Yaw Stability Analysis for UiTM's BWB Baseline-II UAV E-4

2013 ◽  
Vol 393 ◽  
pp. 323-328 ◽  
Author(s):  
Firdaus Mohamad ◽  
Wirachman Wisnoe ◽  
Rizal E.M. Nasir ◽  
Khairul Imran Sainan ◽  
Norhisyam Jenal
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Stability Analysis ◽  
Mach Number ◽  
Deflection Angle ◽  
Rolling Moment ◽  
Yaw Stability ◽  
Directional Motion ◽  
Computational Fluid Dynamics Cfd ◽  
The Stability

This paper presents a study about yaw stability analysis for UiTMs Blended-Wing-Body (BWB) Baseline-II E-4. This aircraft is equipped with split drag flaps in order to perform directional motion. One of the split drag flaps will be deflected to generate yawing moment. This yawing moment is generated through the drag that is produced upon deflection of flaps. The study was carried out using Computational Fluid Dynamics (CFD) for various sideslip angles (β) and various flaps deflection angle (δT). The simulation was conducted at 0.1 Mach number (35 m/s) and results in terms of coefficient such yawing and rolling moment are tabulated in order to determine the stability of the aircraft. The result reveals that the aircraft is directionally unstable. This is as expected because the aircraft does not have any vertical tail configuration to provide the yawing moment. However, high deflection of split flaps can still generate adequate restoring moment for the aircraft.

Effect of Cavities in Suddenly Expanded Flow at Supersonic Mach Number

CFD letters ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 57-71
Author(s):  
Atifatul Ismah Ismail
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Mach Number ◽  
Pressure Ratio ◽  
Area Ratio ◽  
Base Pressure ◽  
Sudden Expansion ◽  
Expansion Level ◽  
Computational Fluid Dynamics Cfd ◽  
Base Drag

The contribution from the base drag due to the sub-atmospheric pressure is significant. It can be more than two-thirds of the net drag. There is a need to increase the base pressure and hence decrease the base drag. This research examines the effect of Mach Number on base pressure. To accomplish this objective, it controls the efficacy in an enlarged duct computed by the numerical approach using Computational Fluid Dynamics (CFD) Analysis. This experiment was carried out by considering the expansion level and the aspect cavity ratio. The computational fluid dynamics method is used to model supersonic motion with the sudden expansion, and a convergent-divergent nozzle is used. The Mach number is 1.74 for the present study, and the area ratio is 2.56. The L/D ratio varied from 2, 4, 6, 8, and 10, and the simulated nozzle pressure ratio ranged from 3 to 11. The two-dimensional planar design used commercial software from ANSYS. The airflow from a Mach 1.74 convergent-divergent axi-symmetric nozzle expanded suddenly into circular ducts of diameters 17 and 24.5 mm with and without annular rectangular cavities. The diameter of the duct is taken D=17mm and D=24.5mm. The C-D nozzle was developed and modeled in the present study: K-ε standard wall function turbulence model was used with the commercial computational fluid dynamics (CFD) and validated. The result indicates that the base pressure is impacted by the expansion level, the enlarged duct size, and the passage’s area ratio.

Computational fluid dynamics analysis of the effect of throat diameter on the fluid flow and performance of ejector

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mohammadreza Salehi ◽  
Nader Pourmahmoud ◽  
Amir Hassanzadeh ◽  
S. Hoseinzadeh ◽  
P.S. Heyns
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Mach Number ◽  
Content Type ◽  
Standard Code ◽  
Computational Fluid Dynamics Analysis ◽  
Fluent Software ◽  
Computational Fluid Dynamics Cfd ◽  
Throat Diameter ◽  
And Performance

Purpose Using the computational fluid dynamics (CFD) technique, this paper aims to investigate the influence of key parameters such as throat diameter; the suction ratio on the flow field behaviors such as Mach number; pressure; and temperature. Design/methodology/approach To investigate the effect of throat diameter, it is simulated for 4, 6, 8 and 10 mm as throat diameters. The governing equations have been solved by standard code of Fluent Software together with a compressible 2 D symmetric and turbulence model with the standard k–ε model. First, the influence of the throat diameter is investigated by keeping the inlet mass flow constant. Findings The results show that a place of shock wave creation is changed by changing the throat diameter. The obtained results illustrate that the maximum amount of Mach number is dependent on the throat diameter. It is obtained from the results that for smaller throats higher Mach numbers can be obtained. Therefore, for mixing purposes smaller throats and for exhausting bigger throats seems to be appropriate. Originality/value The obtained numerical results are compared to the existing experimental ones which show good agreement.

Influence Mechanisms of Manufacture Variations on Supersonic/Transonic Blade Aerodynamic Performances

2020 ◽  
Author(s):  
Baojie Liu ◽  
Jiaxin Liu ◽  
Xianjun Yu ◽  
Dejun Meng ◽  
Wenbin Shi
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Pressure ◽  
Statistical Analysis ◽  
Mach Number ◽  
Systematic Errors ◽  
Aerodynamic Performance ◽  
Aerodynamic Performances ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

Abstract The results of previous studies have proved that manufacture variations can cause a noticeable influence on compressor aerodynamic performance. The main objective of this paper is to investigate the influence rules and mechanisms of manufacture variations on supersonic/transonic blades aerodynamic performance. The variations used in this study were measured from some newly manufactured high-pressure compressors. In the present study, several blade sections with different design Mach number conditions are selected for further statistical analysis of measured deviation data. Therefore, some systematic errors in the deviation data have been revealed. Based on these data, the computational fluid dynamics (CFD) method has been used to obtain the aerodynamic performances of a large number of the measured blade elements. And then, the analysis of the influence rules of manufacture variations on blade aerodynamic performance in different Mach number conditions has been carried out. The present results indicate that the effects of manufacture variations on blade aerodynamic performance in the lower Mach number (0.8) condition are much more significant comparing to that in the higher Mach number (0.9∼1.2) conditions. Based on this, influence mechanisms of manufacture variations on positive incidence range and negative incidence range have been analyzed. The differences of influence mechanisms in different Mach number conditions are the focus of research.

A 3D Computational Fluid Dynamics Analysis of the Wells Turbine

2002 ◽  
Author(s):  
John Daly ◽  
Ajit Thakker ◽  
Patrick Frawley ◽  
Elvis Sheik Bajeet
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Mach Number ◽  
Computational Model ◽  
Experimental Results ◽  
Dynamics Analysis ◽  
Cfd Model ◽  
Wells Turbine ◽  
Computational Fluid Dynamics Analysis ◽  
Computational Fluid Dynamics Cfd

This paper deals with the application of Computational Fluid Dynamics (CFD) to the turbulent analysis of the Wells Turbine. The objectives of this work were twofold; firstly to develop and benchmark the 3D CFD model and then to use this model to analyse the airflow through the turbine. The model was analysed as fully turbulent compressible flow using the Fluent™ CFD code. The computational model was first benchmarked against previously published experimental and CFD data for two similar turbines. The computational model accurately predicted the non-dimensional torque and non-dimensional pressure drop, while the efficiency predictions were lower than the experimental results. Predicted location of turbine stall also corresponded well with experimental results. Potential causes for differences between the computational and experimental results are suggested. The computational model was then analysed at both high and low tip Mach number settings and also with and without the tip gap, and these results were discussed.

Influence of Guide Vanes' Angle on Flow Fields of Cylinder Cage Powder Classifier

2012 ◽  
Vol 263-266 ◽  
pp. 843-846 ◽  
Author(s):  
Da Zhi Jiang ◽  
Jing Han
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Flow Behavior ◽  
Air Flow ◽  
Flow Fields ◽  
Guide Vanes ◽  
Flow Field Characteristics ◽  
Computational Fluid Dynamics Cfd ◽  
The Stability

To research guide vanes' influences on flow fields of cylinder cage powder classifier at different angles, a study of guide vanes under 3 different angles is therefore undertaken examining air flow behavior. The investigation of these flow field characteristics made use of the computational fluid dynamics (CFD) to simulate the air flow in the classifier. The results indicate that smaller angles of guide vanes can increase velocity but damage the stability of flow fields, and that those larger angles will reduce the velocity.

Sign in / Sign up

Export Citation Format

Share Document