Optical Fiber Cladding SPR Sensor Based on Core-Shift Welding Technology

The typical structure of an optical fiber surface plasmon resonance (SPR) sensor, which has been widely investigated, is to produce the SPR phenomenon by the transmission of light in a fiber core. The traditional method is to peel off the fiber cladding by complex methods such as corrosion, polishing, and grinding. In this paper, the transmitted light of a single-mode fiber is injected into three kinds of fiber cladding by core-shift welding technology to obtain the evanescent field directly between the cladding and the air interface and to build the Kretschmann structure by plating with a 50-nm gold film. The SPR sensing phenomenon is realized in three kinds of fiber cladding of a single-mode fiber, a graded-index multimode fiber, and a step-index multimode fiber. For the step-index multimode fiber cladding SPR sensor, all the light field energy is coupled to the cladding, leading to no light field in the fiber core, the deepest resonance valley, and the narrowest full width at half maximum. The single-mode fiber cladding SPR sensor has the highest sensitivity, and the mean sensitivity of the probe reaches 2538 nm/RIU (refractive index unit) after parameter optimization.

Download Full-text

Determination of temperature and strain by a compact optical fiber Mach-Zehnder interferometer (MZI) composed of a single-mode fiber (SMF), seven core fiber (SCF), and multimode fiber (MMF) with a fiber Bragg grating (FBG)

Instrumentation Science & Technology ◽

10.1080/10739149.2021.1884092 ◽

2021 ◽

pp. 1-13

Author(s):

Zhaojun Liu ◽

Lianqing Zhu ◽

Lidan Lu ◽

Chunmei Shangguan ◽

Dongliang Zhang ◽

...

Keyword(s):

Optical Fiber ◽

Fiber Bragg Grating ◽

Single Mode ◽

Single Mode Fiber ◽

Zehnder Interferometer ◽

Bragg Grating ◽

Multimode Fiber ◽

Core Fiber ◽

Mach Zehnder Interferometer

Download Full-text

Microdrilled tapers to enhance optical fiber lasers for sensing

Scientific Reports ◽

10.1038/s41598-021-00046-7 ◽

2021 ◽

Vol 11 (1) ◽

Author(s):

R. A. Perez-Herrera ◽

M. Bravo ◽

P. Roldan-Varona ◽

D. Leandro ◽

L. Rodriguez-Cobo ◽

...

Keyword(s):

Optical Fiber ◽

Optical Fibers ◽

Fiber Lasers ◽

Signal To Noise Ratio ◽

Power Level ◽

Single Mode ◽

Optical Signal ◽

Single Mode Fiber ◽

Output Power Level ◽

Linear Cavity

AbstractIn this work, an experimental analysis of the performance of different types of quasi-randomly distributed reflectors inscribed into a single-mode fiber as a sensing mirror is presented. These artificially-controlled backscattering fiber reflectors are used in short linear cavity fiber lasers. In particular, laser emission and sensor application features are analyzed when employing optical tapered fibers, micro-drilled optical fibers and 50 μm-waist or 100 μm-waist micro-drilled tapered fibers (MDTF). Single-wavelength laser with an output power level of about 8.2 dBm and an optical signal-to-noise ratio of 45 dB were measured when employing a 50 μm-waist micro-drilled tapered optical fiber. The achieved temperature sensitivities were similar to those of FBGs; however, the strain sensitivity improved more than one order of magnitude in comparison with FBG sensors, attaining slope sensitivities as good as 18.1 pm/με when using a 50 μm-waist MDTF as distributed reflector.

Download Full-text

3D modeling of multimode and single mode fiber

Indonesian Journal of Electrical Engineering and Computer Science ◽

10.11591/ijeecs.v16.i3.pp1398-1406 ◽

2019 ◽

Vol 16 (3) ◽

pp. 1398

Author(s):

Murizah Kassim ◽

Ahmad Syahir Arif Mohd Zaid ◽

Azlina Idris ◽

Shahrani Shahbudin ◽

Roslina Mohamad ◽

...

Keyword(s):

Fiber Optics ◽

3D Modeling ◽

Service Providers ◽

Single Mode ◽

Single Mode Fiber ◽

Infrastructure Development ◽

Multimode Fiber ◽

Internet Service ◽

Fiber Technology ◽

Technical Specifications

<span>This paper presents a design of 3D modeling of Multimode and Single Mode Fiber using SolidWorks. Fiber technology is essential that presents optical fiber is the fastest optical cable laid by Internet Service Providers in network communication. The current design of both fibers has less detail animation on technical specifications of light propagations and cladding. Thus, characterization difficulties occur between this two fiber optics cables. It also has less promotion in media publications such as 3D model design as guidance to users. This paper presents details on 3D modeling of multimode mode and single mode fiber specifications held in the industry market. A 3D design with SolidWorks and comparison of both fiber characteristics are presented. Based on the 3D designed model, users are analyzed on their perspective and searching information which benefits telecommunication’s company. Technical calculations like core-cladding diameter ratio in microns are animated. The propagation of light in 3D single mode and multimode fiber is simulated using SolidWorks animator that presents it real fiber conditions. Result presents 10 most country searching used of both fiber cables and the difference in users search for both cables. A number of user’s search presents 3% more of multimode than single mode fiber search cases. This research is significant in presenting an animator of single and multimode fiber to users of network infrastructure development especially network developers and Telecommunications Company which can present it lively with animator transitions.</span>

Download Full-text