scholarly journals Effect of Confining Pressures on Dynamic Response Characteristics of Silty Soils in the Niger Delta

Author(s):  
J. O. Okovido ◽  
C. Kennedy

The probability of earthquake occurrence in the Niger Delta region of Nigeria was studied in this research. The resonant column/bender element tests were used for the study. Series of analysis were carried out on compacted silt in subsoil strata obtained from various locations in Rivers, Bayelsa, Delta and Akwa Ibom States. The effects of confinement on frequency, shear modulus, shear velocity and damping ratio were studied. The tests results revealed that confinement has effects on the investigated parameters. Thus, frequency response increases with increase in confinement pressure. Also, the resonance column test at various confinements revealed changes in shear modulus, accelerometer output and damping ratio. Accordingly, there was high disparity in the tested parameters as confinement pressure was increased. Similarly, the bender element tests also showed that pressure has effect on shear wave-velocity, shear modulus and damping ratio confinement. The shear modulus and shear wave-velocity generally increased as confinement pressure was increased, while damping ratio decreases as confinement pressure was increased. The variations in Resonance Column/Bender Element test parameters showed that the silty soil in the Niger Delta region, an oil and gas rich area, is likely to experience earthquake in the future. Therefore, geological data should be collated for monitoring, especially as several geological activities take place in the region.

Author(s):  
J. O. Okovido ◽  
C. Kennedy

The study investigated the earthquake potential in Niger Delta region of Nigeria. A series of resonant column and bender element test was performed on compacted clay soil samples across the investigated Niger Delta States, which showed the influence of confinement on frequency, shear modulus, shear velocity and damping ratio. The confinement in clay was high. The frequency response increases with pressure increase. Also, the resonance column test at various confinements revealed changes in shear modulus, accelerometer output and damping ratio. Thus, there was high variation in the test parameters as confinement pressure was increased. Similarly, the bender element tests also showed that pressure has effect on shear wave-velocity, shear modulus and damping ratio confinement. Although, unlike Resonance Column tests, the shear modulus and shear wave-velocity generally increased as confinement pressure was increased, while for damping ratio it decreases as confinement pressure was increased. The variations in resonance column/binder element test parameters showed that the Niger Delta region, as an oil and gas area, is susceptible to earthquake. Therefore, continuous monitoring of oil exploration activities must be put in place.


Author(s):  
J.O. Okovido ◽  
C. Kennedy

The study investigated the dynamic soil properties of States in Niger Delta region of Nigeria as a function of seismic activities. The down-hole seismic test was used to determine the response of the soils. The results of soil samples collected up to 30m depth, showed that the average young modulus increases with increase in depth, which ranged from 115.77±1.74 to 3231.17±1.01 kPa across the States. Also, shear wave velocity generally increases with increase in depth. The average shear wave velocity across the States ranged from 126.00±1.86 to 288.00±2.63m/s. Also, the average P-wave velocity increases with depth, with values across the States ranging from 310.60±3.51 to 656.00±3.69m/s. On the other hand, the void ratio was observed to be constant at certain range of depth, and in most with values across the States ranging from 0.651±.093 to 0.860±.067. Unlike void ratio, Poisson’s ratio fluctuates with depth, with values across the States ranging from 0.23±2.27 to 0.36±1.18. Based on the results, the Niger Delta region may be resistant to earthquake, but as an oil hub of Nigeria, it is also susceptible to earthquake that could be triggered by stress due to heavy load and seismic activities.


2019 ◽  
Vol 92 ◽  
pp. 04002
Author(s):  
Litong Ji ◽  
Abraham C.F. Chiu ◽  
Lu Ma ◽  
Chao Jian

This article presents a laboratory study on the maximum shear modulus of a THF hydrate bearing calcareous sand (CS)–fines mixture. The maximum shear modulus was inferred from the shear wave velocity measured from the bender elements installed in a temperature-controlled triaxial apparatus. The specimen preparation procedures were specially designed to mimic the hydrate formation inside the internal pores of CS. A trial test was conducted to validate whether the shear wave velocity is a feasible parameter to monitor the formation and dissociation of hydrate in the CS-fines mixture. Based on the bender element test results, hydrate has a more profound effect than confining pressure on enhancing the maximum shear modulus of CS-fines mixture.


2000 ◽  
Vol 37 (3) ◽  
pp. 638-651 ◽  
Author(s):  
Shang-Yuh Lin ◽  
Ping Sien Lin ◽  
Hong-Su Luo ◽  
C Hsein Juang

In this paper, the results of an experimental investigation of dynamic characteristics of gravelly cobble deposits, such as shear modulus (G) and damping ratio (D), are presented. The gravelly cobble deposits are very common in the Taichung metropolitan area of Taiwan where there is an urgent need to determine G and D for dynamic analysis and design of structures. The test program includes measurements of shear wave velocity by the downhole method and large-scale dynamic triaxial tests and resonant-column tests. Special consideration is given to preparing samples of gravelly cobble deposits for laboratory tests. The "equal-weight replacement method" to scale down the real gravelly deposits to cell diameters is used for the preparation of samples. This method is found to be satisfactory, as consistent and reasonable results are obtained. The results of the present study show that the shear modulus - shear strain (G-γ) relationship for this gravelly deposit does not follow exactly those reported in the literature. The deviation of this G-γ relationship from those reported in the literature is investigated and explained.Key words: shear modulus, damping ratio, downhole, shear wave velocity, gravel.


Author(s):  
Muhammad Irfan ◽  
Giovanni Cascante ◽  
Dipanjan Basu ◽  
Denis LeBoeuf

The low-strain dynamic behavior of Leda clays is investigated using the resonant column (RC) and bender element (BE) tests. Four undisturbed, lightly overconsolidated Leda clay samples, collected from two sites near the St-Lawrence River valley, are tested at different strains, confining stresses, and frequencies. To evaluate the effect of excitation frequency, simultaneous measurements of shear wave velocity using RC and BE tests are performed. The results show that the samples from the different sites behave differently. The high sensitivity of the Leda clays does not have a significant effect on the modulus degradation curves. However, the measured degradation curves are similar to those of soft clays with high plasticity, which is contrary to the expected behaviour of these low plasticity (Ip = 6.2-20) specimens. Likewise, the measured damping ratios are on the lower end of the typical values reported for soils of high plasticity. Low values of damping ratio make the amplification of small seismic events more likely in Leda clay deposits. The difference in the shear wave velocity measurements from RC and BE tests ranges from 17% to 26% depending on the confinement, likely because of the strong influence of P-waves observed in the BE tests for these soils.


2019 ◽  
Vol 37 (3) ◽  
pp. 263
Author(s):  
Breno Padovezi Rocha ◽  
Heraldo Luiz Giacheti

ABSTRACT. The shear wave velocity (Vs) is an important geotechnical parameter to be used in dynamic problems (e.g. earthquakes and vibration problems) as well as in static deformation analysis such as excavations and foundation engineering design. There are several in situ seismic tests to determine Vs such as the crosshole and the downhole techniques, as well as hybrid tests (e.g. seismic dilatometer – SDMT). This paper presents crosshole, downhole and SDMT tests carried out in a typical tropical soil profile from Brazil. Advantages and limitations regarding the test procedures and interpretation are briefly presented and differences observed among Vs determined by these techniques are discussed. Shear wave velocities (Vs) estimated from the crosshole, downhole and SDMT tests ranging from 194 to 370 m/s. The shear wave velocity suggests that the experimental site could be divided into two strata, which are in agreement with soil profile description. The maximum shear modulus (G0) calculated from the Vs by theory of elasticity can be used to show the investigated tropical soil is a typical unusual geomaterial. This article also emphasizes that the SDMT is a useful test for site investigation since it allows a great means for profiling geostratigraphy and soil engineering properties during routine site investigation as well as for dynamics problems. Keywords: shear wave velocity, maximum shear modulus, crosshole, downhole, SDMT.RESUMO. A velocidade de onda cisalhante (Vs) é um parâmetro geotécnico empregado em análises dinâmicas (terremotos e problemas de vibração), bem como em análises estáticas (escavações e projeto de fundações). Existem vários ensaios sísmicos de campo para a determinação de Vs, entre eles as técnicas crosshole e downhole, e os ensaios híbridos (por exemplo, dilatômetro sísmico – SDMT). Este artigo apresenta os ensaios crosshole, downhole e SDMT realizados em um perfil típico de solo tropical do Brasil, as vantagens e limitações dos procedimentos de ensaio e de interpretação são brevemente apresentadas, e as diferenças observadas entre os valores de Vs determinados pelas diferentes técnicas são discutidas. Os perfis de Vs determinados pelas diferentes técnicas variaram de 194 a 370 m/s. A velocidade da onda cisalhante sugere que o campo experimental investigado pode ser dividido em dois horizontes, os quais estão de acordo com a descrição do perfil do solo estudado. O módulo de cisalhamento máximo (G0), calculado a partir de Vs pela teoria da elasticidade, pode ser utilizado para demonstrar o comportamento não convencional do solo investigado. Este artigo também enfatiza que o SDMT é um ensaio geotécnico útil para a investigação geotécnica do subsolo, uma vez que permite a definição do perfil estratigráfico e a estimativa de parâmetros estáticos e dinâmicos de um projeto.Palavras-chave: velocidade de onda cisalhante, módulo de cisalhamento máximo, crosshole, downhole, SDMT.


2021 ◽  
Author(s):  
Yu Chen

<p>In order to study the effect of the different consolidation pressure, loading-unloading path and gravel content on the shear modulus of the small strain of sliding zone soil, a set of consolidation bender element test device was developed. The device consists of three parts: a consolidation system, a deformation measuring system, and a shear wave testing system. The consolidation system is composed of a traditional consolidation instrument and the plexiglass cylinder box. The sample is cylindrical in shape and has a size of 50 mm×50 mm. The consolidation displacement is measured by a digital display micrometer. Shear wave testing system is a wave velocity measurement system made of piezoelectric ceramic. The experimental results show that the device can control the consolidation pressure and measure the vertical deformation, measure the shear wave velocity of the sliding zone soil in real-time, and then study the variation rule of the small strain shear modulus of the sliding zone soil with gravels. The shear modulus of the sliding zone soil increases with an increase in the consolidation pressure. The shear modulus of the unloading of sliding zone soil is larger than that of loading. Under the loading pressure of 200 kPa and 400 kPa, the shear modulus of the sliding zone soil first decreases and then increases with an increase in the gravel content. In the process of unloading, the shear modulus of the sliding zone soil increases with an increase in the gravel content. </p>


2008 ◽  
Vol 45 (10) ◽  
pp. 1426-1438 ◽  
Author(s):  
Jun-Ung Youn ◽  
Yun-Wook Choo ◽  
Dong-Soo Kim

The bender element method is an experimental technique used to determine the small-strain shear modulus (Gmax) of a soil by measuring the velocity of shear wave propagation through a sample. Bender elements have been applied as versatile transducers to measure the Gmax of wet and dry soils in various laboratory apparatuses. However, certain aspects of the bender element method have yet to be clearly specified because of uncertainties in determining travel time. In this paper, the bender element (BE), resonant column (RC), and torsional shear (TS) tests were performed on the same specimens using the modified Stokoe-type RC and TS testing equipment. Two clean sands, Toyoura and silica sands, were tested at various densities and mean effective stresses under dry and saturated conditions. Based on the test results, methods of determining travel time in BE tests were evaluated by comparing the results of RC, TS, and BE tests. Also, methods to evaluate Gmax of saturated sands from the shear-wave velocity (Vs) obtained by RC and BE tests were investigated by comparing the three sets of test results. Biot’s theory on frequency dependence of shear-wave velocity was adopted to consider dispersion of a shear wave in saturated conditions. The results of this study suggest that the total mass density, which is commonly used to convert Gmax from the measured Vs in saturated soils, should not be used to convert Vs to Gmax when the frequency of excitation is 10% greater than the characteristic frequency (fc) of the soil.


2016 ◽  
Vol 39 (4) ◽  
pp. 20140197 ◽  
Author(s):  
M. Finas ◽  
H. Ali ◽  
G. Cascante ◽  
P. Vanheeghe

Geophysics ◽  
2009 ◽  
Vol 74 (3) ◽  
pp. E135-E147 ◽  
Author(s):  
Gregor T. Baechle ◽  
Gregor P. Eberli ◽  
Ralf J. Weger ◽  
Jose Luis Massaferro

To assess saturation effects on acoustic properties in carbonates, we measure ultrasonic velocity on 38 limestone samples whose porosity ranges from 5% to 30% under dry and water-saturated conditions. Complete saturation of the pore space with water causes an increase and decrease in compressional- and shear-wave velocity as well as significant changes in the shear moduli. Compressional velocities of most water-saturated samples are up to [Formula: see text] higher than the velocities of the dry samples. Some show no change, and a few even show a decrease in velocity. Shear-wave velocity [Formula: see text] generally decreases, but nine samples show an increase of up to [Formula: see text]. Water saturation decreases the shear modulus by up to [Formula: see text] in some samples and increases it by up to [Formula: see text] in others. The average increase in the shear modulus with water saturation is [Formula: see text]; the average decrease is [Formula: see text]. The [Formula: see text] ratio shows an overall increase with water saturation. In particular, rocks displaying shear weakening have distinctly higher [Formula: see text] ratios. Grainstone samples with high amounts of microporosity and interparticle macro-pores preferentially show shear weakening, whereas recrystallized limestones are prone to increase shear strengths with water saturation. The observed shear weakening indicates that a rock-fluid interaction occurs with water saturation, which violates one of the assumptions in Gassmann’s theory. We find a positive correlation between changes in shear modulus and the inability of Gassmann’s theory to predict velocities of water-saturated samples at high frequencies. Velocities of water-saturated samples predicted by Gassmann’s equation often exceed measured values by as much as [Formula: see text] for samples exhibiting shear weakening. In samples showing shear strengthening, Gassmann-predicted velocity values are as much as [Formula: see text] lower than measured values. In 66% of samples, Gassmann-predicted velocities show a misfit to measured water-saturated P-wave velocities. This discrepancy between measured and Gassmann-predicted velocity is not caused solely by velocity dispersion but also by rock-fluid interaction related to the pore structure of carbonates. Thus, a pore analysis should be conducted to assess shear-moduli changes and the resultant uncertainty for amplitude variation with offset analyses and velocity prediction using Gassmann’s theory.


Sign in / Sign up

Export Citation Format

Share Document