scholarly journals Amorphous Ni x Co y P-supported TiO2 nanotube arrays as an efficient hydrogen evolution reaction electrocatalyst in acidic solution

2019 ◽  
Vol 10 ◽  
pp. 62-70 ◽  
Author(s):  
Yong Li ◽  
Peng Yang ◽  
Bin Wang ◽  
Zhongqing Liu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Hydrogen Evolution ◽  
Hydrogen Evolution Reaction ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Nanotube Arrays ◽  
Active Surface Area ◽  
X Ray ◽  
Transmission Electron

Bimetallic phosphides have been attracting increasing attention due to their synergistic effect for improving the hydrogen evolution reaction as compared to monometallic phosphides. In this work, NiCoP modified hybrid electrodes were fabricated by a one-step electrodeposition process with TiO2 nanotube arrays (TNAs) as a carrier. X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy and scanning transmission electron microscopy/energy-dispersive X-ray spectroscopy were used to characterize the physiochemical properties of the samples. The electrochemical performance was investigated by cyclic voltammetry, linear sweep voltammetry, and electrochemical impedance spectroscopy. We show that after incorporating Co into Ni–P, the resulting Ni x Co y P/TNAs present enhanced electrocatalytic activity due to the improved electron transfer and increased electrochemically active surface area (ECSA). In 0.5 mol L−1 H2SO4 electrolyte, the Ni x Co y P/TNAs (x = 3.84, y = 0.78) demonstrated an ECSA value of 52.1 mF cm−2, which is 3.8 times that of Ni–P/TNAs (13.7 mF cm−2). In a two-electrode system with a Pt sheet as the anode, the Ni x Co y P/TNAs presented a bath voltage of 1.92 V at 100 mA cm−2, which is an improvment of 79% over that of 1.07 V at 10 mA cm−2.

scholarly journals Fabrication, characterization and photocatalytic properties of CdS nanoparticles modified by N-doped TiO2 NTs

2018 ◽  
Vol 36 (3) ◽  
pp. 348-353
Author(s):  
Dawei Gao ◽  
Chunxia Wang ◽  
Yu Jian ◽  
Weiwei Li ◽  
Pengyu Dong
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Emission Spectra ◽  
Photocatalytic Properties ◽  
Cds Nanoparticles ◽  
Nanotube Arrays ◽  
X Ray ◽  
Transmission Electron

AbstractHighly ordered TiO2 nanotube arrays (TiO2 NTs) were prepared by anodic oxidizing method on a surface of Ti substrate. Fabrication of nitrogen-doped TiO2 nanotube arrays (N-TiO2 NTs) was carried out by immersion in ammonia solution. CdS nanoparticles loaded N-doped TiO2 nanotube arrays (CdS/N-TiO2 NTs) were obtained by successive ionic layer adsorption and reaction (SILAR) technique. The samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), photoluminescence (PL) emission spectra and ultraviolet-visible (UV-Vis) diffuse reflectance spectroscopy (DRS). The results indicate that the TiO2 nanotube diameter and wall thickness are 100 nm to 120 nm and 20 nm to 30 nm, respectively. Moreover, the morphology and structure of the highly ordered TiO2 NTs are not affected by N-doping. Furthermore, CdS nanoparticles are evenly distributed on the surface of TiO2 NTs. Finally, the photocatalytic activity of CdS/N-TiO2 NTs was evaluated by degradation of MO under visible-light irradiation. Compared with TiO2 NTs, N-TiO2 NTs, CdS/N-TiO2 NTs exhibited enhanced photocatalytic properties, and the highest degradation rate of CdS/N-TiO2NTs could reach 97.6 % after 90 min of irradiation.

scholarly journals 3D Modeling of Silver Doped ZrO2 Coupled Graphene-Based Mesoporous Silica Quaternary Nanocomposite for a Nonenzymatic Glucose Sensing Effects

Nanomaterials ◽  
2022 ◽  
Vol 12 (2) ◽  
pp. 193
Author(s):  
Kamrun Nahar Fatema ◽  
Chang-Sung Lim ◽  
Yin Liu ◽  
Kwang-Youn Cho ◽  
Chong-Hun Jung ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Mesoporous Silica ◽  
Photoelectron Spectroscopy ◽  
Glucose Sensor ◽  
Diffuse Reflectance Spectroscopy ◽  
Active Material ◽  
Glucose Sensing ◽  
X Ray ◽  
Transmission Electron

We described the novel nanocomposite of silver doped ZrO2 combined graphene-based mesoporous silica (ZrO2-Ag-G-SiO2,) in bases of low-cost and self-assembly strategy. Synthesized ZrO2-Ag-G-SiO2 were characterized through X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDX), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Raman spectroscopy, Nitrogen adsorption-desorption isotherms, X-ray photoelectron spectroscopy (XPS), and Diffuse Reflectance Spectroscopy (DRS). The ZrO2-Ag-G-SiO2 as an enzyme-free glucose sensor active material toward coordinate electro-oxidation of glucose was considered through cyclic voltammetry in significant electrolytes, such as phosphate buffer (PBS) at pH 7.4 and commercial urine. Utilizing ZrO2-Ag-G-SiO2, glucose detecting may well be finished with effective electrocatalytic performance toward organically important concentrations with the current reaction of 9.0 × 10−3 mAcm−2 and 0.05 mmol/L at the lowest potential of +0.2 V, thus fulfilling the elemental prerequisites for glucose detecting within the urine. Likewise, the ZrO2-Ag-G-SiO2 electrode can be worked for glucose detecting within the interferometer substances (e.g., ascorbic corrosive, lactose, fructose, and starch) in urine at proper pH conditions. Our results highlight the potential usages for qualitative and quantitative electrochemical investigation of glucose through the ZrO2-Ag-G-SiO2 sensor for glucose detecting within the urine concentration.

scholarly journals Synthesis of nickel/gallium nanoalloys using a dual-source approach in 1-alkyl-3-methylimidazole ionic liquids

2019 ◽  
Vol 10 ◽  
pp. 1754-1767
Author(s):  
Ilka Simon ◽  
Julius Hornung ◽  
Juri Barthel ◽  
Jörg Thomas ◽  
Maik Finze ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Dark Field ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Annular Dark Field ◽  
Dual Source ◽  
Induced Decomposition

NiGa is a catalyst for the semihydrogenation of alkynes. Here we show the influence of different dispersion times before microwave-induced decomposition of the precursors on the phase purity, as well as the influence of the time of microwave-induced decomposition on the crystallinity of the NiGa nanoparticles. Microwave-induced co-decomposition of all-hydrocarbon precursors [Ni(COD)2] (COD = 1,5-cyclooctadiene) and GaCp* (Cp* = pentamethylcyclopentadienyl) in the ionic liquid [BMIm][NTf2] selectively yields small intermetallic Ni/Ga nanocrystals of 5 ± 1 nm as derived from transmission electron microscopy (TEM) and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and supported by energy-dispersive X-ray spectrometry (EDX), selected-area energy diffraction (SAED) and X-ray photoelectron spectroscopy (XPS). NiGa@[BMIm][NTf2] catalyze the semihydrogenation of 4-octyne to 4-octene with 100% selectivity towards (E)-4-octene over five runs, but with poor conversion values. IL-free, precipitated NiGa nanoparticles achieve conversion values of over 90% and selectivity of 100% towards alkene over three runs.

Hydrothermal Synthesis of Few-Layer and Edge-Rich Cobalt-Doped Molybdenum Selenide/Nitrogenated Graphene Composite and Investigation of Its Electrocatalytic Activity for Hydrogen Evolution Reaction

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650107 ◽  
Author(s):  
Ming Ou ◽  
Lin Ma ◽  
Limei Xu ◽  
Zhuomei Yang ◽  
Haizhen Li
Keyword(s):  
Electron Microscopy ◽  
Hydrogen Evolution ◽  
Hydrogen Evolution Reaction ◽  
Photoelectron Spectroscopy ◽  
Hydrothermal Route ◽  
X Ray ◽  
Graphene Composite ◽  
Molybdenum Selenide ◽  
Nitrogen Doped Graphene ◽  
Doped Graphene

Cobalt-doped MoSe2/nitrogenated graphene composite has been successfully synthesized via a facile hydrothermal route and is investigated as an electrocatalyst for hydrogen evolution reaction (HER). The as-prepared samples are well characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and Raman spectrum. The results reveal that Co-doped MoSe2 nanosheets which are characteristic of few layers (2–4 layers) and abundant exposed active edge sites are well anchored on the nitrogen-doped graphene sheets to constitute robust composites. When evaluated as catalysts for HER, the obtained composites demonstrate superior electrocatalytic activities toward HER.

Limitations to the use of Sb as a Surfactant During SiGe MBE

1998 ◽  
Vol 533 ◽  
Author(s):  
Glenn G. Jernigan ◽  
Conrad L. Silvestre ◽  
Mohammad Fatemi ◽  
Mark E. Twigg ◽  
Phillip E. Thompson
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Quantum Well ◽  
Photoelectron Spectroscopy ◽  
Surface Coverage ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Alloy Concentration

AbstractThe use of Sb as a surfactant in suppressing Ge segregation during SiGe alloy growth was investigated as a function of Sb surface coverage, Ge alloy concentration, and alloy thickness using xray photoelectron spectroscopy, x-ray diffraction, and transmission electron microscopy. Unlike previous studies where Sb was found to completely quench Ge segregation into a Si capping layer, we find that Sb can not completely prevent Ge segregation while Si and Ge are being co-deposited. This results in the production of a non-square quantum well with missing Ge at the beginning and extra Ge at the end of the alloy. We also found that Sb does not relieve strain in thin films but does result in compositional or strain variations within thick alloy layers.

scholarly journals Biosynthesized Highly Stable Au/C Nanodots: Ideal Probes for the Selective and Sensitive Detection of Hg2+ Ions

Nanomaterials ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 245 ◽  
Author(s):  
Sada Venkateswarlu ◽  
Saravanan Govindaraju ◽  
Roopkumar Sangubotla ◽  
Jongsung Kim ◽  
Min-Ho Lee ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Metal Ions ◽  
Fluorescent Probe ◽  
Photoelectron Spectroscopy ◽  
Industrial Development ◽  
Carbon Nanodots ◽  
Detection Mechanism ◽  
X Ray ◽  
Transmission Electron

The enormous ongoing industrial development has caused serious water pollution which has become a major crisis, particularly in developing countries. Among the various water pollutants, non-biodegradable heavy metal ions are the most prevalent. Thus, trace-level detection of these metal ions using a simple technique is essential. To address this issue, we have developed a fluorescent probe of Au/C nanodots (GCNDs-gold carbon nanodots) using an eco-friendly method based on an extract from waste onion leaves (Allium cepa-red onions). The leaves are rich in many flavonoids, playing a vital role in the formation of GCNDs. Transmission electron microscopy (TEM) and Scanning transmission electron microscopy-Energy-dispersive X-ray spectroscopy (STEM-EDS) elemental mapping clearly indicated that the newly synthesized materials are approximately 2 nm in size. The resulting GCNDs exhibited a strong orange fluorescence with excitation at 380 nm and emission at 610 nm. The GCNDs were applied as a fluorescent probe for the detection of Hg2+ ions. They can detect ultra-trace concentrations of Hg2+ with a detection limit of 1.3 nM. The X-ray photoelectron spectroscopy results facilitated the identification of a clear detection mechanism. We also used the new probe on a real river water sample. The newly developed sensor is highly stable with a strong fluorescent property and can be used for various applications such as in catalysis and biomedicine.

scholarly journals Fabrication of Hybrid Catalyst ZnO Nanorod/α-Fe2O3 Composites for Hydrogen Evolution Reaction

Crystals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 356
Author(s):  
Kasimayan Uma ◽  
Elavarasan Muniranthinam ◽  
Siewhui Chong ◽  
Thomas C.-K Yang ◽  
Ja-Hon Lin
Keyword(s):  
Hydrogen Evolution ◽  
Hydrogen Evolution Reaction ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Nickel Foam ◽  
Zno Nanorods ◽  
Synergetic Effect ◽  
Zno Nanorod ◽  
Fe2o3 Nanoparticles ◽  
X Ray

This report presents the synthesis of ZnO nanorod/α-Fe2O3 composites by the hydrothermal method with different weight percentages of α-Fe2O3 nanoparticles. The as-synthesized nanorod composites were characterized by different techniques, such as X-ray diffraction (XRD), Fourier transform-infrared (FT-IR), field emission scanning electron microscopy (FE-SEM), electrochemical impedance spectroscopy (EIS), and X-ray photoelectron spectroscopy (XPS). From our results, it was found that the ZnO/α-Fe2O3 (3 wt%) nanorod composites exhibit a higher hydrogen evolution reaction (HER) activity when compared to other composites. The synergetic effect between ZnO and (3 wt%) of α-Fe2O3 nanocomposites resulted in a low onset potential of −125 mV, which can effectively produce more H2 than pure ZnO. The H2 production rate over the composite of ZnO/α-Fe2O3 (3 wt%) clearly shows a significant improvement in the photocatalytic activity in the heterojunction of the ZnO nanorods and α-Fe2O3 nanoparticles on nickel foam.

scholarly journals Heterogeneous Fenton-like oxidation of p-hydroxybenzoic acid using Fe/CeO2-TiO2 catalyst

2019 ◽  
Vol 79 (7) ◽  
pp. 1276-1286 ◽  
Author(s):  
Tijani Hammedi ◽  
Mohamed Triki ◽  
Mayra G. Alvarez ◽  
Jordi Llorca ◽  
Abdelhamid Ghorbel ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Molar Ratio ◽  
Hydroxybenzoic Acid ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Temperature Programmed

Abstract This paper is built on the Fenton-like oxidation of p-hydroxybenzoic acid (p–HBZ) in the presence of H2O2 and 3%Fe supported on CeO2-TiO2 aerogels under mild conditions. These catalysts were deeply characterized by X-ray diffraction (XRD), hydrogen temperature programmed reduction (H2-TPR), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and X-ray photoelectron spectroscopy (XPS). The effect of thermal treatment, pH (2–3, 5, 7), H2O2/p–HBZ molar ratio (5, 15, 20, 25) and reaction temperature (25 °C, 40 °C and 60 °C) on the catalytic properties of supported Fe catalysts are studied. Our results highlight the role of CeO2 and the calcination of the catalyst to obtain the highest catalytic properties after 10 min: 73% of p–HBZ conversion and 52% of total organic carbon (TOC) abatement.

Sign in / Sign up

Export Citation Format

Share Document