Exploration of EMI in Buck Boost Converter – A Real Time Approach 

2014 ◽  
Vol 573 ◽  
pp. 78-82
Author(s):  
Gopal Janaki ◽  
A. Senthil Kumar
Keyword(s):  
Closed Loop ◽  
Load Condition ◽  
Boost Converter ◽  
Experimental Result ◽  
Loop Control ◽  
Class A ◽  
Linear Load ◽  
Constant Output ◽  
Non Linear Load ◽  
Conducted Emi

This paper explores the level of conducted EMI in a buck boost converter under a non linear load condition based on the CISPR 11 / Class A EMC standard. Here, the buck boost converter was designed to produce a constant output voltage irrespective of load conditions. The closed loop control is designed using dsPIC controller. Three different randomization firing schemes are adopted and the EMI analysis in each mode is done experimentally. Also, the results are compared with normal PWM scheme. The experimental result shows that in RPWM scheme the emission levels are comparatively low.

scholarly journals Design and Analysis of Multi-Device Interleaved Boost Converter Driving an Induction Motor

2021 ◽  
Vol 850 (1) ◽  
pp. 012036
Author(s):  
R Latha ◽  
S Adharsh Babu ◽  
M Vivek Kumar
Keyword(s):  
Induction Motor ◽  
Electric Vehicles ◽  
Closed Loop ◽  
Boost Converter ◽  
Open Loop ◽  
Power Electronic ◽  
Loop Control ◽  
Interleaved Boost Converter ◽  
Control Methodology ◽  
Electronic Interface

Abstract Electric vehicles are the future of mobility solutions. The electric vehicles are driven by an electric motor with the help of a power electronic interface. The power electronic interface needs to be designed in an efficient way both in mechanical and electrical aspects. This paper proposes the concept of design, simulation and analysis of a 10 kW Multi-Device Interleaved DC-DC Boost Converter (MDIBC) to drive a 4 kW Induction Motor. The motor is driven from the MDIBC through an inverter with SPWM technique. The variation in DC link voltage due to motor is controlled and stabilized to give a constant DC of 400 V. MDIBC consists of semi-controlled switches topology excited by Phase Shifted PWM technique to reduce the ripple current in interleaving inductors. The dual loop control methodology using PI controller is adopted to reduce the ripple in input inductor current and DC link voltage. The open loop simulation and closed loop simulation are done in MATLAB Simulink environment. The simulation results show that the overshoots and steady state error in inductor currents and output voltage are reduced in addition with reduction in current and voltage ripples.

A New Small-Signal AC Model and Closed Loop Control of a Three-Phase Interleaved Boost Converter

2018 ◽  
Vol 9 (1) ◽  
pp. 240
Author(s):  
H.V.Gururaja Rao ◽  
Karuna Mudliyar ◽  
R.C. Mala
Keyword(s):  
Solar Energy ◽  
Closed Loop ◽  
Boost Converter ◽  
Closed Loop Control ◽  
Phase Lag ◽  
Small Signal ◽  
Loop Control ◽  
Boost Converters ◽  
Three Phase ◽  
Interleaved Boost Converter

<table width="593" border="1" cellspacing="0" cellpadding="0"><tbody><tr><td valign="top" width="387"><p>Renewable energy sources are increasingly being used today and solar energy is the most readily and abundantly available energy source. Boost converters are an integral part of any solar energy system. In order to obtain maximum possible energy from the solar system multi-phase interleaved boost converters are used. This paper presents the small-signal ac modelling and closed loop control of three-phase interleaved boost converter. State–space modelling methodology has been adopted to have linearized equivalent model of the boost converter. The interleaved three-phase boost converter is averaged over its one switching period and perturbed with small ac variations and finally linearized around its quiescent point to have a small signal ac model.  Type III compensator is employed to improve the frequency response and closed loop control of three-phase boost converter. The controller design procedure is discussed in detail. The effect of right-half plane zero in non-minimum phase system and the appropriate pole-zero placements to overcome the maximum phase lag in such system is discussed. The compensated closed loop system is tested for load variations to observe the transient response.</p><p> </p></td></tr></tbody></table>

scholarly journals Closed Loop Control of Multilevel Dc-Dc Boost Converter

2019 ◽  
Vol 9 (2) ◽  
pp. 4512-4518
Keyword(s):  
Closed Loop ◽  
Series Resistance ◽  
Boost Converter ◽  
Cell System ◽  
Fuel Cell System ◽  
Closed Loop System ◽  
Pv System ◽  
Suitable Candidate ◽  
Loop Control ◽  
High Output

This paper presents a multilevel DC-DC boost converter (MBC). It is derived from a conventional boost converter just by adding (2N-1) number of capacitors and same number of diodes in order to obtain N levels of output voltage. Its key feature is to convert low input DC to a high output DC at various levels. This feature makes it a suitable candidate for renewable applications like photovoltaic (PV) system, fuel cell system etc. This paper presents a mathematical model of a N level boost converter. Effect of series resistance (ESR) in inductor is analyzed. A closed loop system for a three level MBC is developed and corresponding simulation results are presented.

Sign in / Sign up

Export Citation Format

Share Document