scholarly journals Synthesis of the Fe-6.5% wt. Si Alloy by Mechanical Alloying

2015 ◽  
Vol 13 ◽  
pp. 109-113 ◽  
Author(s):  
Cristina Daniela Stanciu ◽  
Florin Popa ◽  
Ionel Chicinaş ◽  
Olivier Isnard
Keyword(s):  
Mechanical Alloying ◽  
High Energy ◽  
Alloy Formation ◽  
X Ray Diffraction ◽  
Nanocrystalline State ◽  
Compound Formation ◽  
Dsc Studies ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
Si Content

Fe-Si alloy with a large Si content of 6.5 wt. % is obtained in nanocrystalline state by mechanical alloying of elemental iron and silicon powders. The mechanical alloying process was carried out using a high energy ball mill in argon atmosphere. Samples were collected after 0.5, 1, 2, 4, 6 and 8 hours of ball milling. The X-ray diffraction (XRD) studies indicate that after 4 hours of milling the Fe-Si alloy is formed. The powder magnetisation decreases upon increasing the milling time up to 4 hours as a consequence of the Fe-Si alloy formation. Upon heating, the DSC studies show the Fe3Si compound formation in the samples milled for milling times lower than 6 hours. Also, the Curie temperature of the alloy was evidenced.

Synthesis of the Fe-10%Si Nanocrystalline Powder by Mechanical Alloying

2014 ◽  
Vol 216 ◽  
pp. 283-287 ◽  
Author(s):  
Cristina Daniela Stanciu ◽  
Traian Florin Marinca ◽  
Florin Popa ◽  
Ionel Chicinaş ◽  
Olivier Isnard
Keyword(s):  
Mechanical Alloying ◽  
High Energy ◽  
Milling Process ◽  
Nanocrystalline Powder ◽  
Alloy Formation ◽  
X Ray Diffraction ◽  
Nanocrystalline State ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
Si Content

Fe-Si alloy with a Si content of 10 wt. % was obtained in nanocrystalline state by mechanical alloying of elemental iron and silicon powders. The mechanical alloying process was carried out in a high energy ball mill (Fritsch, Pulverisette 4) in argon atmosphere. The X-ray diffraction (XRD) studies indicated that after 4 hours of milling the Fe-Si alloy is formed. The mean crystallites size decreases down to 7 nm after 8 hours of milling. The particles morphology investigated by scanning electron microscopy (SEM) showed an evolution during milling process from two different kinds of particles to a one kind of particles with irregular shape. The magnetisation of powders decreases upon increasing the milling time up to 4 hours as a consequence of the Fe-Si alloy formation.

SYNTHESIS OF NANO-CRYSTALLINE Cu-Cr ALLOY BY MECHANICAL ALLOYING

2012 ◽  
Vol 05 ◽  
pp. 496-501 ◽  
Author(s):  
S. SHEIBANI ◽  
S. HESHMATI-MANESH ◽  
A. ATAIE
Keyword(s):  
Mechanical Alloying ◽  
Structural Evolution ◽  
High Energy ◽  
Lattice Parameter ◽  
Control Agent ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Nano Crystalline ◽  
High Energy Ball Mill ◽  
Energy Ball

In this paper, the influence of toluene as the process control agent (PCA) and pre-milling on the extension of solid solubility of 7 wt.% Cr in Cu by mechanical alloying in a high energy ball mill was investigated. The structural evolution and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques, respectively. The solid solution formation at different conditions was analyzed by copper lattice parameter change during the milling process. It was found that both the presence of PCA and pre-milling of Cr powder lead to faster dissolution of Cr . The mean crystallite size was also calculated and showed to be about 10 nm after 80 hours of milling.

The Investigation of Structural and Magnetic Properties at High-Temperature of Nanostructured Fe90-Mg10 Alloys Produced by Mechanical Alloying

2018 ◽  
Vol 54 ◽  
pp. 136-145
Author(s):  
A. El Mohri ◽  
M. Zergoug ◽  
K. Taibi ◽  
M. Azzaz
Keyword(s):  
High Temperature ◽  
Mechanical Alloying ◽  
Milling Time ◽  
High Energy ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
High Energy Ball Mill ◽  
Energy Ball ◽  
The Mean

Nanocrystalline Fe90Mg10 alloy samples were prepared by mechanical alloying process using planetary high energy ball mill. The prepared powders were characterized using differential thermal analysis (DTA), X-ray diffraction technique (XRD) at high temperature, transmission electron microscopy (TEM), and the vibrating sample magnetometer (VSM). Obtained results are discussed according to milling time. XRD at high temperature results also indicated that when the milling time increases, the lattice parameter and the mean level of grain size increase, whereas the microstrains decrease. The result of the observation by the TEM of the Fe-Mg powders prepared in different milling time, coercive fields derived and Saturation magnetization derived from the hysteresis curves in high temperature are discussed as a function of milling time.

Phase Transformation in Al3Ni2 Alloy during Mechanical Alloying and Heating of Milling Products

2013 ◽  
Vol 203-204 ◽  
pp. 272-275
Author(s):  
Marek Krasnowski ◽  
Tadeusz Kulik
Keyword(s):  
Mechanical Alloying ◽  
Phase Transformations ◽  
Intermetallic Phase ◽  
Diffraction Method ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
High Energy Ball Mill ◽  
Elemental Powder Mixture ◽  
Energy Ball

An elemental powder mixture corresponding to the Al3Ni2 phase stoichiometry was subjected to mechanical alloying in a high-energy ball mill. Products of this process after various milling times were investigated by differential scanning calorimetry. The phase transformations occurring in the material throughout milling and during heating in a calorimeter were investigated by X-ray diffraction method. This study revealed that a metastable nanocrystalline NiAl intermetallic phase was formed during the mechanical alloying process. Heating of the synthesised powders in the calorimeter caused phase transformations, the product of which was an equilibrium Al3Ni2 intermetallic phase or a mixture of NiAl, Al3Ni2 and Al3Ni intermetallic phases, depending on the milling time and the temperature up to which the material was heated.

scholarly journals Pengamatan In-Situ Tekanan dan Temperatur pada Pembentukan MgH2/Ni melalui Metode Reactive Mechanical Alloying (RMA) untuk Aplikasi Material Penyimpan Hidrogen

2017 ◽  
Vol 4 (02) ◽  
pp. 156
Author(s):  
Erfan Handoko ◽  
Aditia Pradipta ◽  
Bambang Soegijono ◽  
Zulkarnain Jalil
Keyword(s):  
Mechanical Alloying ◽  
High Energy ◽  
X Ray Diffraction ◽  
Sem Image ◽  
High Energy Ball Mill ◽  
Measurement Results ◽  
Energy Ball ◽  
Material Forming ◽  
Reactive Mechanical Alloying

<p>The observation on reactive mechanical alloying (RMA) process had been done to form MgH2 material with adding Ni nanoparticles as catalist for hydrogen storage material applications. Pressure and temperature of material forming were recorded by microcontroller set for 30 minutes. Mg with adding Ni 5 wt % was milled by High Energy Ball Mill (HEBM) at H2 atmosphere in 1 atm of pressure. The measurement results showed that the pressure had been changed and temperature also changes up to 38oC. This process proves that the alloying betwen Mg and H2 had been formed. The X-ray diffraction pattern identify MgH2 phase. SEM image showed the morphology of MgH2 particles.</p>

Microstructural Evolution of Cr-Ta Powder in the Process of Mechanical Alloying

2015 ◽  
Vol 1094 ◽  
pp. 300-304
Author(s):  
Jing Yao ◽  
Shi Qiang Lu ◽  
Xuan Xiao
Keyword(s):  
Mechanical Alloying ◽  
Ball Mill ◽  
Supersaturated Solid Solution ◽  
High Energy ◽  
Mass Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
High Energy Ball Mill ◽  
The Hours ◽  
Energy Ball

High energy ball mill tests under the condition of the ball material mass ratio 13:1 and the rotate speed 400 r/min have been employed to investigate the process of mechanical alloying (MA) of Ta and Cr powder mixed in the mole ratio of 1:2.The microstructure evolution process and phase composition were explained useing scanning electron microscope (SEM) and X-ray diffraction (XRD). The results show that, the milled 20h powder existed in Ta (Cr) supersaturated solid solution and amorphous after 40h. Although the hours were spent on ball milling reached to 50h, Laves phase TaCr2had not been made during the process.

Technological Aspects of Fe-Al-Si Intermetallic Alloy Preparation by Mechanical Alloying

2019 ◽  
Vol 810 ◽  
pp. 101-106 ◽  
Author(s):  
Petr Haušild ◽  
Jaroslav Čech ◽  
Veronika Kadlecová ◽  
Miroslav Karlík ◽  
Filip Průša ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Ball Mill ◽  
High Energy ◽  
Intermetallic Alloy ◽  
Alloyed Powder ◽  
Temperature Oxidation ◽  
High Energy Ball Mill ◽  
Speed Up ◽  
Energy Ball ◽  
Kinetics Of

In this paper, recently developed ternary FeAl20Si20 (wt.%) alloy with promising high-temperature oxidation and wear resistance was prepared by mechanical alloying in a high-energy ball mill. The possibility to speed-up the mechanical alloying process by replacing aluminium (and partly silicon) elemental powder by the pre-alloyed powder (AlSi30) with relatively fine dispersion of Si in the Al-Si eutectic was examined. The microstructure, phase composition and mechanical properties after various time of mechanical alloying were characterized. The effect of using the pre-alloyed powders on kinetics of mechanical alloying is compared with the results obtained on batches prepared from elemental powders.

Obtaining of the Ir-Al Nanocrystalline Powders by Mechanical Alloying

2011 ◽  
Vol 672 ◽  
pp. 171-174
Author(s):  
Ionel Chicinaş ◽  
P. Cârlan ◽  
Florin Popa ◽  
Virgiliu Călin Prică ◽  
Lidia Adriana Sorcoi
Keyword(s):  
Mechanical Alloying ◽  
Particle Morphology ◽  
High Energy ◽  
Atomic Ratio ◽  
Planetary Mill ◽  
Nanocrystalline Powders ◽  
Alloy Formation ◽  
X Ray Diffraction ◽  
Chemical Homogeneity ◽  
Diffraction Patterns

The Ir-Al powder in the 1:1 atomic ratio was obtained by high energy mechanical alloying in a Pulverisette 4 Fritch planetary mill. The final product was obtained after 28 h of milling in argon atmosphere. Alloy formation was investigated by X-ray diffraction. After 4 h of milling the new structure of IrAl compound is found in the diffraction patterns. The obtained powders are nanocrystalline with a mean crystallite size of 11 nm after 28 h of milling. The particle morphology and the chemical homogeneity were studied using scanning electron microscopy (SEM) and energy dispersive spectrometry (EDX). It was found that the obtained compound present large particles composed by smaller one.

Atmosphere effects of the amorphization reaction in NiZr by ball milling

1993 ◽  
Vol 8 (2) ◽  
pp. 307-313 ◽  
Author(s):  
K. Aoki ◽  
A. Memezawa ◽  
T. Masumoto
Keyword(s):  
High Energy ◽  
Hydrogen Atmosphere ◽  
Nitrogen Atmosphere ◽  
Gas Absorption ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
High Energy Ball Mill ◽  
Energy Ball

An intermetallic compound c–NiZr and a mixture of elemental powders of nickel and zirconium [Ni50Zr50 (at. %)] have been mechanically ground (MG) and mechanically alloyed (MA), respectively, using a high-energy ball mill in various atmospheres. The products were characterized by x-ray diffraction, transmission electron microscopy, differential scanning calorimetry, and chemical analysis as a function of milling time. An amorphous a–NiZr alloy was prepared by both MG and MA in an argon atmosphere. By MG of NiZr, an amorphous nitride a–NiZrN0.15 was synthesized in a nitrogen atmosphere, while a crystalline hydride c–NiZrH3 was formed in a hydrogen atmosphere. On the other hand, ZrN and ZrH2 were formed by MA in a nitrogen and a hydrogen atmosphere, respectively. The amorphization reaction was observed between ZrH2 and Ni by further MA in a hydrogen atmosphere, and a mixture of a–NiZrxHy (x < 1) and ZrH2 was obtained. However, no amorphization was observed by MA between ZrN and Ni in a nitrogen atmosphere. The effects of the milling atmosphere on the phase formations during MG and MA are discussed based on the gas absorption rate.

Nickel Silicides Synthesized by High Energy Ball Milling

2007 ◽  
Vol 353-358 ◽  
pp. 1625-1628 ◽  
Author(s):  
Gen Shun Ji ◽  
Qin Ma ◽  
Tie Ming Guo ◽  
Qi Zhou ◽  
Jian Gang Jia ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Ball Milling ◽  
Milling Time ◽  
High Energy ◽  
Planetary Mill ◽  
High Energy Ball Milling ◽  
X Ray Diffraction ◽  
Microstructure Morphology ◽  
Energy Ball ◽  
Xrd Patterns

The high energy ball milling of Ni-50 atom % Si elemental powder mixtures was carried out using a planetary mill. X-ray diffraction (XRD) was used to identify the phase evolutions during the high energy ball milling period. The microstructure morphology of the powders milled different time was determined by field emission scanning electron microscope (FESEM). The beginning time of mechanical alloying was determined by back scattered electrons (BSE) images. The XRD patterns showed that the nickel peaks intensity and the silicon peaks intensity obviously decreased with milling time increased to 1 hour. BSE images revealed that nickel and silicon powders were not blended uniformly for 1 hour of milling. It was found that NiSi formed as the milling time increased to 5 hours, simultaneously, the nickel peaks and the silicon peaks almost disappeared. That means the obvious mechanical alloying started from 5 hours of milling. BSE images agreed with the result analyzed from XRD patterns. With the milling time further increased from 10 to 75 hours, the NiSi peaks decreased gradually, at the same time, the Ni2Si peaks appeared and then increased gradually.

Sign in / Sign up

Export Citation Format

Share Document