scholarly journals BEHAVIOUR OF HIGH-STRENGTH CONCRETE CIRCULAR COLUMNS CONFINED BY HIGH-STRENGTH SPIRALS UNDER CONCENTRIC COMPRESSION

2020 ◽  
Vol 26 (6) ◽  
pp. 564-578
Author(s):  
Chongchi Hou ◽  
Wenzhong Zheng ◽  
Wei Chang
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Concrete Columns ◽  
Confined Concrete ◽  
Concrete Compressive Strength ◽  
Strength Concrete ◽  
Proposed Model ◽  
High Strength Concrete Columns

This paper tested the behaviour of 32 high-strength concrete columns confined by high-strength spirals under concentric compression. The test parameters included unconfined concrete compressive strength, spiral yield strength, volumetric ratio, and spiral spacing. The results showed that bulging and shear sliding were the two characteristic types of failure patterns of the thirty-two confined columns, depending on spiral spacing and concrete strength. Moreover, the spiral in most specimens did not yield at the confined concrete compressive strength. An analytical confinement model for high-strength concrete columns confined by high-strength spirals was proposed. In this proposed model, the calculated value of the spiral stress at the confined concrete compressive strength was used to calculate the feature points of the stressstrain curve. The proposed model showed good correlations with available experimental results of 64 columns.

Loading Process Simulation of GFRP Tube Filled with Steel-Reinforced High-Strength Concrete Columns Subjected to Eccentric Compression

2011 ◽  
Vol 71-78 ◽  
pp. 4203-4206
Author(s):  
Le Zhou ◽  
Hong Tao Liu
Keyword(s):  
High Strength Concrete ◽  
Slenderness Ratio ◽  
Concrete Strength ◽  
High Strength ◽  
Concrete Columns ◽  
Composite Columns ◽  
Strength Concrete ◽  
Finite Strip Method ◽  
Eccentric Compression ◽  
High Strength Concrete Columns

For the further study of bearing compressive capacity of GFRP tube filled with SHC（steel-reinforced high-strength concrete）columns subjected to eccentric compression, and analysis its whole bearing compressive process under eccentric compression. Based on the flat section assumption finite strip method, the calculating program of bearing eccentric compressive capacity of GFRP tube filled with SHC columns is proposed according to existing retrofit theory and related technical procedures. The relation curves of load-deformation is gotten using this calculating program, at the same time it can get the effect curves of concrete strength, slenderness ratio, eccentricity and containing bone rate to load-deformation. Calculations show that the ultimate bearing compressive capacity of composite column decreases with the increase of slenderness ratio, and elastic stage of component curve gradually shortens and stiffness gradually loses; The ultimate bearing compressive capacity of composite columns decreases with the increase of eccentricity; component ductility improves; the ultimate bearing compressive capacity of composite columns increases with the increase of concrete strength. The calculated results agree well with the experimental results and this study provides a basis for practical design.

Background to seismic design provisions in CSA A23.3–04 for high-strength concrete

2009 ◽  
Vol 36 (4) ◽  
pp. 565-579 ◽  
Author(s):  
Patrick Paultre ◽  
Denis Mitchell
Keyword(s):  
Compressive Strength ◽  
Seismic Design ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
Concrete Structures ◽  
High Strength ◽  
Frame Structure ◽  
Concrete Compressive Strength ◽  
Strength Concrete ◽  
Loading Tests

This paper presents the background experimental and analytical research that was carried out to develop the provisions for the seismic design of high-strength concrete structures in the 2004 Canadian standard CSA A23.3–04. It is noted that the 1994 Canadian standard CSA A23.3–94 limited the concrete compressive strength to 55 MPa for the seismic design of nominally ductile and ductile structures, while the 1995 New Zealand Standard limited the concrete compressive strength to 70 MPa. In contrast, the 2008 American Concrete Institute (ACI) code ACI 318M has no upper limit on concrete strength, even for the seismic design of ductile structural elements. This tremendous variation in these limits indicated that more experimental evidence was needed. This paper presents experimental results of reversed cyclic loading tests on large-scale structural components as well as simulated seismic loading tests of a frame structure constructed with high-strength concrete. The goal of this collaborative research program at the University of Sherbrooke and McGill University was to determine the seismic design and detailing requirements for high-strength concrete structures to achieve the desired level of ductility and energy dissipation. The experimental programs include full-scale testing of the following: columns subjected to a pure axial load (square and circular columns); columns subjected to flexure and axial loads; beam-column subassemblages (square and circular columns); coupling beams in coupled wall structures; shear walls and a two-storey, three-dimensional frame structure. The results of the responses of the high-strength concrete structural specimens are compared with the responses of companion specimens constructed with normal-strength concrete.

Sign in / Sign up

Export Citation Format

Share Document