scholarly journals Thermo-Mechanical Analysis on Thermal Deformation of Thin Stainless Steel in Laser Micro-Welding

2016 ◽  
Vol 6 (2) ◽  
pp. 51-66 ◽  
Author(s):  
Mohd Idris Shah Ismail ◽  
Yasuhiro Okamoto ◽  
Akira Okada
Keyword(s):  
Finite Element ◽  
Stainless Steel ◽  
Finite Element Model ◽  
High Speed ◽  
Continuous Wave ◽  
Element Model ◽  
Scanning System ◽  
Welding Deformation ◽  
Scanning Velocity ◽  
Stress And Deformation

In the present study, a three-dimensional finite element model has been developed to simulate the temperature, stress and deformation fields in continuous wave (CW) laser micro-welding of thin stainless steel sheet. The welding deformation was experimentally evaluated using a single-mode fiber laser with a high-speed scanning system. Application of developed thermal model demonstrated that the laser parameters, such as laser power, scanning velocity and spot diameter have a significant effect on temperature field and the weld pool. In the case of welding deformation, numerical simulation was carried out by an uncoupled thermo-mechanical model. The welding stress and deformation are generated by plastic deformation during the heating and cooling periods. It was confirmed that the residual stress is higher than yield strength and has strongest effect upon the welding deformation. The numerical simulated results have proved that the developed finite element model is effective to predict thermal histories, thermally induced stresses and welding deformations in the thin material.

scholarly journals Comparative Analysis of Static Loading Performance of Rigid and Flexible Road Wheel based on Finite Element Method

2020 ◽  
Vol 70 (1) ◽  
pp. 41-46
Author(s):  
Yaoji Deng ◽  
Youqun Zhao ◽  
Mingmin Zhu ◽  
Zhen Xiao ◽  
Qiuwei Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Static Loading ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Vertical Load ◽  
New Type ◽  
Stress And Deformation ◽  
Nonlinear Finite Element Model

To overcome the shortcomings of traditional rigid road wheel, such as poor damping effect and low load-bearing efficiency, a new type of flexible road wheel, having a unique suspension-bearing mode, was introduced. The three-dimensional nonlinear finite element model of rigid and flexible road wheel, considering the triple nonlinear characteristics of geometry, material and contact, is established for numerical investigation of static loading performance. The accuracy of the finite element model of the rigid and flexible road wheel is verified by static loading experiment. The static loading performance of the rigid and flexible road wheels is numerically analyzed. The influence of vertical load on maximum stress and deformation of the rigid and flexible wheels is also studied. The results show that the contact pressure uniformity of the flexible road wheel is better than that of the rigid road wheel under the static vertical load, but the maximum stress and deformation of the flexible road wheel are greater than that of the rigid road wheel. However, this problem can be solved by increasing the number of hinge sets and optimising the joints. The research results provide theoretical basis for replacing rigid road wheel with flexible road wheel, and also provide reference for structural optimisation of flexible road wheel.

Simulation and Experimental Research on Milling Force of High Manganese Steel

2010 ◽  
Vol 143-144 ◽  
pp. 863-867
Author(s):  
Yong Tang ◽  
Qiang Wu ◽  
Xiao Fang Hu ◽  
Yu Zhong Li
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
High Speed ◽  
Shear Failure ◽  
Element Model ◽  
Manganese Steel ◽  
High Manganese ◽  
Milling Force ◽  
High Manganese Steel ◽  
High Speed Milling

The milling process of hard-to-cut material high manganese steel ZGMn13 was simulated and experimental studied based on Johnson-Cook material model and shear failure model.The high speed milling processing finite element model has established adopting arbitrary Lagrangian-Euler method (ALE) and the grid adaptive technology,The influence of milling parameters to milling force is analyzed in the high speed milling high manganese steel process. The simulated and experimental results being discussed are matched well. It certifies the finite element model is correct.

Finite Element Modeling of Selective Laser Melting 316L Stainless Steel Parts for Evaluating the Mechanical Properties

2016 ◽  
Author(s):  
Arman Ahmadi ◽  
Narges Shayesteh Moghaddam ◽  
Mohammad Elahinia ◽  
Haluk E. Karaca ◽  
Reza Mirzaeifar
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Stainless Steel ◽  
Finite Element Model ◽  
Grain Boundaries ◽  
Mechanical Response ◽  
Element Model ◽  
Polycrystalline Materials ◽  
Microstructural Properties ◽  
Laser Melting

Selective laser melting (SLM) is an additive manufacturing technique in which complex parts can be fabricated directly by melting layers of powder from a CAD model. SLM has a wide range of application in biomedicine and other engineering areas and it has a series of advantages over traditional processing techniques. A large number of variables including laser power, scanning speed, scanning line spacing, layer thickness, material based input parameters, etc. have a considerable effect on SLM process materials. The interaction between these parameters is not completely studied. Limited studies on balling effect in SLM, densifications under different processing conditions, and laser re-melting, have been conducted that involved microstructural investigation. Grain boundaries are amongst the most important microstructural properties in polycrystalline materials with a significant effect on the fracture and plastic deformation. In SLM samples, in addition to the grain boundaries, the microstructure has another set of connecting surfaces between the melt pools. In this study, a computational framework is developed to model the mechanical response of SLM processed materials by considering both the grain boundaries and melt pool boundaries in the material. To this end, a 3D finite element model is developed to investigate the effect of various microstructural properties including the grains size, melt pools size, and pool connectivity on the macroscopic mechanical response of the SLM manufactured materials. A conventional microstructural model for studying polycrystalline materials is modified to incorporate the effect of connecting melt pools beside the grain boundaries. In this model, individual melt pools are approximated as overlapped cylinders each containing several grains and grain boundaries, which are modeled to be attached together by the cohesive zone method. This method has been used in modeling adhesives, bonded interfaces, gaskets, and rock fracture. A traction-separation description of the interface is used as the constitutive response of this model. Anisotropic elasticity and crystal plasticity are used as constitutive laws for the material inside the grains. For the experimental verification, stainless steel 316L flat dog bone samples are fabricated by SLM and tested in tension. During fabrication, the power of laser is constant, and the scan speed is changed to study the effect of fabrication parameters on the mechanical properties of the parts and to compare the result with the finite element model.

Validation of a New Finite Element Model for Human Knee Ligaments for Use in High Speed Automotive Collisions

2009 ◽  
Author(s):  
Chiara Silvestri ◽  
Louis R. Peck ◽  
Kristen L. Billiar ◽  
Malcolm H. Ray
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Strain Rate ◽  
High Speed ◽  
Element Model ◽  
Knee Ligament ◽  
Knee Ligaments ◽  
Human Knee ◽  
Dynamic Representation ◽  
Failure Properties

A finite element model of knee human ligaments was developed and validated to predict the injury potential of occupants in high speed frontal automotive collisions. Dynamic failure properties of ligaments were modeled to facilitate the development of more realistic dynamic representation of the human lower extremities when subjected to a high strain rate. Uniaxial impulsive impact loads were applied to porcine medial collateral ligament-bone complex with strain rates up to145 s−1. From test results, the failure load was found to depend on ligament geometric parameters and on the strain rate applied. The information obtained was then integrated into a finite element model of the knee ligaments with the potential to be used also for representation of ligaments in other regions of the human body. The model was then validated against knee ligament dynamic tolerance tests found in literature. Results obtained from finite element simulations during the validation process agreed with the outcomes reported by literature findings encouraging the use of this ligament model as a powerful and innovative tool to estimate ligament human response in high speed frontal automotive collisions.

scholarly journals Simulation Analysis of a Multiple-Vehicle, High-Speed Train Collision Using a Simplified Model

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Suchao Xie ◽  
Weilin Yang ◽  
Ping Xu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
High Speed ◽  
Large Scale ◽  
Computing Time ◽  
Element Model ◽  
Vehicle Body ◽  
Railway Vehicle ◽  
Storage Space ◽  
High Speed Train

To solve the problems associated with multiple-vehicle simulations of railway vehicles including large scale modelling, long computing time, low analysis efficiency, need for high performance computing, and large storage space, the middle part of the train where no plastic deformation occurs in the vehicle body was simplified using mass and beam elements. Comparative analysis of the collisions between a single railway vehicle (including head and intermediate vehicles before, and after, simplification) and a rigid wall showed that variations in impact kinetic energy, internal energy, and impact force (after simplification) are consistent with those of the unsimplified model. Meanwhile, the finite element model of a whole high-speed train was assembled based on the simplified single-vehicle model. The numbers of nodes and elements in the simplified finite element model of the whole train were 63.4% and 61.6%, respectively, compared to those of the unsimplified model. The simplified whole train model using the above method was more accurate than the multibody model. In comparison to the full-size finite element model, it is more specific, had more rapid computational speed, and saved a large amount of computational power and storage space. Finally, the velocity and acceleration data for every car were discussed through the analysis of the collision between two simplified trains at various speeds.

Modal Analysis of BT Spindle-Toolholder Interface Based on Abaqus/Standard

2013 ◽  
Vol 662 ◽  
pp. 632-636
Author(s):  
Yong Sheng Zhao ◽  
Jing Yang ◽  
Xiao Lei Song ◽  
Zi Jun Qi
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Modal Analysis ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Element Model ◽  
Contact Theory ◽  
High Speed Machining ◽  
The Finite Element Model

The quality of high speed machining is directly related to dynamic characteristics of spindle-toolholder interface. The paper established normal and tangential interactions of BT spindle-toolholder interface based on finite element contact theory, and analysed free modal in Abaqus/Standard. Then the result was compared with the experimental modal analysis. It shows that the finite element model is effective and could be applied in the future dynamic study of high-speed spindle system.

Sign in / Sign up

Export Citation Format

Share Document