Comparison of Friction Stir and Tungsten Inert Gas Weldments of AA6061-T6

2013 ◽  
Vol 858 ◽  
pp. 19-23
Author(s):  
Mohd Rafiza Shaari ◽  
Zuhailawati Hussain ◽  
Indra Putra Almanar ◽  
Nguyen Van Thuong
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Fusion Zone ◽  
Aluminium Alloys ◽  
Inert Gas ◽  
Nugget Zone ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
And Tungsten

In this research, 6061-T6 aluminum alloys were welded using friction stir welding and tungsten inert as techniques in order to investigate the microstructure and mechanical properties. FSW of aluminium alloys has showed better mechanical properties compared to the conventional welding, tungsten inert gas (TIG). FSW weldment did not show any pores at the nugget zone compared to fusion zone in TIG weldment which produced a lot of pores.

scholarly journals Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1938
Author(s):  
Haifeng Yang ◽  
Hongyun Zhao ◽  
Xinxin Xu ◽  
Li Zhou ◽  
Huihui Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Weld Nugget ◽  
Al Alloy ◽  
Nugget Zone ◽  
T Joints ◽  
Friction Stir ◽  
Stationary Shoulder ◽  
Microstructure And Mechanical Properties

In this study, 2A14-T4 Al-alloy T-joints were prepared via stationary shoulder friction stir welding (SSFSW) technology where the stirring pin’s rotation speed was set as different values. In combination with the numerical simulation results, the macro-forming, microstructure, and mechanical properties of the joints under different welding conditions were analyzed. The results show that the thermal cycle curves in the SSFSW process are featured by a steep climb and slow decreasing variation trends. As the stirring pin’s rotation speed increased, the grooves on the weld surface became more obvious. The base and rib plates exhibit W- or N-shaped hardness distribution patterns. The hardness of the weld nugget zone (WNZ) was high but was lower than that of the base material. The second weld’s annealing effect contributed to the precipitation and coarsening of the precipitated phase in the first weld nugget zone (WNZ1). The hardness of the heat affect zone (HAZ) in the vicinity of the thermo-mechanically affected zone (TMAZ) dropped to the minimum. As the stirring pin's rotation speed increased, the tensile strengths of the base and rib plates first increased and then dropped. The base and rib plates exhibited ductile and brittle/ductile fracture patterns, respectively.

Evaluation of dissimilar joints properties of 5083-H12 and 6061-T6 aluminum alloys produced by tungsten inert gas and friction stir welding

2015 ◽  
Vol 231 (3) ◽  
pp. 297-308 ◽  
Author(s):  
Morteza Ghaffarpour ◽  
Mohammad Kazemi ◽  
Mohammad Javad Mohammadi Sefat ◽  
Ahmad Aziz ◽  
Kamran Dehghani
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Traverse Speed ◽  
Inert Gas ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys ◽  
The Difference ◽  
Welding Processes

In the present study, friction stir welding (FSW) and tungsten inert gas (TIG) techniques were used to join the dissimilar aluminum alloys of 5083-H12 and 6061-T6. The laboratory tests were designed using design of experiment (DOE) method. Variables for the FSW process were the rotational speed, traverse speed, shoulder diameter, and pin diameter. They changed in ranges of 700–2500 r/min, 25–400 mm/min, 10–14 mm, and 2–4 mm, respectively. In the case of TIG process, the variables were current intensity, traverse speed, and tilt angle. These parameters varied from 80 to 90 A, 200 to 400 mm/min, and 3° to 12°, respectively. The optimum amounts of parameters were obtained using response surface methodology (RSM). The RSM-based model was developed to predict ultimate tensile strength (UTS) of the welds produced. In FSW, the difference between predicted and measured UTS was about 1.28% and in TIG it was 1.78%. The good agreement between experimental and predicted results indicates the high accuracy of the developed model. Mechanical properties and also the microstructure of the welds were compared after optimizing both welding processes using RSM. The results showed that the welds produced by FSW indicated a considerably higher quality and also improved mechanical properties compared to TIG. Properties of the joints obtained by FSW in single-sided joints were more desirable. In the double-sided welds obtained by FSW these differences were of an even higher significance.

Study on the Microstructure and Mechanical Properties of Welding Joints of 7A05 Aluminum Alloy by FSW

2014 ◽  
Vol 496-500 ◽  
pp. 110-113
Author(s):  
Dong Gao Chen ◽  
Jin He Liu ◽  
Zhi Hua Ma ◽  
Wu Lin Yang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Speed ◽  
Welded Joint ◽  
Optical Microscope ◽  
Nugget Zone ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Welding Joints

The7A05 aluminum alloy of the 10mm thickness was welded by the friction stir welding. The microstructure and mechanical Properties of the welded joint was researched by the optical microscope, etc. The results showed: the microstructure of the weld nugget zone and the thermal mechanically affected zone were refined as the welding speed increasing when the rotate speed is constant. As the welding speed increasing the strength of extension of the welded joint is increasing at first and then stable basically. but the yield strength had no obvious change.

Microstructure and Mechanical Properties of Friction Stir Welded AA2195-T0

2016 ◽  
Vol 857 ◽  
pp. 266-270 ◽  
Author(s):  
Ho Sung Lee ◽  
Jong Hoon Yoon ◽  
Joon Tae Yoo ◽  
Kyung Ju Min
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Weld Zone ◽  
Microscopic Analysis ◽  
Butt Joint ◽  
Fusion Welding ◽  
Electron Microscopic ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties

Aluminum-copper-lithium alloy is a light weight metal that has been used as substitute for conventional aerospace aluminum alloys. With addition of Li element, it has lower density but higher strength. However these aluminum alloys are hard to weld by conventional fusion welding, since they often produce porosities and cracking in the weld zone. It is known that solid state welding like friction stir welding is appropriate for joining of this alloy. In this study, friction stir welding was performed on AA2195 sheets, in butt joint configuration in order to understand effects of process parameters on microstructure and mechanical properties in the weld zone. The results include the microstructural change after friction stir welding with electron microscopic analysis of precipitates.

Microstructure and Mechanical Properties of Cu-Cr-Zr Alloy by Friction Stir Welding

2012 ◽  
Vol 602-604 ◽  
pp. 608-611
Author(s):  
Di Qiu He ◽  
Rui Lin Lai ◽  
Shao Hua Xu ◽  
Kun Yu Yang ◽  
Shao Yong Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Base Material ◽  
Traverse Speed ◽  
Nugget Zone ◽  
Alloy Plate ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Zr Alloy

In this study, Cu-Cr-Zr alloy joints are successfully fabricated by friction stir welding (FSW). Defect-free weld are produced on 12mm thick Cu-Cr-Zr alloy plate useing a non-consumable tool with a specially designed and shoulder with a constant rotation speed and a fixed traverse speed. The effect of friction stir welding (FSW) on the microstructure and mechanical properties of Cu-Cr-Zr alloy joints are investigated in details: The joints showed the presence of various zones such as nugget zone (NZ) and thermo-mechanically affected zone (TMAZ) and base metal (BM), the microhardness and the tensile strength of welded joints are lower than that of the base material.

Sign in / Sign up

Export Citation Format

Share Document