Research on Influence of Concrete Pouring Sequence on Stability of High-Formwork Support System

2014 ◽  
Vol 580-583 ◽  
pp. 2235-2238
Author(s):  
Li Liu ◽  
Ju Chao Wang ◽  
Bo Wang ◽  
Ya Nan Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Support System ◽  
Lateral Displacement ◽  
The Other ◽  
Sudden Increase ◽  
Analysis Software ◽  
Element Analysis ◽  
Loading Process ◽  
Maximum Lateral Displacement

ANSYS finite element analysis software is used to simulate the changes of maximum lateral displacement of the high-formwork support system in different sequences of pouring concrete. In the condition of loading which was applied from one side to the other side, the maximum lateral displacement of the frame had a sudden increase in each loading process. In the condition of loading which was applied symmetrically, the maximum lateral displacement of the high-formwork steadily rising nearly straight with the load applied. So the symmetrical pouring concrete ways is better for the whole stability of the high-formwork.

Influence of Concrete Pouring Sequence on Stability of Different Height High-Formwork Support System

2013 ◽  
Vol 838-841 ◽  
pp. 227-230
Author(s):  
Li Liu ◽  
Fang Wang ◽  
Ju Chao Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Support System ◽  
Lateral Displacement ◽  
Construction Process ◽  
Analysis Software ◽  
Element Analysis ◽  
The Stability

This article used ABAQUS finite element analysis software to established the high-formwork, analyzed effect on stability of the different height formwork by contrasting lateral displacement of various heights, discussed influence of concrete pouring sequence on stability of different height high-formwork support system in the construction process. From the simulated result, it can be seen that with the increase of height, the lateral displacement increased gradually when poured in dissymmetrical way, but the stability of high-formwork decreased, the result also provides evidence for code revision.

Finite Element Analysis and Optimization of the Truss of Installing Wave-Maker Based on ANSYS

2013 ◽  
Vol 313-314 ◽  
pp. 1038-1041
Author(s):  
Shou Jun Wang ◽  
Xing Xiong ◽  
Chao Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Parameters ◽  
Analysis Software ◽  
Element Analysis ◽  
Large Span ◽  
The Finite Element Analysis ◽  
Wave Maker

According to uncertainty of the design parameters for large span truss of installing wave-maker, in order to avoid the waste of materials,the truss is analyzed based on the finite element analysis software ANSYS to find out its weaknesses and various parts of the deformation. On the premise of ensuring the intensity and stiffness, the weight of the truss is reduced by adjusting its sizes and selecting different profiles, so as to achieve the optimization of the truss of installing wave-maker.

Experimental Research on the Magnetic Field Sensitive Polymeric Actuator

2011 ◽  
Vol 287-290 ◽  
pp. 603-607
Author(s):  
Chun Lin Xia ◽  
Yang Fang Wu ◽  
Qian Qian Lu
Keyword(s):  
Magnetic Field ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Energy Conversion ◽  
Experimental Research ◽  
Experimental Results ◽  
Deformation Characteristics ◽  
Analysis Software ◽  
Element Analysis ◽  
The Magnetic Field

Using domestic MFSP membrane as a medium of energy conversion, a kind of MFSP actuator was designed. The dedicated test equipment was constructed for experimental research, and the experimental results were given. The strip and circular MSFP membrane were analyzed qualitatively to obtain the deformation characteristics of membrane by finite element analysis software.

CAD/CAE on the Mould Plates of Vertical Type High-Pressure Grouting Machine

2012 ◽  
Vol 538-541 ◽  
pp. 2681-2684
Author(s):  
Zhi Cheng Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
3D Model ◽  
Stress And Strain ◽  
Analysis Software ◽  
Element Analysis ◽  
Pressure Grouting ◽  
Object Of Study

Took a type of ceramics for daily use vertical type high pressure grouting machine as the object of study, study the stress and strain of its upper and lower mould plates. Established their 3D model by CAD software Pro-E, and then import them into finite element analysis software to analysis the value and distribution of the stress and strain. The analysis results can provide some reference for design, and have some engineering and practical value.

Development of Finite Element Analysis Support System Based on the Hybrid Knowledge Model

1992 ◽  
Author(s):  
S. Nagasawa ◽  
H. Sakuta ◽  
M. Goto
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Support System ◽  
System Development ◽  
Object Oriented ◽  
Data Representation ◽  
General Purpose ◽  
Element Analysis ◽  
Intelligent Support ◽  
Hierarchical Representation

Abstract This paper deals with conceptual orientation and system development of intelligent support system for general purpose FEA (finite element analysis) programs. An integrated support system called “InhierTalk” (Integrated interactive environment for hierarchical representation for FEA) has been developed in Smalltalk, an object oriented language, in order to confirm effectivity of hierarchical representation and to establish an optimum method of the system development. Two object-oriented knowledge models which consist of macro visual data representation and micro regularized data representation are proposed. In the development, it is found to be clear that active and passive evaluation methods are effective for construction of support system.

Sign in / Sign up

Export Citation Format

Share Document