Structure Design of Transmissive Switch-Zoom Infrared Systems

2013 ◽  
Vol 712-715 ◽  
pp. 2169-2172
Author(s):  
Qing Lian Jia ◽  
Li Wei Song
Keyword(s):  
Optical Axis ◽  
Design Method ◽  
Optical Design ◽  
Structure Design ◽  
Radial Clearance ◽  
Zoom Lens ◽  
Alignment Method ◽  
Machine Experiment ◽  
Optical Structure ◽  
System Axis

A new optical structure design method was proposed by forward-object lens, zoom lens, focus lens and behind-object lens with transmissive switch-zoom infrared system. And an alignment method of the above structure was proposed to assure the imaging precision. The larger caliber forward lens structure was designed to immovably axial with system axis, while the zoom lens structure was designed to three different structures by actual optical design for reducing system dimension. The focus lens structure was absolute configuration for the stabilization during focus. The rear lens structure was also designed to small radial clearance. A through-shaft type tooling was proposed to cooperate to adjusting and confirming of the system optical axis by exact boring machine. Experiment results showed that the alignment method can be assured precision and economized cost.

scholarly journals Multi-Branch Cable Harness Layout Design Based on Genetic Algorithm with Probabilistic Roadmap Method

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Yingfeng Zhao ◽  
Jianhua Liu ◽  
Jiangtao Ma ◽  
Linlin Wu
Keyword(s):  
Genetic Algorithm ◽  
Topological Structure ◽  
Design Method ◽  
Route Planning ◽  
Layout Design ◽  
Structure Design ◽  
Prototype System ◽  
Cable Harness ◽  
Probabilistic Roadmap ◽  
Probabilistic Roadmap Method

AbstractCurrent studies on cable harness layouts have mainly focused on cable harness route planning. However, the topological structure of a cable harness is also extremely complex, and the branch structure of the cable harness can affect the route of the cable harness layout. The topological structure design of the cable harness is a key to such a layout. In this paper, a novel multi-branch cable harness layout design method is presented, which unites the probabilistic roadmap method (PRM) and the genetic algorithm. First, the engineering constraints of the cable harness layout are presented. An obstacle-based PRM used to construct non-interference and near to the surface roadmap is then described. In addition, a new genetic algorithm is proposed, and the algorithm structure of which is redesigned. In addition, the operation probability formula related to fitness is proposed to promote the efficiency of the branch structure design of the cable harness. A prototype system of a cable harness layout design was developed based on the method described in this study, and the method is applied to two scenarios to verify that a quality cable harness layout can be efficiently obtained using the proposed method. In summary, the cable harness layout design method described in this study can be used to quickly design a reasonable topological structure of a cable harness and to search for the corresponding routes of such a harness.

Based on the Grey Relation Analysis of Ecological Composite Wall Seismic Performance Research

2013 ◽  
Vol 368-370 ◽  
pp. 1043-1047
Author(s):  
Yin Zhang ◽  
You Han ◽  
Shuai Liang
Keyword(s):  
Seismic Performance ◽  
Evaluation System ◽  
Design Method ◽  
Structure Design ◽  
Grey System Theory ◽  
Frame Structure ◽  
Wall Structure ◽  
Width Ratio ◽  
Grey System ◽  
Composite Wall

Ecological composite wall as ecological composite wall structure of the main stress components, the seismic performance is ecological composite wall structure seismic performance evaluation system of the main content. Based on the grey system theory, the grey correlation analysis to the key parameters (the mouth of the cave, frame structure, height to width ratio) change ecological composite wall test results are analyzed, the key parameters on the ecological composite wall the influence law of seismic performance, for choosing wall structure design method to provide basis.

Modular Design Technology of Multi-DOF Mechanical Arm

2014 ◽  
Vol 599-601 ◽  
pp. 358-361
Author(s):  
Huan Qiang ◽  
Hu Zhang ◽  
Yan Zhou
Keyword(s):  
Modular Design ◽  
Design Method ◽  
Structure Design ◽  
Degree Of Freedom ◽  
Dynamics Simulation ◽  
Complicated Structure ◽  
Design Technology ◽  
Structure Line ◽  
Six Dof

A design method of modular joint is proposed according to the complicated structure, line exposed and heavier characteristics of multi-DOF (degree of freedom) mechanical arm. In this paper, the design of modular joint was carried on and a model of six-DOF mechanical arm was built through the research on the structure of mechanical arm. On this basis, dynamics simulation will be carried. The results show that the modular design method simplified the structure of the mechanical arm, the dynamics simulation proved it was feasible for the structure design and drive selection.

Optical design of the high-power zoom lens

2014 ◽  
Vol 21 (6) ◽  
pp. 745-751
Author(s):  
Daisuke Ito
Keyword(s):  
High Power ◽  
Optical Design ◽  
Zoom Lens

scholarly journals Off-Axis Diffractive Optics for Compact Terahertz Detection Setup

2020 ◽  
Vol 10 (23) ◽  
pp. 8594
Author(s):  
Paweł Komorowski ◽  
Mateusz Surma ◽  
Michał Walczakowski ◽  
Przemysław Zagrajek ◽  
Agnieszka Siemion
Keyword(s):  
3D Printing ◽  
Small Volume ◽  
Optical Element ◽  
Structure Design ◽  
Thz Radiation ◽  
Direct Printing ◽  
Terahertz Detection ◽  
3D Printed ◽  
Printing Techniques ◽  
Optical Structure

Medical and many other applications require small-volume setups enabling terahertz imaging. Therefore, we aim to develop a device for the in-reflection examination of the samples. Thus, in this article, we focus on the diffractive elements for efficient redirection and focusing of the THz radiation. A terahertz diffractive optical structure has been designed, optimized, manufactured (using extrusion-based 3D printing) and tested. Two manufacturing methods have been used—direct printing of the structures from PA12, and casting of the paraffin structures out of 3D-printed molds. Also, the limitations of the off-axis focusing have been discussed. To increase the efficiency, an iterative algorithm has been proposed that optimizes off-axis structures to focus the radiation into small focal spots located far from the optical axis, at an angle of more than 30 degrees. Moreover, the application of higher-order kinoform structure design allowed the maintaining of the smallest details of the manufactured optical element, using 3D printing techniques.

scholarly journals Design of a Hand-Launched Solar-Powered Unmanned Aerial Vehicle (UAV) System for Plateau

2020 ◽  
Vol 10 (4) ◽  
pp. 1300 ◽  
Author(s):  
Xin Zhao ◽  
Zhou Zhou ◽  
Xiaoping Zhu ◽  
An Guo
Keyword(s):  
Low Temperature ◽  
Conceptual Design ◽  
Unmanned Aerial Vehicle ◽  
Design Method ◽  
Structure Design ◽  
Control Law ◽  
Trajectory Tracking Control ◽  
Plateau Area ◽  
Aerial Vehicle ◽  
Solar Powered

This paper describes our work on a small, hand-launched, solar-powered unmanned aerial vehicle (UAV) suitable for low temperatures and high altitudes, which has the perpetual flight potential for conservation missions for rare animals in the plateau area in winter. Firstly, the conceptual design method of a small, solar-powered UAV based on energy balance is proposed, which is suitable for flight in high-altitude and low-temperature area. The solar irradiance model, which can reflect the geographical location and time, was used. Based on the low-temperature discharge test of the battery, a battery weight model considering the influence of low temperature on the battery performance was proposed. Secondly, this paper introduces the detailed design of solar UAV for plateau area, including layout design, structure design, load, and avionics. To increase the proportion of solar cells covered, the ailerons were removed and a rudder was used to control both roll and yaw. Then, the dynamics model of an aileron-free layout UAV was developed, and the differences in maneuverability and stability of aileron-free UAV in plateau and plain areas were analyzed. The control law and trajectory tracking control law were designed for the aileron-free UAV. Finally, the flight test was conducted in Qiangtang, Tibet, at an altitude of 4500 m, China’s first solar-powered UAV to take off and land above 4500 m on the plateau in winter (−30 °C). The test data showed the success of the scheme, validated the conceptual design method and the success of the control system for aileron-free UAV, and analyzed the feasibility of perpetual flight carrying different loads according to the flight energy consumption data.

scholarly journals Structure design and reliability analysis of Al-Ti lugs

2021 ◽  
Vol 39 (1) ◽  
pp. 1-8
Author(s):  
Yunwen Feng ◽  
Jiale Zhang ◽  
Xiaofeng Xue ◽  
Xiaoping Zhong ◽  
Wei Xie
Keyword(s):  
Reliability Analysis ◽  
Structural Design ◽  
Design Principle ◽  
Load Transfer ◽  
Design Method ◽  
Static Strength ◽  
Structure Design ◽  
Safety Design ◽  
Design Requirements ◽  
Metal Materials

Aircraft lug joint is the key part of load transfer. In order to improve the safety of lug joint, on the premise of meeting the design requirements of static strength and fatigue, the composite connection lug structure design technology of different metal materials is proposed in this paper. Firstly, the damage safety design and life reliability analysis of the lug structure are studied theoretically. Secondly, based on the concept of damage safety design and the design principle of deformation coordination, the design method of composite connection lug with deformation coordination is proposed, and the thickness ratio of single ear is 0.8:1:0.8. Finally, the reliability of the composite lug is analyzed. The results show that the structural design scheme of aluminum-titanium composite ear piece can meet the requirements of static strength and damage tolerance, and compared with the conventional ear structure, the failure probability of structure mission life is greatly reduced when the weight of the composite connection lug is only increased by 4.9%. The proposed method can effectively guide the structural design of composite ear piece.

scholarly journals DESIGN OF PERKUWEN BRIDGE PART WAY LONG IKIS-LAMBAKAN PASER TANA PASER REGENCY PROVINCE EAST KALIMANTAN

CERUCUK ◽  
2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Humaira Afrila ◽  
Markawie Markawie
Keyword(s):  
Design Method ◽  
Plate Thickness ◽  
Steel Structures ◽  
Structure Design ◽  
Steel Pipe ◽  
Pipe Pile ◽  
East Kalimantan ◽  
Composite Bridges ◽  
Composite Bridge ◽  
Steel Pipe Pile

Long Kali is a sub-district of Paser Tana Paser Regency Prov. East Kalimantan. In this sub-district have two village separate by a river, that is Perkuwen river, there is bridge has a broke. Whereas the village very needed a bridge because it is used as a transportation infrastructure for peoples and also passed by vehicles transporting oil palm yields . Therefore, the design of composite bridges made with spans 25 m and 7 m wide bridge.In this plan the analysis of Standard methods of loading refers to the bridge imposition For RSNI T-02-2005 about composite bridge structure design method, refers to RSNI T-03-2005 about Steel Structural Design For Bridge, SNI 03-1729-2002 about Steel Structures Planning Procedures and SNI 03-2847-2002 about Concrete Structures Calculation for Building.The result is used the main girder profile SH 950 x 400 x 16 x 32 and diaphragm WF 400 x 200 x 8 x 13. Vehicle floor plate thickness 20 cm using quality concrete  30 MPa and quality reinforcing steel reinforcement  360 MPa with subject dividers reinforcement D22- 100 and D12-100 mm. In using concrete pavement  30 MPa D22-100 mm staple reinforcement and shear reinforcement rebars quality D12-100 mm  360 MPa. Concrete abutment in the form  25 MPa at 2 m height and length of 8,5 m. Steel pipe pile foundations quality  25 MPa are 16 pieces with a length of 10 meters and a diameter of 0.4 m.Keyword: Bridge, composite, steel pipe pile.

Sign in / Sign up

Export Citation Format

Share Document