scholarly journals Development and verification of CFD model of carbothermal synthesis furnace for production of mixed nitride uranium-plutonium fuel

2020 ◽  
Vol 6 (1) ◽  
pp. 37-42
Author(s):  
Rinat N. Shamsutdinov ◽  
Sergey V. Pavlov ◽  
Anton Yu. Leshchenko
Keyword(s):  
Experimental Data ◽  
Gas Flow ◽  
Flow Simulation ◽  
Furnace Operation ◽  
Cfd Model ◽  
Simulation Code ◽  
Cooling Rates ◽  
Heating And Cooling ◽  
Carbothermal Synthesis ◽  
Uranium Plutonium

The retort batch furnace for the carbothermal synthesis of uranium and plutonium nitrides is a component of the mixed nitride uranium-plutonium (MNUP) fuel Fabrication/Refabrication Module (FRM), a part of the Pilot Demonstration Energy Complex (PDEC). A CFD model of the furnace was built in the SolidWorks Flow Simulation code to check the feasibility of its thermophysical operating modes (heating and cooling rates, temperature of the product loaded into the furnace). The experimental data obtained from the performance tests was used to verify the developed CFD model and to confirm its adequacy. The relative deviation of the calculated temperature of the loaded product from the experimental data in the process of isothermal annealing does not exceed 0.7%. The temperatures of the loaded product predicted by the CFD model were used to justify engineering solutions for the uranium and plutonium nitrides carbothermal synthesis furnace. The CFD model can be used to define the furnace operation mode by selecting the gas flow rates inside and outside the retort, the heater temperature, and heating and cooling rates for the product loaded in the furnace.

scholarly journals Development and verification of CFD model of furnace for carbothermal synthesis of mixed nitride uranium-plutonium fuel

2019 ◽  
Vol 2019 (4) ◽  
pp. 130-141
Author(s):  
Rinat Nurislamovich Shamsutdinov ◽  
Sergej Vladlenovich Pavlov ◽  
Leshchenko A.Yu. Leshchenko
Keyword(s):  
Cfd Model ◽  
Carbothermal Synthesis ◽  
Uranium Plutonium ◽  
Plutonium Fuel

Texture Evolution Under Fast Heating and Cooling Rates of Zirconium Alloys Studied In-Situ by Synchrotron X-Ray Diffraction

2020 ◽  
Author(s):  
Chi-Toan Nguyen ◽  
Alistair Garner ◽  
Javier Romero ◽  
Antoine Ambard ◽  
Michael Preuss ◽  
...  
Keyword(s):  
Texture Evolution ◽  
Zirconium Alloys ◽  
X Ray Diffraction ◽  
Fast Heating ◽  
Cooling Rates ◽  
X Ray ◽  
Heating And Cooling

Effects of Over Fire Air on the Combustion and NOx Emission Characteristics of a 600 MW Opposed Swirling Fired Boiler

2012 ◽  
Vol 512-515 ◽  
pp. 2135-2142 ◽  
Author(s):  
Yu Peng Wu ◽  
Zhi Yong Wen ◽  
Yue Liang Shen ◽  
Qing Yan Fang ◽  
Cheng Zhang ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Empirical Method ◽  
Nox Emission ◽  
Emission Characteristics ◽  
Cfd Model ◽  
Nitrogen Release ◽  
Computational Fluid Dynamics Cfd ◽  
Low Nox Emission

A computational fluid dynamics (CFD) model of a 600 MW opposed swirling coal-fired utility boiler has been established. The chemical percolation devolatilization (CPD) model, instead of an empirical method, has been adapted to predict the nitrogen release during the devolatilization. The current CFD model has been validated by comparing the simulated results with the experimental data obtained from the boiler for case study. The validated CFD model is then applied to study the effects of ratio of over fire air (OFA) on the combustion and nitrogen oxides (NOx) emission characteristics. It is found that, with increasing the ratio of OFA, the carbon content in fly ash increases linearly, and the NOx emission reduces largely. The OFA ratio of 30% is optimal for both high burnout of pulverized coal and low NOx emission. The present study provides helpful information for understanding and optimizing the combustion of the studied boiler

scholarly journals Influence of center gas supply device on gas–solid flow in COREX shaft furnace through DEM–CFD model

2020 ◽  
Vol 18 (5-6) ◽  
Author(s):  
Heng Zhou ◽  
Shuyu Wang ◽  
Binbin Du ◽  
Mingyin Kou ◽  
Zhiyong Tang ◽  
...  
Keyword(s):  
Gas Flow ◽  
Shaft Furnace ◽  
Middle Zone ◽  
Cfd Model ◽  
Gas Velocity ◽  
Gas Distribution ◽  
Particle Segregation ◽  
Solid Flow ◽  
Corex Shaft Furnace ◽  
Gas Supply

AbstractIn order to develop the central gas flow in COREX shaft furnace, a new installment of center gas supply device (CGD) is designed. In this work, a coupled DEM–CFD model was employed to study the influence of CGD on gas–solid flow in COREX shaft furnace. The particle descending velocity, particle segregation behaviour, void distribution and gas distribution were investigated. The results show that the CGD affects the particles descending velocity remarkably as the burden falling down to the slot. Particle segregation can be observed under the inverse ‘V’ burden profile, and the influence of CGD on the particle segregation is unobvious on the whole, which causes the result that the voidage is slightly changed. Although the effect of CGD on solid flow is not significant, the gas flow in shaft furnace has an obvious change. Compared with the condition without CGD, in the case with CGD, the gas velocity is improved significantly, especially in the middle zone of the furnace, which further promotes the center gas distribution. Meanwhile, the pressure drop in the furnace with the installation of CGD is increased partly.

Modified methodology of computation of admissible continuous currents of plain conductors of overhead transmission lines and catenaries

2021 ◽  
Vol 2 (2) ◽  
pp. 36-43
Author(s):  
Evgeniy P. FIGURNOV ◽  
◽  
Yury I. ZHARKOV ◽  
Valeriy I. KHARCHEVNIKOV ◽  
◽  
...  
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Transmission Lines ◽  
Power Transmission ◽  
Convection Heat Transfer ◽  
Heating And Cooling ◽  
Continuous Current ◽  
The Subject ◽  
The Common ◽  
Overhead Power Transmission Line

Methodology provided summarizes published, original and foreign theoretic and experimental data on the subject of heating and cooling of standard and shaped conductors of overhead power transmission line and uses those of them which are most affected to fundamental heat-transfer laws. Computation surface area of standard and shaped wire formulas are given. The common formula of convection heat transfer coefficient is provided, based on wind speed and direction, concerning antiicing mode. Parameters of this formula do not coincide with those existing, as they are based on experimental data on standard and shaped conductors but not on round tubes. Formula of computation of heat transfer power under the influence of solar radiation is given. Summarized formula of admissible continuous current computation is given, all the components have detailed description in the article.

Performance Characterization of a Twin Scroll Volute for Turbocharging Applications

2018 ◽  
Author(s):  
Carlo Cravero ◽  
Mario La Rocca ◽  
Andrea Ottonello
Keyword(s):  
Experimental Data ◽  
Scientific Literature ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Automatic Design ◽  
Cfd Model ◽  
Radial Turbine ◽  
Wide Range ◽  
Partial Admission

The use of twin scroll volutes in radial turbine for turbocharging applications has several advantages over single passage volute related to the engine matching and to the overall compactness. Twin scroll volutes are of increasing interest in power unit development but the open scientific literature on their performance and modelling is still quite limited. In the present work the performance of a twin scroll volute for a turbocharger radial turbine are investigated in some detail in a wide range of operating conditions at both full and partial admission. A CFD model for the volute have been developed and preliminary validated against experimental data available for the radial turbine. Then the numerical model has been used to generate the database of solutions that have been investigated and used to extract the performance. Different parameters and indices are introduced to describe the volute aerodynamic performance in the wide range of operating conditions chosen. The above parameters can be used for volute development or matching with a given rotor or efficiently implemented in automatic design optimization strategies.

Coupled Heat and Mass Transfer CFD Model for Methane Hydrate

2015 ◽  
Author(s):  
Eugenio Turco Neto ◽  
M. A. Rahman ◽  
Syed Imtiaz ◽  
Thiago dos Santos Pereira ◽  
Fernanda Soares de Sousa
Keyword(s):  
Natural Gas ◽  
Multiphase Flow ◽  
Gas Hydrate ◽  
Gas Flow ◽  
Three Dimensional ◽  
Hydrate Formation ◽  
Cfd Model ◽  
Flow Metering ◽  
Ansys Cfx ◽  
Gas Hydrate Formation

The gas hydrates problem has been growing in offshore deep water condition where due to low temperature and high pressure hydrate formation becomes more favorable. Several studies have been done to predict the influence of gas hydrate formation in natural gas flow pipeline. However, the effects of multiphase hydrodynamic properties on hydrate formation are missing in these studies. The use of CFD to simulate gas hydrate formation can overcome this gap. In this study a computational fluid dynamics (CFD) model has been developed for mass, heat and momentum transfer for better understanding natural gas hydrate formation and its migration into the pipelines using ANSYS CFX-14. The problem considered in this study is a three-dimensional multiphase-flow model based on Simon Lo (2003) study, which considered the oil-dominant flow in a pipeline with hydrate formation around water droplets dispersed into the oil phase. The results obtained in this study will be useful in designing a multiphase flow metering and a pump to overcome the pressure drop caused by hydrate formation in multiphase petroleum production.

Sign in / Sign up

Export Citation Format

Share Document