Effect of Pre-Heating Temperature on Microstructure and Properties of 22MnB5 Steel Hot Stamping

2014 ◽  
Vol 1063 ◽  
pp. 108-111
Author(s):  
Ping Li ◽  
Yu Sheng Liu ◽  
Tian Zong Gongzi ◽  
Ke Min Xue
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Martensitic Transformation ◽  
Heating Temperature ◽  
Hot Stamping ◽  
High Strength ◽  
High Tensile Strength ◽  
22Mnb5 Steel ◽  
Stamping Process ◽  
Ultra High Strength Steel

The hot stamping process of ultra high strength steel(UHSS) sheet is an innovative way to manufacture the components with a ultra high tensile strength. The sufficiency of martensitic transformation in formed component is affected by pre-heating temperature of blank directly. In this paper, experiments of heating UHSS blanks to 700°C, 800°C, 900°C and 1000°C were implemented to investigate the effect of pre-heating temperature on the formed component’s microstructure and mechanical properties. The results indicate that 900°C is the best pre-heating temperature for hot stamping process. The microstructure of formed component is all fine and uniform martensite. Meanwhile, tensile strength and vickers hardness raise up to 1580MPa and 450HV, respectively.

Effect of Dies Temperature on Mechanical Properties of Hot Stamping Square-Cup Part for Ultra High Strength Steel

2010 ◽  
Vol 129-131 ◽  
pp. 390-394
Author(s):  
Cheng Xi Lei ◽  
Zhong Wen Xing ◽  
Hong Ya Fu
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Hot Stamping ◽  
High Strength ◽  
Hot Forming ◽  
Forming Process ◽  
Stamping Process ◽  
Ultra High Strength Steel ◽  
Mechanical Properties Testing ◽  
Simulation Results

The numerical simulation of hot-stamping process was carried out for UHSS square-cup parts, and the influence of dies temperature on the hot-stamping process was anlysised. Besides, through the microstructure analysis and mechanical properties testing of the formed parts, effects of dies temperature on microstructures and mechanical properties of hot-stamping square-cup parts were obtained. The experiment and simulation results showed that the mechanical properties of the UHSS are strongly dependent on the temperature, so the dies temperature is one of the most important parameters that have to be taken into account in designing the hot-forming dies and the hot-forming process.

Hot Stamping Processing Experiments of Quenchable Boron Steel

2008 ◽  
Vol 575-578 ◽  
pp. 299-304 ◽  
Author(s):  
Jun Bao ◽  
Zhong Wen Xing ◽  
Yu Ying Yang
Keyword(s):  
Heating Temperature ◽  
Hot Stamping ◽  
Cooling Water ◽  
High Strength ◽  
Processing Parameters ◽  
Boron Steel ◽  
Complicated Shape ◽  
Water Flow Velocity ◽  
Ultra High Strength Steel ◽  
Automotive Parts

The quenchable boron steel is a novel type of ultra high strength steel used for automotive parts so as to reduce the weight of the whole automobile. The hot stamping processing experiments for bending parts were studied. The influence of the hot stamping processing parameters, such as the heating temperature, the heat holding time and the cooling water flow velocity, on the mechanics properties and microstructure of the hot stamping parts is obtained. And then the optimal ranges of these parameters are determined, which provides a basis for the control of the hot stamping process applied in complicated shape parts’ production.

Ultra-High Strength Steel Hot Stamping Technology and Devices

2014 ◽  
Vol 1063 ◽  
pp. 237-243
Author(s):  
Zhong De Shan ◽  
Qin Tai Yan ◽  
Chao Jiang ◽  
Wen Juan Rong
Keyword(s):  
Tensile Strength ◽  
High Strength Steel ◽  
Hot Stamping ◽  
Research Work ◽  
High Strength ◽  
Parameters Optimization ◽  
Systematic Research ◽  
China Academy ◽  
Ultra High Strength Steel ◽  
Vehicle Structure

Ultra High Strength Steel (UHSS) hot stamping technology is a special process which can enhance the steel tensile strength to 1500MPa. Appling this technology in producing vehicle structure parts can make car lighter and safer. In China there are more and more automobile enterprises adopt this technology. To master and extend the skill, China Academy of Machinery Science & Technology (CAM) have done systematic research, such as the strengthen mechanism of the steel, hot stamping key devices designing, forming and quenching integrated mould designing, stamping process parameters optimization, etc.. By now, CAM has mastered the mass production technology of vehicle parts, which can guarantee its shape and tensile strength, and produced such typical parts as door-beam, B pillar, etc.. The paper is an introduction of the research work and achievement about UHSS hot stamping developed by CAM.

Hybrid quenching method of hot stamping for automotive tubular beams

2015 ◽  
Vol 231 (9) ◽  
pp. 1599-1610 ◽  
Author(s):  
Jong-Kyu Park ◽  
Yang-Su Kim ◽  
Chang Hee Suh ◽  
Young-Suk Kim
Keyword(s):  
High Strength Steel ◽  
Hot Stamping ◽  
High Strength ◽  
Torsion Beam ◽  
Stamping Process ◽  
Die Quenching ◽  
Ultra High Strength Steel ◽  
Quenching Method ◽  
Torsion Beam Axle ◽  
Beam Axle

Recently, tubular-type coupled torsion beam axle, which is a component of the automotive rear suspension systems, has been developed by using ultra-high strength steel. It is manufactured by hot stamping process to enhance the strength and reduce springback. The hot stamping process is classified as a direct method and an indirect method according to forming sequence and quenching method, so-called die quenching or water quenching. Each of these methods has limitations in the aspect of dimensional accuracy and strength. Hybrid quenching is a new quenching method which sprays water to the tube directly in addition to die quenching. In this study, direct hot stamping with hybrid quenching was applied to produce an automotive tubular coupled torsion beam axle of ultra-high strength steel. This study proposes a simulation method of hybrid quenching for tubular beam and the hybrid quenching method was evaluated experimentally. Finally, the proposed hybrid quenching method has been found very effective in reducing the cooling time and thermal deformation.

Production and Use of the Textile Reinforced Concrete

2014 ◽  
Vol 982 ◽  
pp. 59-62 ◽  
Author(s):  
Filip Vogel
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
High Strength ◽  
Cement Matrix ◽  
High Tensile Strength ◽  
Textile Reinforced Concrete ◽  
Corrosion Resistant ◽  
New Material ◽  
Ductile Behavior

This article discusses about the textile reinforced concrete. The textile reinforced concrete is a new material with great possibilities for modern construction. The textile reinforced concrete consists of cement matrix and textile reinforcement of high strength fibers. This combination of cement matrix and textile reinforcement is an innovative combination of materials for use in the construction. The main advantage of the textile reinforced concrete is a high tensile strength and ductile behavior. The textile reinforced concrete is corrosion resistant. With these mechanical properties can be used textile reinforced concrete in modern construction.

scholarly journals Research on Lightweight Design and Indirect Hot Stamping Process of the New Ultra-High Strength Steel Seat Bracket

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 833 ◽  
Author(s):  
Tang ◽  
Gu ◽  
Jia ◽  
Li ◽  
Zhu ◽  
...  
Keyword(s):  
Topology Optimization ◽  
High Strength Steel ◽  
Lightweight Design ◽  
Hot Stamping ◽  
High Strength ◽  
Variable Density ◽  
Stamping Process ◽  
Electric Bus ◽  
Ultra High Strength Steel ◽  
New Type

Aiming at the need for lightweight requirements of the electric bus components, combined with the performance advantages of the hot stamping ultra-high strength steel, a new type of seat bracket structure is proposed. The new structure was analyzed by finite element method and the variable density topology optimization results. Subsequently, the new seat bracket was manufactured by the indirect hot stamping process. The results showed that the new type of seat bracket can reduce the weight by 17.04% after topology optimization, which achieved the goal of lightweight design of the structure. After indirect hot stamping, the bottom of the seat bracket microstructures were mainly martensite and the ultimate tensile strength was about 1560 MPa, the microhardness was equally distributed at about 513.5 HV. Finally, according to the stiffness check test, the seat bracket satisfied the user requirements.

Sign in / Sign up

Export Citation Format

Share Document