Experimental Investigation on the Effect of PM10 Removal by Charged Fine Mist

2012 ◽  
Vol 518-523 ◽  
pp. 3015-3019
Author(s):  
Liang Ze Zhi ◽  
Jun Feng Wang ◽  
Feng Gu ◽  
Zong Hai Zhang
Keyword(s):  
Experimental Investigation ◽  
Particle Size ◽  
Particulate Matter ◽  
Particle Size Distribution ◽  
Convenient Method ◽  
Aerosol Particles ◽  
Solid Particles ◽  
Outdoor Environment ◽  
Micron Size

In order to study the effect of the dust（PM10） removal in the outdoor environment by the charged fine mist, the adsorption characteristics of the charged fine mist on the aerosol particles was considered. This paper reports an experimental investigation of the phenomena which occur when charged fine mist was jetted into the aerosol laden space. The results presents evidence to show that the charged fine mist is an efficient and convenient method of gathering the particulate matter, especially for sub-micron size solid particles. The more narrow the particle size distribution is, the better the effect of the removal of fine solid particles becomes. This study showed that the charged fine mist can greatly reduced particulate matter in the outdoor environment, which could improve the quality of environment significantly.

Characterization of the emission behavior of pulse-jet cleaned filters using a low-cost particulate matter sensor/Charakterisierung der Emission von druckstoßgereinigten Oberflächenfiltern mit einem Low-Cost-Feinstaubsensor

Gefahrstoffe ◽  
2019 ◽  
Vol 79 (11-12) ◽  
pp. 443-450
Author(s):  
P. Bächler ◽  
J. Meyer ◽  
A. Dittler
Keyword(s):  
Particle Size ◽  
Particulate Matter ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Low Cost ◽  
Particle Emission ◽  
Filter Medium ◽  
Emission Measurement ◽  
Pm2.5 Concentration ◽  
Pulse Jet

The reduction of fine dust emissions with pulse-jet cleaned filters plays an important role in industrial gas cleaning to meet emission standards and protect the environment. The dust emission of technical facilities is typically measured “end of pipe”, so that no information about the local emission contribution of individual filter elements exists. Cheap and compact low-cost sensors for the detection of particulate matter (PM) concentrations, which have been prominently applied for immission monitoring in recent years have the potential for emission measurement of filters to improve process monitoring. This publication discusses the suitability of a low-cost PM-sensor, the model SPS30 from the manufacturer Sensirion, in terms of the potential for particle emission measurement of surface filters in a filter test rig based on DIN ISO 11057. A Promo® 2000 in combination with a Welas® 2100 sensor serves as the optical reference device for the evaluation of the detected PM2.5 concentration and particle size distribution of the emission measured by the low-cost sensor. The Sensirion sensor shows qualitatively similar results of the detected PM2.5 emission as the low-cost sensor SDS011 from the manufacturer Nova Fitness, which was investigated by Schwarz et al. in a former study. The typical emission peak after jet-pulse cleaning of the filter, due to the penetration of particles through the filter medium, is detected during Δp-controlled operation. The particle size distribution calculated from the size resolved number concentrations of the low-cost sensor yields a distinct distribution for three different employed filter media and qualitatively fits the size distribution detected by the Palas® reference. The emission of these three different types of filter media can be distinguished clearly by the measured PM2.5 concentration and the emitted mass per cycle and filter area, demonstrating the potential for PM emission monitoring by the low-cost PM-sensor. During the period of Δt-controlled filter aging, a decreasing emission, caused by an increasing amount of stored particles in the filter medium, is detected. Due to the reduced particle emission after filter aging, the specified maximum concentration of the low-cost sensor is not exceeded so that coincidence is unlikely to affect the measurement results of the sensor for all but the very first stage of filter life.

scholarly journals Particle Size Distribution of E-Cigarette Aerosols and the Relationship to Cambridge Filter Pad Collection Efficiency

2015 ◽  
Vol 26 (4) ◽  
Author(s):  
Steven L. Alderman ◽  
Chen Song ◽  
Serban C. Moldoveanu ◽  
Stephen K. Cole
Keyword(s):  
Particle Size ◽  
Particulate Matter ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Propylene Glycol ◽  
Collection Efficiency ◽  
Transmission Measurement ◽  
Average Particle ◽  
Electrical Mobility ◽  
Total Particulate Matter

AbstractThe relatively volatile nature of the particulate matter fraction of e-cigarette aerosols presents an experimental challenge with regard to particle size distribution measure-ments. This is particularly true for instruments requiring a high degree of aerosol dilution. This was illustrated in a previous study, where average particle diameters in the 10-50 nm range were determined by a high-dilution, electrical mobility method. Total particulate matter (TPM) masses calculated based on those diameters were orders of magnitude smaller than gravimetrically determined TPM. This discrepancy was believed to result from almost complete particle evaporation at the dilution levels of the electrical mobility analysis. The same study described a spectral transmission measurement of e-cigarette particle size in an undiluted state, and reported particles from 210-380 nm count median diameter. Observed particle number concentrations were in the 10Described here is a study in which e-cigarette aerosols were collected on Cambridge filters with adsorbent traps placed downstream in an effort to capture any material passing through the filter. Amounts of glycerin, propylene glycol, nicotine, and water were quantified on the filter and downstream trap. Glycerin, propylene glycol, and nicotine were effciently captured (> 98%) by the upstream Cambridge filter, and a correlation was observed between filtration efficiency and the partial vapor pressure of each component. The present analysis was largely inconclusive with regard to filter efficiency and particle-vapor partitioning of water. [Beitr. Tabakforsch. Int. 26 (2014) 183-190]

The Quality of U100 Sampling

1986 ◽  
Vol 2 (1) ◽  
pp. 419-423
Author(s):  
I. L. Whyte
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
General Purpose ◽  
Volume Changes ◽  
Sample Quality ◽  
Class 1 ◽  
Sample Disturbance

AbstractThe origins and development of the U100 (U4) thick-walled open-drive sampler are reviewed. The requirements of CP 2001 and BS 5930 are examined in relation to sample quality, and these are shown to be too favourable. Causes of sample disturbance are considered, particularly those due to volume changes, and shown to depend on moisture content, plasticity and particle size distribution. Quality classes possible with conventional U100 samples are suggested, and Classes 3 or 4 are to be generally expected. Class 1 samples are improbable. It is recommended that a general purpose sampler such as the U100 should have a maximum inside clearance of 1% and not ‘about 1%’ as recommended in BS 5930.

scholarly journals Factors determining the most efficient spray distribution for marine cloud brightening

2014 ◽  
Vol 372 (2031) ◽  
pp. 20140056 ◽  
Author(s):  
P. J. Connolly ◽  
G. B. McFiggans ◽  
R. Wood ◽  
A. Tsiamis
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Energy Efficient ◽  
Aerosol Particles ◽  
Care Needs ◽  
Salt Particle ◽  
Aerosol Particle Size ◽  
Spray Distribution ◽  
Added Salt

We investigate the sensitivity of marine cloud brightening to the properties of the added salt particle distribution using a cloud parcel model, with an aim to address the question of, ‘what is the most efficient particle size distribution that will produce a desired cooling effect?’ We examine the effect that altering the aerosol particle size distribution has on the activation and growth of drops, i.e. the Twomey effect alone, and do not consider macrophysical cloud responses that may enhance or mitigate the Twomey effect. For all four spray generation methods considered, Rayleigh jet ; Taylor cone jet ; supercritical fluid ; and effervescent spray , salt particles within the median dry diameter range D m =30–100 nm are the most effective range of sizes. The Rayleigh jet method is also the most energy efficient overall. We also find that care needs to be taken when using droplet activation parametrizations: for the concentrations considered, Aitken particles do not result in a decrease in the total albedo, as was found in a recent study, and such findings are likely to be a result of the parametrizations' inability to simulate the effect of swollen aerosol particles. Our findings suggest that interstitial aerosol particles play a role in controlling the albedo rather than just the activated cloud drops, which is an effect that the parametrization methods do not consider.

Effect of the particulate morphology of resin on the gelation process of PVC plastisols

2017 ◽  
Vol 37 (8) ◽  
pp. 757-764 ◽  
Author(s):  
Yubi Ji ◽  
Zhao Yang ◽  
Min Shi ◽  
Hong Tan
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Key Factors ◽  
Factors Affecting ◽  
Gelation Process ◽  
Secondary Particles ◽  
Poly Vinyl Chloride ◽  
Opposite Behavior

Abstract The gelation process of poly(vinyl chloride) (PVC) plastisol is very important to ensure the quality of the product and is affected by the type of resins, plasticizers, and other additives. In this study, the gelation process of the as-prepared PVC plastisol was characterized by measuring the evolution of vibrational viscosity with temperature or time using a vibrational viscometer. Furthermore, the effect of some commercial resins with different particulate morphologies on the gelation process was investigated by synchronously combining scanning election microscopy and laser particle size analyses. The results of this study proved that the particle size distribution and the aggregation degree of the secondary particles of a resin are the key factors affecting the gelation process. For the resin with bimodal particle size distribution, the closer the aggregation of the secondary particles, the slower the gel speed; however, an opposite behavior was observed for the resins with unimodal particle size distribution.

Sign in / Sign up

Export Citation Format

Share Document