scholarly journals THE IMPLEMENTATION OF TURBINE VENTILATOR AS AN ALTERNATIVE POWER PLANT

2020 ◽  
Vol 2 (1) ◽  
pp. 180-185
Author(s):  
Aris Suryadi
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Alternative Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Clean Energy ◽  
Energy Reserves ◽  
Wind Speeds ◽  
Motion Energy ◽  
Alternative Power

Indonesia is actively developing the potential for renewable energy as a substitute for depleting fossil energy reserves. Wind energy is clean energy without polling the environment. Wind energy in Indonesia has great potential, but it is still not optimal enough for its utilization. One form of alternative energy that can be utilized as mechanical energy by wind turbines to convert into electrical energy by dc generators. Ventilators that operate for 24 hours function to suck water and, located on the roof of a warehouse, sports hall . Utilization of wind to become electrical energy is designed from the use of a turbine ventilator as a medium to convert wind into motion energy, where the movement of the turbine is continued by pulley and v-belt comparisons to the generator, this generator produces electricity. This research examines how much electrical energy is produced at different wind speeds ranging from 3 to 5.4 m/s. From the tests conducted, the generator rotation, and the lowest voltage is at wind speed of 3 m/s which is 3.6 V. while the generator speed and the highest voltage is obtained if the wind speed is 5.4 m/s which is 10.3 V.

scholarly journals Pemanfaatan Turbin Ventilator sebagai Pembangkit Listrik Alternatif

2019 ◽  
Vol 4 ◽  
Author(s):  
Aris Suryadi ◽  
Purwandito Tulus Asmoro ◽  
Roja Raihan
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Alternative Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Clean Energy ◽  
Energy Reserves ◽  
Fossil Energy ◽  
Wind Speeds ◽  
Motion Energy

Indonesia is actively developing the potential for renewable energy as a substitute for depleting fossil energy reserves. Wind energy is clean energy without polluting the environment. Wind energy in Indonesia has great potential, but it is still not optimal enough for its utilization. One form of alternative energy that can be utilized as mechanical energy by wind turbines to convert into electrical energy by dc generators. Ventilators that operate for 24 hours function to suck air and, located on the roof of a warehouse, sports hall .. Utilization of wind to become electrical energy, is designed from the use of a ventilator turbine as a medium to convert wind into motion energy, where the movement of the turbine is continued by pulley and v-belt comparisons to the generator, this generator produces electricity. This research examines how much electrical energy is produced at different wind speeds ranging from 3 to 5.4 m/s. From the tests conducted, the generator rotation, and the lowest voltage is at wind speed of 3 m/s which is 3.6 V. while the generator speed and the highest voltage is obtained if the wind speed is 5.4 m/s which is 10.3 V.

Piezoelectric Clamped Beam Energy Harvester Using Vibration Caused by Centrifugal Force at High Wind Speeds

2019 ◽  
Vol 4 (1) ◽  
pp. 41-46 ◽  
Author(s):  
Da Xiao ◽  
Ying Yang ◽  
Qinlong Shen ◽  
Jiamei Jin ◽  
Yiping Wang
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Centrifugal Force ◽  
High Speed ◽  
Energy Harvester ◽  
Structural Parameters ◽  
Electrical Energy ◽  
Open Circuit ◽  
Wind Speeds ◽  
Peak Output Power

Abstract In this study, a piezoelectric wind energy harvester was vibrated that aims to convert high-speed wind energy into electrical energy using vibrations caused by centrifugal force. Vibrations induced by centrifugal force enabled effective distortion of the piezoelectric clamped beam and thus produced electric charge through the piezoelectric effect. A clamped beam was used rather than a conventional thin cantilever to harvest the wind energy in the proposed harvester. The centrifugal force was introduced by a pair of rotating eccentric turbines that are installed on two ball bearings on both sides of the piezoelectric unimorph. Benefiting from the rotating eccentric masses of these turbines, the harvester is capable of capturing wind energy in high speed wind environments. A prototype was set up to examine the effects of the wind speed and the structural parameters on the electrical output of the harvester. It is found that the harvester worked efficiently with wind applied from the axial directions in a 20–55 m/s speed range and produced a maximum open-circuit voltage of 47.2 V. When connected to an external load of 50 kΩ, the harvester showed a peak output power of 3.69 mW at a wind speed of 55 m/s.

scholarly journals SIMULATION BASED DESIGNING OF CONTROL SYSTEMS FOR WIND POWER GENERATION

2020 ◽  
Vol 4 (5) ◽  
pp. 104-109
Author(s):  
Guruswamy Revana ◽  
Amrutha D.E ◽  
Spandana D ◽  
Anusha D
Keyword(s):  
Power Generation ◽  
Wind Speed ◽  
Wind Turbine ◽  
Wind Power ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Clean Energy ◽  
Wind Power Generation ◽  
Induction Generator ◽  
Continuous Power

Wind power is a domestic source of energy, harnessing a limitless local resource and is a potential source of clean electricity generation. Wind is utilized to create electrical energy by means of the kinetic energy formed by air into movement. This energy is changed to electrical energy by wind speed turbines or also called as wind energy exchange systems. Wind speed power generation creates a progressively more significant position in the method the humans power the world. During the process of wind power generation, a variety of characteristics are to be controlled for efficient working of the system and to avoid failure of continuous power supply. In this project we are aiming to control a few such characteristic such as pitch angle, voltage sag and faults that influence wind power generation. The DC link voltage of the Doubly Fed Induction Generator (DFIG) is also monitored. In this wind turbine system consists of wind turbine, AC generator and controllers are considered. The major purpose of the paper is to find out the mathematical model of the wind turbine, authenticate it by simulation, and devise a suitable controller to present a common aim of outlook regarding the use of this type of clean energy production. Various rudiments are connected collectively and the complete arrangement is modelled and also simulated. The simulation results verify the accuracy of the mathematical models developed and can be utilized for a improved design of systems. Wind turbines make use DFIG which consists of wound rotor type induction generator and a PWM converter of IGBT bases of AC/DC/AC. The stator winding is connected directly to the 60 Hz grid while the rotor is fed at variable frequency through the AC/DC/AC converter. The DFIG machinery permits pulling out highest energy from the wind from lowest wind speeds and optimizing the speed of the turbine there by decreasing mechanical stresses on the turbine during gusts of wind. The most favourable turbine speed producing increased mechanical energy for a given speed of the wind which is directly proportional to the wind speed. The other merit of the DFIG expertise is the capability for the converters of power electronics to produce or take in reactive power, thereby reducing the need for putting in capacitor banks as done for the generators of squirrel-cage induction motor type.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

Creating the Wind Energy for Operating the 3-C-Section Blades Wind Car

2012 ◽  
Vol 622-623 ◽  
pp. 1188-1193 ◽  
Author(s):  
Hüseyin Çamur ◽  
Youssef Kassem
Keyword(s):  
Wind Speed ◽  
Angular Velocity ◽  
Wind Energy ◽  
Drag Force ◽  
Mechanical Energy ◽  
Main Shaft ◽  
Airflow Velocity ◽  
Low Speed ◽  
Low Wind Speed

The purpose of this work is to determine the drag characteristics and the torque of three C-section blades wind car. Three C-section blades are directly connected to wheels by using of various kinds of links. Gears are used to convert the wind energy to mechanical energy to overcome the load exercised on the main shaft under low speed. Previous work on three vertical blades wind car resulted in discrepancies when compared to this work. Investigating these differences was the motivation for this series of work. The calculated values were compared to the data of three vertical blades wind car. The work was conducted in a low wind speed. The drag force acting on each model was calculated with an airflow velocity of 4 m/s and angular velocity of the blade of 13.056 rad/s.

Hydrogen Storage in Magnesium-Based Alloys

MRS Bulletin ◽  
1999 ◽  
Vol 24 (11) ◽  
pp. 40-44 ◽  
Author(s):  
R.B. Schwarz
Keyword(s):  
Energy Density ◽  
Hydrogen Storage ◽  
Alternative Energy ◽  
Distribution Systems ◽  
Electrical Energy ◽  
Clean Energy ◽  
Energy System ◽  
Liquid Hydrogen ◽  
Rechargeable Batteries ◽  
Oil Crisis

Magnesium can reversibly store about 7.7 wt% hydrogen, equivalent to more than twice the density of liquid hydrogen. This high storage capacity, coupled with a low price, suggests that magnesium and magnesium alloys could be advantageous for use in battery electrodes and gaseous-hydrogen storage systems. The use of a hydrogen-storage medium based on magnesium, combined with a fuel cell to convert the hydrogen into electrical energy, is an attractive proposition for a clean transportation system. However, the advent of such a system will require further research into magnesium-based alloys that form less stable hydrides and proton-conducting membranes that can raise the operating temperature of the current fuel cells.Following the U.S. oil crisis of 1974, research into alternative energy-storage and distribution systems was vigorously pursued. The controlled oxidation of hydrogen to form water was proposed as a clean energy system, creating a need for light and safe hydrogen-storage media. Extensive research was done on inter-metallic alloys, which can store hydrogen at densities of about 1500 cm3-H2 gas/ cm3-hydride, higher than the storage density achieved in liquid hydrogen (784 cm3/cm3 at –273°C) or in pressure tanks (˜200 cm3/cm3 at 200 atm). The interest in metal hydrides accelerated following the development of portable electronic devices (video cameras, cellular phones, laptop computers, tools, etc.), which created a consumer market for compact, rechargeable batteries. Initially, nickel-cadmium batteries fulfilled this need, but their relatively low energy density and the toxicity of cadmium helped to drive the development of higher-energy-density, less toxic, rechargeable batteries.

scholarly journals Improving Lidar-Derived Turbulence Estimates for Wind Energy

2016 ◽  
Author(s):  
Jennifer F. Newman ◽  
Andrew Clifton
Keyword(s):  
Machine Learning ◽  
Wind Speed ◽  
Wind Energy ◽  
Sonic Anemometer ◽  
Turbulence Models ◽  
Volume Averaging ◽  
Turbine Rotor ◽  
Error Reduction ◽  
Power Prediction ◽  
Wind Speeds

Abstract. Remote sensing devices such as lidars are currently being investigated as alternatives to cup anemometers on meteorological towers. Although lidars can measure mean wind speeds at heights spanning an entire turbine rotor disk and can be easily moved from one location to another, they measure different values of turbulence than an instrument on a tower. Current methods for improving lidar turbulence estimates include the use of analytical turbulence models and expensive scanning lidars. While these methods provide accurate results in a research setting, they cannot be easily applied to smaller, commercially available lidars in locations where high-resolution sonic anemometer data are not available. Thus, there is clearly a need for a turbulence error reduction model that is simpler and more easily applicable to lidars that are used in the wind energy industry. In this work, a new turbulence error reduction algorithm for lidars is described. The algorithm, L-TERRA, can be applied using only data from a stand-alone commercially available lidar and requires minimal training with meteorological tower data. The basis of L-TERRA is a series of corrections that are applied to the lidar data to mitigate errors from instrument noise, volume averaging, and variance contamination. These corrections are applied in conjunction with a trained machine-learning model to improve turbulence estimates from a vertically profiling WINDCUBE v2 lidar. L-TERRA was tested on data from three sites – two in flat terrain and one in semicomplex terrain. L-TERRA significantly reduced errors in lidar turbulence at all three sites, even when the machine-learning portion of the model was trained on one site and applied to a different site. Errors in turbulence were then related to errors in power through the use of a power prediction model for a simulated 1.5 MW turbine. L-TERRA also reduced errors in power significantly at all three sites, although moderate power errors remained for periods when the mean wind speed was close to the rated wind speed of the turbine and periods when variance contamination had a large effect on the lidar turbulence error. Future work will include the use of a lidar simulator to better understand how different factors affect lidar turbulence error and to determine how these errors can be reduced using information from a stand-alone lidar.

Effect of Slotted Angle on Savonius Wind Turbine Performance

2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Electrical Energy ◽  
Speed Ratio ◽  
Angle Variation ◽  
Wind Speeds ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.

scholarly journals Test campaign of a ducted wind turbine in real operating conditions

2019 ◽  
Vol 113 ◽  
pp. 03005
Author(s):  
Enrico Valditerra ◽  
Massimo Rivarolo ◽  
Aristide F. Massardo ◽  
Marco Gualco
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Energy Production ◽  
Electrical Energy ◽  
Clean Energy ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Ambient Conditions ◽  
Wind Speeds ◽  
Electrical Energy Production

Wind turbine installation worldwide has increased at unrested pace, as it represents a 100% clean energy with zero CO2 and pollutant emissions. However, visual and acoustic impact of wind turbines is still a drawback, in particular in urban areas. This paper focuses on the performance evaluation of an innovative horizontal axis ducted wind turbine, installed in the harbour of Genova (Italy) in 2018: the turbine was designed in order to minimize visual and acoustic impacts and maximize electrical energy production, also during low wind speed periods. The preliminary study and experimental analyses, performed by the authors in a previous study, showed promising results in terms of energy production, compared to a traditional generator ( factor >2.5 on power output). In the present paper, the test campaign on a scaled-up prototype, installed in the urban area of Genova, is performed, with a twofold objective: (i) comparison of the ducted innovative turbine with a standard one, in order to verify the increase in energy production; (ii) analysis of the innovative turbine for different wind speeds and directions, evaluating the influence of ambient conditions on performance. Finally, based on the obtained results, an improved setup is proposed for the ducted wind turbine, in order to further increase energy production mitigating its visual impact.

scholarly journals Hollow Piezoelectric Ceramic Fibers for Energy Harvesting Fabrics

2013 ◽  
Vol 8 (1) ◽  
pp. 155892501300800
Author(s):  
François M. Guillot ◽  
Haskell W. Beckham ◽  
Johannes Leisen
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Mechanical Energy ◽  
Electrical Power ◽  
Electrical Energy ◽  
Lead Zirconate ◽  
Ceramic Fibers ◽  
Power Sources ◽  
Electromechanical Performance ◽  
Alternative Power

In the past few years, the growing need for alternative power sources has generated considerable interest in the field of energy harvesting. A particularly exciting possibility within that field is the development of fabrics capable of harnessing mechanical energy and delivering electrical power to sensors and wearable devices. This study presents an evaluation of the electromechanical performance of hollow lead zirconate titanate (PZT) fibers as the basis for the construction of such fabrics. The fibers feature individual polymer claddings surrounding electrodes directly deposited onto both inside and outside ceramic surfaces. This configuration optimizes the amount of electrical energy available by placing the electrodes in direct contact with the surface of the material and by maximizing the active piezoelectric volume. Hollow fibers were electroded, encapsulated in a polymer cladding, poled and characterized in terms of their electromechanical properties. They were then glued to a vibrating cantilever beam equipped with a strain gauge, and their energy harvesting performance was measured. It was found that the fibers generated twice as much energy density as commercial state-of-the-art flexible composite sensors. Finally, the influence of the polymer cladding on the strain transmission to the fiber was evaluated. These fibers have the potential to be woven into fabrics that could harvest mechanical energy from the environment and could eventually be integrated into clothing.

Sign in / Sign up

Export Citation Format

Share Document