Characterization of Multiple Functional Solid Line of Graphite Ink Surface Printed by Micro-Flexographic

2015 ◽  
Vol 752-753 ◽  
pp. 1379-1383
Author(s):  
M.I. Maksud ◽  
Mohd Sallehuddin Yusof ◽  
Zaidi Embong
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Printing Plate ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Flexographic Printing ◽  
Scanning Electron

The purpose of this paper is to study a ink surface morphology, quantify the chemical composition involved in processing of graphite ink printed by flexographic printing. The methodology is to use surface sensitive technique, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) and Field Emission Scanning Electron Microscopy (FESEM). As a finding we successfully achieved 25 micron lines array using PDMS printing plate. The Originality and value of this work is surface sensitive techniques like XPS, AFM and FESEM were exclusively used in order to characterize graphite inks printed by flexographic method, using PDMS printing plate.

Wettability and Nanotribological Response of Silicon Surfaces Functionalized by Ion Implantation

2012 ◽  
Vol 730-732 ◽  
pp. 257-262
Author(s):  
Bruno Nunes ◽  
Sergio Magalhães ◽  
Nuno Franco ◽  
Eduardo Alves ◽  
Ana Paula Serro ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ion Implantation ◽  
Silicon Surfaces ◽  
Iron Ions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Scanning Electron

Aiming to improve the nanotribological response of Si-based materials we implanted silicon wafers with different fluences of iron ions (up to 2x1017 cm-2). Implantation was followed by annealing treatments at temperatures from 550°C to 1000°C. The implanted surfaces were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), atomic force microscopy (AFM) and wettability tests. Then, samples were submitted to AFM-based nanowear tests. We observe an increase of both hidrophobicity and and wear resistance of the implanted silicon, indicating that ion implantation of Si can be a route to be deeper explored in what concerns tribomechanical improvement of Si.

Grain Size Effect on Lattice of Ni Nanocrystals Prepared Through Polyol Method

2008 ◽  
Vol 8 (8) ◽  
pp. 4127-4131 ◽  
Author(s):  
G. S. Okram ◽  
Kh. Namrata Devi ◽  
H. Sanatombi ◽  
Ajay Soni ◽  
V. Ganesan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
Polyol Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Scanning Electron

Nanocrystalline nickel powders were prepared with grain size 'd' in the range 40–100 nm diameters through polyol method. X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used for characterization. XRD of the prepared samples consistently matched with standard fcc structure of nickel without any impurity peak. Detailed analysis and calculations using Scherrer equation for (111) peak revealed systematic increase in line width and peak shifting towards lower diffraction 2θ angles with decrease in nickel to ethylene glycol mole ratio. Different values of d estimated from various peaks of each sample suggested associated microstrains in the nanograins. Values of d estimated from X-ray diffraction patterns were compared with those obtained from atomic force microscopy and scanning electron microscopy results, and discussed. Observed lattice expansion is explained, on the basis of a theoretical model of linear elasticity.

Fabrication and Characterization of Polyaniline–ZnO Hybrid Nanocomposite Thin Films

2008 ◽  
Vol 8 (4) ◽  
pp. 1757-1761 ◽  
Author(s):  
Ajeet Kaushik ◽  
Jitendra Kumar ◽  
M. K. Tiwari ◽  
R. Khan ◽  
B. D. Malhotra ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Nanocomposite Thin Films ◽  
Scanning Electron

Polyaniline (PANI)–ZnO nanocomposite thin film has been successfully fabricated on glass substrates by using vacuum deposition technique. The as-grown PANI–ZnO nanocomposite thin films have been characterized using X-ray diffraction, Scanning Electron Microscopy, Atomic Force Microscopy, UV-visible spectrophotometer and Fourier Transform Infrared (FTIR) spectroscopy, respectively. X-ray diffraction of as-grown film shows the reflection of ZnO nanoparticles along with a broad peak of PANI. The surface morphology of nanocomposite films has been investigated using scanning electron microscopy and atomic force microscopy. The hypsochromic shift of the UV absorption band corresponding to π–π* transition in polymeric chain of PANI and a band at 504 cm –1 due to ZnO nanoparticles has been observed in the FTIR spectra. The hydrogen bonding between the imine group of PANI and ZnO nanoparticle has been confirmed from the presence of the absorbance band at 1151 cm–1 in the FTIR spectra of the nanocomposite thin films.

Sign in / Sign up

Export Citation Format

Share Document