Preparation and Properties of Graphene and its Nanocomposites

2015 ◽  
Vol 719-720 ◽  
pp. 141-144
Author(s):  
Chen Chi M. Ma ◽  
Sheng Tsung Hsiao ◽  
Wei Hao Liao ◽  
Shin Ming Li ◽  
Yu Sheng Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Hybrid Materials ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Fractured Surface ◽  
Scanning Electron

This study proposed a method to improve the mechanical properties and thermal conductivity of epoxy composites by incorporating multi-walled carbon nanotubes (MWCNTs) and multi-graphene platelets (MGPs) hybrid materials. The MWCNT can bridge adjacent MGPs and inhibit their aggregation effectively, leading to an increased contact surface area between MGP/MWCNT hybrid materials and epoxy matrix. From observing the fractured surface of composite by scanning electron microscope, MWCNT/MGP hybrid materials exhibited better compatibility than individual MWCNT and MGP did.The tensile strength of GD400-MWCNT/MGP/epoxy composites was 35.4% higher than that of epoxy, compared to only a 0.9% increase in tensile strength for MGP/epoxy composites. Thermal conductivity enhanced by 146.9% through incorporating MWCNT/MGP hybrid materials and 23.9% for MGP fillers, compared to non-derivatised epoxy.

The influence of functionalization time of carbon nanotube on the mechanical properties of the epoxy composites

2017 ◽  
Vol 51 (12) ◽  
pp. 1693-1701 ◽  
Author(s):  
EA Zakharychev ◽  
EN Razov ◽  
Yu D Semchikov ◽  
NS Zakharycheva ◽  
MA Kabina
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Carbon Nanotube ◽  
Composite Materials ◽  
Polymer Composites ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

This paper investigates the structure, length, and percentage of functional groups of multi-walled carbon nanotubes (CNT) depending on the time taken for functionalization in HNO3 and H2SO4 mixture. The carbon nanotube content and influence of functionalization time on mechanical properties of polymer composite materials based on epoxy matrix are studied. The extreme dependencies of mechanical properties of carbon nanotube functionalization time of polymer composites were established. The rise in tensile strength of obtained composites reaches 102% and elastic modulus reaches 227% as compared to that of unfilled polymer. The composites exhibited best mechanical properties by including carbon nanotube with 0.5 h functionalization time.

scholarly journals Polymeric Composites Based on Polyurea Matrix Reinforced with Carbon Nanotubes

2017 ◽  
Vol 54 (1) ◽  
pp. 41-44 ◽  
Author(s):  
Maria Adina Vulcan ◽  
Celina Damian ◽  
Paul Octavian Stanescu ◽  
Eugeniu Vasile ◽  
Razvan Petre ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Scanning Electron Microscopy ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

This paper deals with the synthesis of polyurea and its use as polymer matrix for nanocomposites reinforced with multi-walled carbon nanotubes (MWCNT). Two types of materials were obtained during this research, the first cathegory uses the polyurea as matrix and the second one uses a mixture between epoxy resin and polyurea. The nanocomposites were characterized by Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM) and Tensile Tests .The elastomeric features of nanocomposites were highlighted by the results which showed low value of Tg. Also higher thermal stability with ~40oC compared with commercial products (M20) were observed, but lower mechanical properties compared to neat polyurea.

scholarly journals INFLUENCE OF FUNCTIONALIZED MULTI-WALLED CARBON NANOTUBES ON FILTERABILITY AND MECHANICAL PROPERTIES OF RAYON NANOCOMPOSITE FILAMENTS

2016 ◽  
Vol 3 (01) ◽  
Author(s):  
Holia Onggo ◽  
Rike Yudianti ◽  
Endang Ruchiat
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electron Microscope ◽  
Carbon Nanotube ◽  
Carbon Nanotube Dispersion ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Nanotube Dispersion ◽  
Scanning Electron

Carbon nanotube-rayon composite filaments was fabricated by spinning and coagulation of the mixture of 100mL functionalized carbon nanotube dispersion (containing 0.72 g FCNT) and cellulose xanthate in NaOH solution using viscose process. In the process, CNT was functionalized using mixture of acidic solution ( H2SO4/HNO3, 3:1 v/v). Influence of functionalized (FCNT) and non-functionalized carbon nanotubes (nFCNT) on the fabrication of rayon nanocomposite filament was studied. Physical and morphological properties of the nanocomposite filaments were characterized by single filament tenacity tester, photo micrograph, scanning electron microscope (SEM) and transmission electron microscope (TEM). Filterability and mechanical properties of FCNT-rayon nanocomposite filament greatly improved by reducing clogging constant from 1689 to 153 and increasing tenacity from 2.72 to 3.01 g/denier and decreasing elongation from 57.1 to 36.5% respectively compared with those of nFCNT-rayon nanocomposite filament.Keywords: functionalized multi-walled carbon nanotubes, nanocomposite filament, mechanical properties, filterability, dispersion  ABSTRAKRayon nanocomposite filaments telah dibuat melalui proses pemilinan (spinning) dan koagulasi (coagulation) dari campuran 100 mL larutan functionalized carbon nanotube dispersion (FCNT=0,72 g), selulosa santat dalam larutan NaOH melalui proses viskosa. CNT di functionalisasi (FCNT) menggunakan campuran larutan asam (H2SO4/HNO3, 3:1 v/v). Pengaruh fungsionalisasi CNT pada pembuatan rayon nanocomposite filaments dipelajari dengan cara membandingkannya dengan CNT tanpa fungsionalisasi (nFCNT). Sifat fisik dan morfologi dari rayon-nanocomposite filaments dikarakterisasi menggunakan tenacity tester, photo micrograph, scanning electron microscope (SEM) dan transmission electron microscope (TEM). Viskosa FCNT memiliki daya saring (Kw) cukup baik yaitu 155, sedangkan viskosa nFCNT  memiliki daya saring 1689 (tidak baik). Kekuatan mekanik dari FCNT-rayon nanocomposite filaments berturut turut adalah 3,01 g/denier (tenacity), dan 36,5% (elongation), lebih baik dibandingkan dengan nFCNT-rayon nanocomposite filament: 2,72 g/denier (tenacity) dan 57,1% (elongation).Kata kunci: fungsionalisasi multi-walled carbon nanotubes, rayon-nanocomposite filament, sifat mekanik, daya saring, dispersi

Morphology Analysis and Mechanical Properties of MWCNT Reinforced Nylon-6,6 Nanofiber Mats by Electrospun Method

2017 ◽  
Vol 267 ◽  
pp. 23-27 ◽  
Author(s):  
Fırat Durmuş ◽  
Mürsel Ekrem
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Static Loading ◽  
Tensile Tests ◽  
Sem Images ◽  
Nylon 6,6 ◽  
Multi Walled Carbon Nanotubes ◽  
Nanofiber Mats ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

In this study, the production of weight ratios of 1, 3 and 5 % multi-walled carbon nanotubes (MWCNT) reinforced / unreinforced Nylon 6,6 (N-6,6) nanofiber mats was carried out by electro spun method. Tensile strength (sT), modulus of elasticity (E), toughness and elongation amounts were investigated by tensile tests under static loading with / without reinforced nanofiber mats. % 3 MWCNT reinforced N-6,6 nanofiber mats, tensile strength, E and toughness increased by 84.4, 235 and 112 %, respectively, when compared with N-6,6 nanofiber mats. In addition, scanning electron microscope (SEM) images were also investigated to determine the physical properties at the specification of reinforced /unreinforced N-6,6 nanofiber mats.

Self-Assembly of Aligned Multi-Walled Carbon Nanotubes in Polypropylene-Coated Multi-Walled Carbon Nanotubes Composites

2013 ◽  
Vol 669 ◽  
pp. 55-62 ◽  
Author(s):  
Yi Na Xiong ◽  
Xiao Hua Chen ◽  
Qun Huang ◽  
Long Shan Xu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Scanning Electron Microscopy ◽  
Self Assembly ◽  
Butyl Methacrylate ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

Polypropylene (PP)-coated multi-walled carbon nanotubes (MWNTs) composite with MWNTs exceptional alignment dispersed and improved mechanical properties was prepared with maleic anhydride (MAH) as a compatibilizer and poly (butyl methacrylate) (PBMA) as a binding. Scanning electron microscopy (SEM) results showed that MWNTs within composite were aligned without aggregation and the oriented MWNTs were connected by matrix. High-resolution transmission electron microscopy (HRTEM) results demonstrated that the nanotubes were densely coated with a PP layer. Infrared spectroscopy (IR) results revealed that there was covalently linkage of MWNTs with PP via MAH. The interactions between MWNTs-PP and MWNTs-PBMA induced orientation of MWNTs. The improved mechanical properties of PP - coated MWNTs composite was also shown.

Functionalization effect on physico-mechanical properties of multi-walled carbon nanotubes/epoxy composites

2010 ◽  
Vol 22 (1) ◽  
pp. 48-59 ◽  
Author(s):  
Maria Wladyka-Przybylak ◽  
Dorota Wesolek ◽  
Weronika Gieparda ◽  
Anna Boczkowska ◽  
Ewelina Ciecierska
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Composites ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Preparation and Characterization of Polyesteramide Composited by Carbon Nanotube

2013 ◽  
Vol 562-565 ◽  
pp. 764-769
Author(s):  
Yi He ◽  
Lan Ma ◽  
Peng Hai ◽  
Jin Bo Li
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Carbon Nanotube ◽  
Tensile Testing ◽  
Elongation At Break ◽  
Multi Walled Carbon Nanotubes ◽  
In Suit ◽  
Walled Carbon Nanotubes

Polyesteramide (PEA) have good mechanical properties, compositing with multi-walled carbon nanotubes (MWNTs) can further improve the mechanical properties of the polymer. In this paper, PEA/MWNTs were synthesized in-suit using the reinforcement of nanocomposite. SEM and tensile testing were used to characterize the composited polyesteramides. The results show that MWNTs can be uniformly dispersed in the composited polyesteramides, the PEA/MWNTs tensile strength and Elongation at break increased.

Sign in / Sign up

Export Citation Format

Share Document