuat dengan 4 variasi perbandingan konsentrasi antara kitosan dengan sodium alginat 8:0, 8:1, 8:2, dan 8:4 (b/b). Membran komposit kitosan-sodium alginat difosforilasi dengan STPP 2N. Karakterisasi PEM meliputi: uji tarik, swelling air, kapasitas penukar ion, FTIR, SEM, permeabilitas metanol, dan konduktivitas proton. Berdasarkan hasil analisis tersebut, membran yang optimal adalah perbandingan 8:1 (b/b) dengan nilai modulus young sebesar 0,0901 kN/cm2, swelling air sebesar 19,14 %, permeabilitas metanol sebesar 72,7 x 10-7, dan konduktivitas proton sebesar 4,7 x 10-5 S/cm. Membran komposit kitosan-sodium alginat terfosforilasi memiliki kemampuan yang cukup baik untuk bisa diaplikasikan sebagai membran polimer elektrolit dalam PEMFC. Kata kunci: kitosan, sodium alginat, terfosforilasi, PEMFC  AbstractIn this globalization era, the needs of fossil fuel certainly increases, but its providence decreases. Therefore, we need alternative fuels such as Proton Exchange Membrane Fuel Cell (PEMFC). The purpose of this study is preparationand characterization of phosphorylated chitosan-sodium alginate composite membrane from brown seaweed (Sargassum sp.) as Proton Exchange Membrane Fuel Cell (PEMFC). PEM is produced with 4 variations of concentration ratio between chitosan and sodium alginate 8:0, 8:1, 8:2, and 8:4 (w/w). Chitosan-sodium alginate composite membrane phosphorylated with 2 N STPP. The characterization of PEM include: tensile test, water swelling, ion exchange capacity, FTIR, SEM, methanol permeability, and proton conductivity. Based on the analysis result, the optimal membrane is ratio of 8:1 (w/w) with the value of Young’s modulus about 0.0901 kN/cm2, water swelling at 19.14%, methanol permeability about 72.7 x 10-7, and proton conductivity about 4.7 x 10-5 S/cm. The phosphorylated chitosan-sodium alginate composite membrane has good potentials for the application of the polymer electrolyte membrane in PEMFC. Keywords: chitosan, sodium alginate, phosphorylated, PEMFC

scholarly journals Recent Progress in the Development of Aromatic Polymer-Based Proton Exchange Membranes for Fuel Cell Applications

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1061 ◽  
Author(s):  
Raja Rafidah R. S. ◽  
Rashmi W. ◽  
Khalid M. ◽  
Wong W. Y. ◽  
Priyanka J.
Keyword(s):  
Fuel Cells ◽  
Fuel Cell ◽  
Proton Conductivity ◽  
Elevated Temperatures ◽  
Proton Exchange Membranes ◽  
Proton Exchange ◽  
Operating Conditions ◽  
Polymer Chains ◽  
Membrane Electrode ◽  
Aryl Ether

Proton exchange membranes (PEMs) play a pivotal role in fuel cells; conducting protons from the anode to the cathode within the cell’s membrane electrode assembles (MEA) separates the reactant fuels and prevents electrons from passing through. High proton conductivity is the most important characteristic of the PEM, as this contributes to the performance and efficiency of the fuel cell. However, it is also important to take into account the membrane’s durability to ensure that it canmaintain itsperformance under the actual fuel cell’s operating conditions and serve a long lifetime. The current state-of-the-art Nafion membranes are limited due to their high cost, loss of conductivity at elevated temperatures due to dehydration, and fuel crossover. Alternatives to Nafion have become a well-researched topic in recent years. Aromatic-based membranes where the polymer chains are linked together by aromatic rings, alongside varying numbers of ether, ketone, or sulfone functionalities, imide, or benzimidazoles in their structures, are one of the alternatives that show great potential as PEMs due totheir electrochemical, mechanical, and thermal strengths. Membranes based on these polymers, such as poly(aryl ether ketones) (PAEKs) and polyimides (PIs), however, lack a sufficient level of proton conductivity and durability to be practical for use in fuel cells. Therefore, membrane modifications are necessary to overcome their drawbacks. This paper reviews the challenges associated with different types of aromatic-based PEMs, plus the recent approaches that have been adopted to enhance their properties and performance.

Sign in / Sign up

Export Citation Format

Share Document