Flexible Rolling Technology of Spring Steel 60Si2Mn

2014 ◽  
Vol 1037 ◽  
pp. 7-10
Author(s):  
Xin Guan ◽  
Zhong Qi Dong ◽  
Min Chen ◽  
Jian Lu Yuan ◽  
Jun Wei Fu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Spring Steel ◽  
Flexible Rolling ◽  
Rolling Technology

The mechanical properties of 60Si2Mn were investigated with the cooling rate changing under new finishing temperature. Results showed: the mechanical properties of 60Si2Mn plate depend on the finishing temperature and the cooling rate changing. The microstructure of ferrite and pearlitic lamellar is thinning, and sorbitic content and HV increase with the cooling rate increasing under the same finishing temperature.

Controlled Rolling and Cooling Process of Spring Steel 65Mn

2015 ◽  
Vol 713-715 ◽  
pp. 2624-2626
Author(s):  
Bing Wang ◽  
Dong Dong Liu ◽  
Zhong Qi Dong ◽  
Yang Song ◽  
Yan Jun Meng
Keyword(s):  
Mechanical Properties ◽  
Controlled Rolling ◽  
Spring Steel ◽  
Cooling Process ◽  
Rolling Technology

The mechanical properties and aging of 65Mn were investigated with the controlled rolling and cooling process of spring steel. The parameter of rolling technology was determined.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Effect of Si Content on Microstructure and Properties of 60Si2CrVA Spring Steel

2014 ◽  
Vol 968 ◽  
pp. 63-66 ◽  
Author(s):  
Fei Zhao ◽  
Zhan Ling Zhang ◽  
Jun Shuai Li ◽  
Cui Ye ◽  
Ni Li
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Testing Machine ◽  
Spring Steel ◽  
Impact Testing ◽  
X Ray ◽  
Comprehensive Properties ◽  
Spring Steels ◽  
Si Content

The microstructure and mechanical properties of the four spring steels with different Si content treated by Q-I-Q-T process were studied by metallographic microscope, MTS, impact testing machine and X-ray stress analyzer. The results show that the tensile strength and yield strength is first increased and then decreased with the increase of Si content, the volume fraction of retained austenite and elongation are fist decreased and then increased when the Si content is less than 2.1%, and the microstructure become finer and homogeneous. When Si content reaches 2.1%, the comprehensive properties of 60Si2CrVA spring steel is the best.

Microstructure and Properties of a Non-Quenched Prehardened Steel at Different Cooling Rate

2012 ◽  
Vol 524-527 ◽  
pp. 1976-1979
Author(s):  
Yi Luo ◽  
Jin Ming Peng
Keyword(s):  
Mechanical Properties ◽  
Fine Structure ◽  
Optical Microscopy ◽  
Cooling Rate ◽  
Retained Austenite ◽  
Transformation Products ◽  
Electronic Microscopy ◽  
Transmission Electronic Microscopy ◽  
Microstructure And Properties ◽  
Cooling Conditions

Mechanical properties of non-quenched prehardened (NQP) steel air cooled and sand cooled after forged were tested and their microstructure was investigated by optical microscopy and transmission electronic microscopy(TEM). The results show that mechanical properties of the NQP steel are similar at both cooling conditions, and their microstructure is bainite, whose fine structure is main bainite ferrite laths, retained austenite films, retained austenite islands and their transformation products. Bainite ferrite laths of the NQP steel air cooled are narrower than that sand cooled, while more retained austenite islands exist in latter.

Sign in / Sign up

Export Citation Format

Share Document