Numerical Simulation of Dynamic Emergency Rescue and Regularities during Mine Fire Period

2012 ◽  
Vol 619 ◽  
pp. 336-341
Author(s):  
Zhong An Jiang ◽  
Wang Yi
Keyword(s):  
Numerical Simulation ◽  
Ventilation System ◽  
Junction Temperature ◽  
Buoyancy Effect ◽  
Gis Technology ◽  
Emergency Rescue ◽  
Mine Fire ◽  
Smoke Pollution ◽  
Pollution Area ◽  
Selection Of

Under the comprehensive consideration of “buoyancy effect” and “throttle effect” during mine fire period, the article used the geographic information system (GIS) technology, simulated the smoke pollution area, ventilation system junction temperature and state of airflow during mine fire period. Finishing a program for dynamic simulation of emergency rescue during mine fire period, which is significant for establishing fire pre-scheme and the decision-making during fire period. At the same time, the dynamic characteristic of ventilation system and selection of escaping route is also considered, which provides foundation for the rescuing the workers underground in time.

NUMERICAL SIMULATION OF VENTILATION SYSTEM WITHIN AN ARMORED VEHICLE CABIN

2007 ◽  
Vol 14 (2) ◽  
pp. 201-223
Author(s):  
Chin-Lung Chang ◽  
Chang-Hsien Tai ◽  
Chien-Hsiung Tsai ◽  
Yu-Ren Wang ◽  
Qing-Shan Hon
Keyword(s):  
Numerical Simulation ◽  
Ventilation System ◽  
Vehicle Cabin ◽  
Armored Vehicle

Effect Analysis of Nitrogen Injection on the Variation of “Oxidation Zone” in Coal Mine Gob Based on Numerical Simulation

2016 ◽  
Vol 9 (1) ◽  
pp. 47-54
Author(s):  
Jing Shen ◽  
Mingran Chang
Keyword(s):  
Numerical Simulation ◽  
Coal Mine ◽  
Heat Dissipation ◽  
Spontaneous Combustion ◽  
Oxidation Zone ◽  
Effect Analysis ◽  
Mine Fire ◽  
Nitrogen Injection ◽  
The Difference ◽  
Residual Coal

One of the main reasons for coal mine fire is spontaneous combustion of residual coal in gob. As the difference of compaction degree of coal and rock, the underground gob can be considered as a porous medium and divided into “three zones” in accordance with the criteria. The “three zones” are “heat dissipation zone”, “oxidation zone” and “choking zone”, respectively. Temperature programming experiments are taken and numerical simulation with obtained experimental data is utilized to analyze the distribution of “three zones” in this paper. Different width and depth of “oxidation zone” are obtained when the inlet air velocity is changed. As the nitrogen injection has inhibition effect on spontaneous combustion of residual coal in gob, nitrogen is injected into the gob. The widths of “oxidation zone” are compared before and after nitrogen injection. And ultimately the optimum location and volume of nitrogen injection are found out.

Numerical simulation studies of Cs3Bi2I9 perovskite solar device with optimal selection of electron and hole transport layers

Optik ◽  
2021 ◽  
Vol 231 ◽  
pp. 166417 ◽  
Author(s):  
Md Tohidul Islam ◽  
Md Rafsun Jani ◽  
Kazi Md Shorowordi ◽  
Zameer Hoque ◽  
Ali Mucteba Gokcek ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Hole Transport ◽  
Optimal Selection ◽  
Simulation Studies ◽  
Hole Transport Layers ◽  
Selection Of

scholarly journals Procedure for the Selection of Rubber Compound in Rubber-Metal Springs for Vibration Isolation

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1737
Author(s):  
Milan Banić ◽  
Dušan Stamenković ◽  
Aleksandar Miltenović ◽  
Dragan Jovanović ◽  
Milan Tica
Keyword(s):  
Numerical Simulation ◽  
Constitutive Model ◽  
Vibration Isolation ◽  
Correct Selection ◽  
Virtual Experiment ◽  
Rubber Compound ◽  
Key Factor ◽  
Railway Engineering ◽  
Selection Of

The selection of a rubber compound has a determining influence on the final characteristics of rubber-metal springs. Therefore, the correct selection of a rubber compound is a key factor for development of rubber-metal vibration isolation springs with required characteristics. The procedure for the selection of the rubber compound for vibration isolation of rubber-metal springs has been proposed, so that the rubber-metal elements have the necessary characteristics, especially in terms of deflection. The procedure is based on numerical simulation of spring deflection with Bergström-Boyce constitutive model in virtual experiment, with a goal to determine which parameters of the constitutive model will lead to spring required deflection. The procedure was verified by case study defined to select rubber compound for a rubber–metal spring used in railway engineering.

A Wall Base Ventilation System Applied at Different Wall Geometries—Numerical Simulation of the Evaporative Process

2012 ◽  
Vol 30 (1) ◽  
pp. 1-12 ◽  
Author(s):  
J. M. P. Q. Delgado ◽  
A. S. Guimarães ◽  
V. P. de Freitas
Keyword(s):  
Numerical Simulation ◽  
Ventilation System

Study on the Integrated Design of Underground Construction Lighting and Ventilation System

2011 ◽  
Vol 374-377 ◽  
pp. 702-705
Author(s):  
Wei Feng ◽  
Hui Min Li
Keyword(s):  
Numerical Simulation ◽  
Thermal Environment ◽  
Ventilation System ◽  
Integrated Design ◽  
Structure Design ◽  
Light Environment ◽  
System Model ◽  
Underground Construction ◽  
New Type

In the underground building, Light environment and thermal environment is poorer, in order to improve the problem, this paper brings forward a new type of lighting and ventilation system model; discusses the principle and characteristics of transmission; and analyses the question that influences lighting and ventilated effect in the application. Structure design and numerical simulation is the focus of the next step.

Flank Milling for Blisk with a Barrel Ball Milling Cutter

2009 ◽  
Vol 407-408 ◽  
pp. 202-206
Author(s):  
Tian Li ◽  
Wu Yi Chen ◽  
Ru Feng Xu ◽  
Dan Wang
Keyword(s):  
Numerical Simulation ◽  
Ball Milling ◽  
Strip Width ◽  
Flank Milling ◽  
Location Strategy ◽  
Milling Cutter ◽  
Machining Strip Width ◽  
Blisk Blade ◽  
Blade Machining ◽  
Selection Of

To satisfy the requirement in blisk machining, a barrel-ball milling (BBM) cutter suitable for machining both blade and hub is presented in this paper. The selection of cutter parameter and calculation of cutter location were put forward. The new efficient machining cutter location via the advanced optimization on cutter machining strip width was gained. By the numerical simulation of blisk blade machining, the feasibility of the BBM cutter and cutter location strategy were verified. The result showed that the efficiency of this method was increased to more than three times compared to the machining with a ball cutter.

Sign in / Sign up

Export Citation Format

Share Document