scholarly journals Analyzing the Basic Properties and Environmental Footprint Reduction Effects of Highly Sulfated Calcium Silicate Cement

2021 ◽  
Vol 13 (14) ◽  
pp. 7540
Author(s):  
Hyeon-Soo Kim ◽  
Ik Kim ◽  
Wan-hee Yang ◽  
Soo-Young Moon ◽  
Ji-Young Lee

In South Korea, efforts to reduce carbon dioxide emissions and environmental impacts from the perspective of life cycle assessment (LCA) are important because of the implementation of zero-energy building certification for public buildings and the promotion of net-zero policy. Therefore, it is critical to develop cement alternatives with low embodied energy and less environmental impact. In this study, the applicability of “highly sulfated calcium silicate cement (HSCSC),” an eco-friendly binder developed by our research team, was investigated. Its basic properties and environmental footprint reduction effects were examined in comparison with ordinary Portland cement (OPC) and Portland blast furnace slag cement (PBSC). The environmental impacts of the HSCSC were analyzed using the LCA method. The results confirmed that HSCSC can be considered an excellent alternative to conventional OPC or PBSC in certain areas as an eco-friendly binder that can reduce carbon dioxide emissions and environmental impacts. Moreover, compared to OPC and PBSC, the probability of HSCSC affecting the human body is extremely low. The results of this study may contribute to the development and practical use of cements that minimize climate impacts, as well as improve the efficacy of future research on embodied energy saving.

Author(s):  
E. A. Alabushev ◽  
I. S. Bersenev ◽  
V. V. Bragin ◽  
A. A. Stepanova

The Paris Agreement, adopted in December of 2015 at the 21st session of the UNFCCC Conference of the Parties and effected from November of 2016, coordinates the efforts of states to reduce greenhouse gas (GHG) emissions, including carbon dioxide. One of its largest emitters to the atmosphere is the metallurgical industry. Among the proposed ways to reduce carbon dioxide emissions is the widespread use of hydrogen in the ferrous metallurgy. An overview of the problems that the ferrous metallurgy will face when replacing carbon-containing fuels with hydrogen is presented. It was noted that the use of hydrogen in the ferrous metallurgy contains such technological risks as high cost in comparison with currently used fuels and reducing agents; explosion hazard and corrosion activity, the need for a radical reconstruction of thermal units when using hydrogen instead of traditional for the ferrous metallurgy natural, coke and blast furnace gases, as well as solid fuels. It is shown that minimizing these risks is not always possible or economically feasible, and the result of using hydrogen in the ferrous metallurgy instead of carbon-containing fuel from the point of view of reducing greenhouse gas emissions may be low with a significant increase of economic and social risks.


Author(s):  
Courtney E. Grosvenor ◽  
Melissa C. Lott ◽  
Michael E. Webber

The impacts of the U.S. transportation and electricity generation sectors include air emissions and water consumption. Information and communication technologies (ICT) such as advanced video teleconferencing have the potential to displace some activities that have historically required transportation. While ICT can reduce environmental impacts compared to transportation options in many cases, there are non-obvious environmental trade-offs associated with replacing transportation with ICT. These tradeoffs are the consequence of many factors, including the particular local electricity mix, meeting duration, number of meeting participants, travel distances, travel modes, motive transport conversion technologies, and transport fuels. Identifying and quantifying these trade-offs is the focus of this research. For this study, a nomenclature and methodology were developed to compare environmental trade-offs associated with transportation and ICT. The nomenclature was designed to facilitate side-by-side comparison of the environmental impacts of travel and ICT and to allow expansion of the nomenclature for future study. The methodology considered a variety of conversion technologies for motive transport including spark-ignition, compression-ignition, fuel cells, and electric motors. Both conventional and developing fuels were considered including gasoline, ethanol, diesel, biodiesel, natural gas, hydrogen, and electricity. Likewise, electricity consumption for ICT included both traditional and developing electricity generation technologies. Carbon dioxide emissions and water consumption for ICT were assessed for comparison with transportation in a case study that demonstrated use of this methodology by considering three distinct scenarios for a particular business meeting: 1. Two meeting attendees travel to the meeting by diesel city bus while two travel in a private vehicle. 2. All four meeting attendees travel by private vehicle powered by compressed natural gas. 3. The four meeting attendees do not travel, but instead meet their clients virtually via ICT. The case study analyzed in this manuscript considers only the water and carbon dioxide impacts, but the nomenclature developed allows future expansion for analysis of other greenhouse gases. The three scenarios revealed that, compared to short travel distances, use of ICT does not always generate fewer carbon dioxide emissions. Depending on the mode of electricity generation, travel proved to be preferable from an emissions standpoint for scenarios in which travel distances were small. However, in cases that required long distances to travel, ICT often allowed businesses and individuals to reduce their environmental impacts, especially if electric power generation in that location utilized large amounts of relatively low-emissions technologies such as hydroelectric dams, wind, solar, and nuclear. Finally, it should be noted that, in addition to comparing ICT and travel impacts, this methodology can be used to calculate the environmental tradeoffs of various transportation options when travel is a necessity.


2011 ◽  
Vol 23 (6) ◽  
pp. 556-566 ◽  
Author(s):  
Ramon Farreny ◽  
Jordi Oliver-Solà ◽  
Machiel Lamers ◽  
Bas Amelung ◽  
Xavier Gabarrell ◽  
...  

AbstractThe increase of tourism to the Antarctic continent may entail not only local but also global environmental impacts. These latter impacts, which are mainly caused by transport, have been generally ignored. As a result, there is a lack of data on the global impacts of Antarctic tourism in terms of energy consumption and carbon dioxide emissions. This paper presents and applies a methodology for quantifying CO2 emissions, both for the Antarctic vessel fleet as a whole and per passenger (both per trip and per day). The results indicate that the average tourist trip to Antarctica results in 5.44 t of CO2 emissions per passenger, or 0.49 t per passenger and day. Approximately 70% of these emissions are attributable to cruising and 30% to flying, which highlights the global environmental relevance of local transport for this type of tourism.


Author(s):  
Angela Pakes ◽  
Tuncer Edil ◽  
Morgan Sanger ◽  
Renee Olley ◽  
Tyler Klink

The conventional highway resurfacing technique of mill and overlay (M&O) partially removes the existing pavement and replaces it with asphalt derived from some recycled but mostly virgin materials. Cold-in-place recycling (CIR) is an alternative highway resurfacing method that partially mills the existing pavement and uses it beneath a thinner layer of new asphalt. CIR has become widely used for convenience and cost benefits, but the environmental impacts are poorly quantified. The objective of this study was to quantify the environmental life cycle benefits of using CIR for highway resurfacing instead of M&O. Material quantities and equipment used for CIR and what would have been used in M&O for the same project were provided by contractors for nine highway resurfacing projects in Wisconsin. With this information, a life cycle assessment (LCA) tool was used to determine the relative environmental impacts of the two methods, with energy consumption, water usage, and carbon dioxide emissions chosen as the metrics of the LCA. Results show average environmental savings of 23% in energy consumption and carbon dioxide emissions and 20% in water consumption when using CIR instead of M&O for highway resurfacing. Additionally, CIR reduced virgin aggregate consumption by 37%. Environmental savings achieved by using CIR were found to be directly related to the reduction in volume of new hot mix asphalt (HMA) used, and to the reduction in transportation of materials to and from the site. Linear correlations that can be used to estimate savings of future CIR projects were projected.


2017 ◽  
Vol 98 (6) ◽  
pp. 1227-1229 ◽  
Author(s):  
Angus R. Westgarth-Smith

Ocean acidification (OA) is caused by increasing atmospheric concentrations of carbon dioxide, which dissolves in seawater to produce carbonic acid. This carbonic acid reduces the availability of dissolved aragonite needed for production of some invertebrate exoskeletons with potentially severe consequences for marine calcifier populations. There is a lack of public information on OA with less than 1% of press coverage on OA compared with climate change; OA is not included in UK GCSE and A Level specifications and textbooks; environmental campaigners are much less active in campaigning about OA compared with climate change. As a result of the lack of public awareness OA is rarely discussed in the UK Parliament. Much more public education about OA is needed so that people can respond to the urgent need for technological and lifestyle changes needed to massively reduce carbon dioxide emissions.


Sign in / Sign up

Export Citation Format

Share Document