scholarly journals Application of Composite Pre-Polymerized Coagulants for the Treatment of High-Strength Industrial Wastewaters

Water ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1258 ◽  
Author(s):  
Athanasia K. Tolkou ◽  
Anastasios I. Zouboulis

The aim of this study was the investigation of alternative pre-polymerized coagulants for the treatment of high-strength industrial wastewaters, such as those created by tanneries, or by yeast production industries. The novel inorganic composite coagulant examined in this study (as well as variations of it) was denoted as PSiFAC1.5-10-15. The contribution of a typical polyelectrolyte to improve the effectiveness of the coagulation/flocculation (C/F) process was additionally studied, either by adding it separately (i.e., as a flocculant aid) or by co-polymerizing it within the structure of inorganic coagulant (denoted as PAPEFAC1.5-10-15). It was found that the PSiFAC1.5:10:15 coagulant, either with or without the addition of polyelectrolyte, can provide better efficiency for the C/F process than the conventional coagulants. For example, the addition of 80 mg Al/L in yeast production wastewater samples resulted in a 56% reduction of COD, 40% of turbidity, and 43% of phosphates, regarding the pre-treated anaerobically wastewater samples and reduced by an extra 22%, 14%, and 38% for the pre-treated anaerobically plus aerobically wastewater samples, respectively. The residual aluminum concentration in the treated wastewaters was found to be below the legislation limit of 200 μg Al/L. The characterization of coagulants showed the relatively higher Al13 content of 51% and 43% for the cases of PSiFAC1.5-10-15 and PAPEFAC1.5-10-15, respectively, accompanied by the high zeta-potential measurements (50.5 and 39.5 mV).

2016 ◽  
Vol 182 (2) ◽  
pp. 468-481 ◽  
Author(s):  
Afsin Y. Cetinkaya ◽  
Oguz Kaan Ozdemir ◽  
Ahmet Demir ◽  
Bestami Ozkaya

Author(s):  
Aileen Vandenberg ◽  
Daniel Massucci ◽  
Steven Woltornist ◽  
Douglas Adamson ◽  
Kay Wille
Keyword(s):  

2018 ◽  
Vol 51 (4) ◽  
pp. 46
Author(s):  
N. Venkateswara Rao ◽  
G. Madhusudhan Reddy ◽  
S. Nagarjuna

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1048
Author(s):  
Belén Díaz ◽  
X. Ramón Nóvoa ◽  
Carmen Pérez ◽  
Sheila Silva-Fernández

This research emphasizes the importance of the acid cleaning prior to the phosphate development on high-strength steel rods. It compares the phosphate properties achieved after different acid-pickling conditions. The most common inorganic acids were considered in this study. Additionally, taking into account the environmental and safety concerns of these acids, the assessment of a less harmful organic acid is presented. This study revealed significant differences in the coating morphology and chemical composition whereas no great changes were found in terms of the coating weight or porosity. Thus, hydrochloric and sulfuric acid promote the growth of a Fe-enriched phosphate layer with a less conductive character that is not developed after the pickling with phosphoric acid. The phosphate developed after the citric acid pickling is comparable to that developed after the inorganic acids although with a porosity slightly higher. The temperature of the citric acid bath is an important parameter that affects to the phosphate appearance, composition, and porosity.


HLA ◽  
2021 ◽  
Author(s):  
Maria Loginova ◽  
Olga Makhova ◽  
Daria Smirnova ◽  
Igor Paramonov ◽  
Maksim Zarubin

HLA ◽  
2020 ◽  
Author(s):  
Steve Genebrier ◽  
Vincent Elsermans ◽  
Emeric Texeraud ◽  
Gerald Bertrand ◽  
Virginie Renac

HLA ◽  
2021 ◽  
Author(s):  
Marine Cargou ◽  
Vincent Elsermans ◽  
Isabelle Top ◽  
Laura Blouin ◽  
Jonathan Visentin
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document