Model of Water-Air Two-Phase Flow in Saturated-Unsaturated Soil

2011 ◽  
Vol 308-310 ◽  
pp. 553-558
Author(s):  
Chun Hui Fang ◽  
Xiao Yue Zhang
Keyword(s):  
Mass Transfer ◽  
Numerical Model ◽  
Capillary Pressure ◽  
Water Flow ◽  
Unsaturated Soil ◽  
Calculation Method ◽  
Two Phase Flow ◽  
Air Flow ◽  
Phase Flow ◽  
Two Phase

For seepage in unsaturated soil, there are both air flow and water flow, which can be called the water-air two-phase flow. In order to simulate the water-air two-phase flow in soil when there is groundwater, a numerical model of water-air two-phase flow in saturated-unsaturated soil is established in this paper. By the model, the air-flow and water-flow in unsaturated soil are both considered in seepage calculation. And the mass transfer between air-phase and water-phase, change of phase states are considered in calculation. Capillary pressure is the most important factor for the water-air two-phase flow in unsaturated soil, and the calculation method of capillary pressure is also given in the paper. At last examples are given to verify the correctness of the numerical model and the calculation method.

Development of Air/Water Two-Phase Flow Centrifugal Pump and Its Operating Characteristics

2003 ◽  
Author(s):  
Akinori Furukawa ◽  
Satoshi Ohshita ◽  
Kusuo Okuma ◽  
Satoshi Watanabe
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Air Flow ◽  
Water Flow Rate ◽  
Phase Flow ◽  
Air Flow Rate ◽  
Operating Characteristics ◽  
Two Phase ◽  
Flow Pump

A centrifugal impeller, the pumping action of which could be highly kept even at an air-water two-phase flow condition of inlet void fraction more than 30% in the region of relatively high water flow rate, has been developed. In the present paper, the design concept of two-phase flow impeller is described, at first, with experimental results. The short bladed forward impeller with high outlet blade angle was decided to keep theoretical head higher even in two-phase flow condition and to disperse the air accumulating region on the suction blade surface by the water jet flow coming from the pressure side. Furthermore, the tandem arrangement of outer and inner rotating cascades with the same blade numbers was adopted to suppress the rotating stall phenomena appearing in the case of a single stage of outer cascade. It should be noted that these results were obtained with operating a boost pump installed upstream of mixing section of air and water, that is not an actual operation of two-phase flow pump. Secondly, the operating characteristics of this two-phase flow pump with change of air flow rate were investigated experimentally without operating the boost pump. As the trajectory of operating point with increasing air flow rate appears along the resistance curve of piping system, the impossibility of pumping occurs at lower air flow rate even though pump head takes a positive value at high air flow rate with increasing water flow rate. It is recognized that it is necessary to improve two-phase flow head characteristic curves in the region of low water flow rate to operate in wider two-phase flow conditions.

Experimental Investigation on Two-Phase Flow Distribution in Multi-Channel Manifold With Two Radial Inlets

2009 ◽  
Author(s):  
Liping Pang ◽  
Baomin Sun ◽  
Bo Wang
Keyword(s):  
Experimental Investigation ◽  
Water Flow ◽  
Significant Variation ◽  
Two Phase Flow ◽  
Air Flow ◽  
Flow Distribution ◽  
Phase Flow ◽  
Two Phase ◽  
Parallel Channels ◽  
Inlet Conditions

An experimental investigation was conducted to study the two-phase flow distributions in a horizontal cylindrical manifold with two radial inlets and 11 parallel channels. The effects of the different inlet conditions on two-phase flow distribution of parallel channels in the manifold were investigated. The flow rates of air and water in 11 channels were measured under symmetrical and unsymmetrical inlet conditions. Experimental results show that the air and water flow distributions of manifold at channels keep a stable flow ratio when two radial inlet conditions keep symmetrical. Water flow distribution has a significant variation and air flow distribution has a small change when two radial inlet conditions keep unsymmetrical and water superficial velocity increases at right inlet. Water and air flow distribution has a significant variation when two radial inlet conditions keep unsymmetrical and air superficial velocity decreases.

scholarly journals Two-Phase Flow Mass Transfer Analysis of Airlift Pump for Aquaculture Applications

Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 226
Author(s):  
Rashal Abed ◽  
Mohamed M. Hussein ◽  
Wael H. Ahmed ◽  
Sherif Abdou
Keyword(s):  
Mass Transfer ◽  
Oxygen Transfer ◽  
Transfer Rate ◽  
Two Phase Flow ◽  
Oxygen Transfer Rate ◽  
Flow Patterns ◽  
Oxygen Mass Transfer ◽  
Phase Flow ◽  
Two Phase ◽  
Airlift Pump

Airlift pumps can be used in the aquaculture industry to provide aeration while concurrently moving water utilizing the dynamics of two-phase flow in the pump riser. The oxygen mass transfer that occurs from the injected compressed air to the water in the aquaculture systems can be experimentally investigated to determine the pump aeration capabilities. The objective of this study is to evaluate the effects of various airflow rates as well as the injection methods on the oxygen transfer rate within a dual injector airlift pump system. Experiments were conducted using an airlift pump connected to a vertical pump riser within a recirculating system. Both two-phase flow patterns and the void fraction measurements were used to evaluate the dissolved oxygen mass transfer mechanism through the airlift pump. A dissolved oxygen (DO) sensor was used to determine the DO levels within the airlift pumping system at different operating conditions required by the pump. Flow visualization imaging and particle image velocimetry (PIV) measurements were performed in order to better understand the effects of the two-phase flow patterns on the aeration performance. It was found that the radial injection method reached the saturation point faster at lower airflow rates, whereas the axial method performed better as the airflow rates were increased. The standard oxygen transfer rate (SOTR) and standard aeration efficiency (SAE) were calculated and were found to strongly depend on the injection method as well as the two-phase flow patterns in the pump riser.

Modeling Two-Phase Flow in Porous Media Including Fluid-Fluid Interfacial Area

2008 ◽  
Author(s):  
Jennifer Niessner ◽  
S. Majid Hassanizadeh ◽  
Dustin Crandall
Keyword(s):  
Porous Media ◽  
Capillary Pressure ◽  
Two Phase Flow ◽  
Interfacial Area ◽  
Flow In Porous Media ◽  
Extended Model ◽  
Phase Flow ◽  
Two Phase ◽  
Specific Interfacial Area ◽  
Macro Scale

We present a new numerical model for macro-scale two-phase flow in porous media which is based on a physically consistent theory of multi-phase flow. The standard approach for modeling the flow of two fluid phases in a porous medium consists of a continuity equation for each phase, an extended form of Darcy’s law as well as constitutive relationships for relative permeability and capillary pressure. This approach is known to have a number of important shortcomings and, in particular, it does not account for the presence and role of fluid–fluid interfaces. An alternative is to use an extended model which is founded on thermodynamic principles and is physically consistent. In addition to the standard equations, the model uses a balance equation for specific interfacial area. The constitutive relationship for capillary pressure involves not only saturation, but also specific interfacial area. We show how parameters can be obtained for the alternative model using experimental data from a new kind of flow cell and present results of a numerical modeling study.

Numerical Investigation of Two-Phase Flow Over Unglazed Plate Collector Covered With Porous Material of Wire Screen for Solar Water Heater Application

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
T. Salameh ◽  
Y. Zurigat ◽  
A. Badran ◽  
C. Ghenai ◽  
M. El Haj Assad ◽  
...  
Keyword(s):  
Surface Tension ◽  
Porous Material ◽  
Water Flow ◽  
Two Phase Flow ◽  
Volume Fraction ◽  
Phase Flow ◽  
Two Phase ◽  
Solar Water ◽  
Wire Screen ◽  
Effect Of Surface

This paper presents three-dimensional numerical simulation results of the effect of surface tension on two-phase flow over unglazed collector covered with a wire screen. The homogenous model is used to simulate the flow with and without the effect of porous material of wire screen and surface tension. The Eulerian-Eulerian multiphase flow approach was used in this study. The phases are completely stratified, the interphase is well defined (free surface flow), and interphase transfer rate is very large. The liquid–solid interface, gas–liquid interface, and the volume fraction for both phases were considered as boundaries for this model. The results show that the use of porous material of wire screen will reduce the velocity of water flow and help the water flow to distribute evenly over unglazed plate collector. The possibility of forming any hot spot region on the surface was reduced. The water velocity with the effect of surface tension was found higher than the one without this effect, due to the extra momentum source added by surface tension in longitudinal direction. The use of porous material of wires assures an evenly distribution flow velocity over the inclined plate, therefore helps a net enhancement of heat transfer mechanism for unglazed solar water collector application.

Sign in / Sign up

Export Citation Format

Share Document