Issue on Calibration of Direct Feed Biconical Antenna in a Semi-Anechoic Chamber Using Standard Antenna Method

2014 ◽  
Vol 903 ◽  
pp. 273-278 ◽  
Author(s):  
Syarfa' Zahirah Sapuan ◽  
Mohd Zarar Mohd Jenu ◽  
Alireza Kazemipour
Keyword(s):  
Electromagnetic Compatibility ◽  
Ground Plane ◽  
Anechoic Chamber ◽  
Space Environment ◽  
Frequency Range ◽  
Biconical Antenna ◽  
Measurement Results ◽  
Antenna Type ◽  
Antenna Factor ◽  
Antenna Calibration

Antenna calibration is crucial to ensure the accuracy of Electromagnetic Compatibility (EMC) measurement results. Standard Antenna Method (SAM) is one of the methods widely used in antenna calibration which requires reference antenna with known Antenna Factor (AF) in a free space environment. The work presented in this paper is on the calibration of the AF of a direct-feed biconical antenna in a semi-anechoic chamber (SAC) with considerations given to the effects of ground plane, antenna height, reference antenna type and effects of phase center. The frequency range for the analysis is from 200 MHz to 2 GHz. It is found that antenna located 1.5 m from ground provides the best result compared to modeling. In addition, the phase centers of the reference and test antenna must be at the same positions during the measurements.

Antenna Calibration Methods for Antenna Factor Measurements

2012 ◽  
Vol 2 (4) ◽  
pp. 43-59 ◽  
Author(s):  
L. Mescia ◽  
O. Losito ◽  
V. Castrovilla ◽  
P. Bia ◽  
F. Prudenzano
Keyword(s):  
Electromagnetic Interference ◽  
Electromagnetic Compatibility ◽  
Ground Plane ◽  
Empty Space ◽  
Horn Antenna ◽  
International Standards ◽  
Impedance Method ◽  
Calibration Methods ◽  
Antenna Impedance ◽  
Antenna Factor

In the fields of electromagnetic interference and electromagnetic compatibility, it is important to measure the strength of the electric field originating from electric devices. For this purpose, knowledge of the antenna factor of a receiving antenna is necessary. According to international standards, the accurate measurement of the antenna factor involves the use of calibration test sites characterized by very large sizes of both the ground plane and the empty space volume above it. As a consequence, these setup conditions make the antenna factor measurements quite expensive for the customer. In this paper, the authors discuss the well know antenna-based and site-based methods as well as recently measurement method called Antenna Impedance Method as able to obtain the free-space antenna factor. Moreover, the authors investigate on the suitability of semi-anechoic chamber for reliable antenna factor calibrations. In particular, the experimental measurements of the antenna factor obtained by using the antenna impedance method were compared with Standard Field Method and the data provided by the manufacturer of three antennas (Biconical, Log-periodic and Horn antenna) founding an agreement with the international standard ANSI C63.5-2006.

Emi antenna calibration on an absorber-lined ground plane to determine free-space antenna factor

2003 ◽  
Vol 45 (4) ◽  
pp. 656-660 ◽  
Author(s):  
Y. Matsumoto ◽  
T. Umeda ◽  
A. Nishikata ◽  
K. Fujii ◽  
Y. Yamanaka ◽  
...  
Keyword(s):  
Free Space ◽  
Ground Plane ◽  
Space Antenna ◽  
Antenna Factor ◽  
Antenna Calibration

Design of a compact UWB antenna with a partial ground plane on epoxy woven glass material

2017 ◽  
Vol 24 (1) ◽  
pp. 73-79
Author(s):  
Md. Moinul Islam ◽  
Mohammad Tariqul Islam ◽  
Mohammad Rashed Iqbal Faruque ◽  
Rabah W. Aldhaheri ◽  
Md. Samsuzzaman
Keyword(s):  
Dielectric Material ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Design Parameters ◽  
Uwb Antenna ◽  
Glass Material ◽  
Measurement Results ◽  
Good Term ◽  
Parametric Analyses ◽  
Uwb Applications

AbstractA compact ultra-wideband (UWB) antenna is presented in this paper with a partial ground plane on epoxy woven glass material. The study is discussed to comprehend the effects of various design parameters with explicit parametric analyses. The overall antenna dimension is 0.22×0.26×0.016 λ. A prototype is made on epoxide woven glass fabric dielectric material of 1.6 mm thickness. The measured results point out that the reported antenna belongs to a wide bandwidth comprehending from 3 GHz to more than 11 GHz with VSWR<2. It has a peak gain of 5.52 dBi, where 3.98 dBi is the average gain. Nearly omnidirectional radiation patterns are observed within the operating frequency bands. A good term exists between simulation and measurement results, which lead the reported antenna to be an appropriate candidate for UWB applications.

Gradient structures of Ni – Zn ferrites for electromagnetic radiation protection devices

2021 ◽  
Vol 5 ◽  
pp. 39-46
Author(s):  
V. V. Karanskij ◽  
◽  
S. V. Smirnov ◽  
A. S. Klimov ◽  
E. V. Savruk ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electromagnetic Radiation ◽  
Radiation Protection ◽  
Electromagnetic Compatibility ◽  
Protective Coatings ◽  
Frequency Range ◽  
Near Surface ◽  
Zn Ferrite ◽  
Absorbing Materials ◽  
Plasma Electronic

Increasing the reliability requirements for electromagnetic compatibility of electronic equipment requires the creation of protective coatings that absorb electromagnetic radiation or the development of new radio-absorbing materials. In the frequency range up to 1 GHz, radio-absorbing materials based on Ni – Zn ferrites are of the greatest interest. The absorption of electromagnetic radiation by ferrites occurs due to resonant phenomena at the level of domains and atoms. Improving the performance of ferrites is possible by modifying their surface properties. In this paper, gradient structures for electromagnetic radiation protection products are obtained by treating the surface of Ni – Zn ferrite samples with a low-energy electron beam. To generate the electron beam, a unique development was used — a forevacuum plasma electronic source that allows forming and transporting a beam with a power density of up to 105 W/cm2 under conditions of high pressure and high gas release. As a result of processing, gradient structures were found on the surface of ferrites. A theoretical analysis and experimental study of the obtained structures “non – magnetic conductor – ferrite”, characterized by an increased attenuation coefficient and a reduced reflection coefficient of electromagnetic radiation in the frequency range from 0.5 to 2.5 GHz. The possibility of obtaining near-surface layers depleted in zinc with increased electrical conductivity and reduced magnetic permeability is shown.

scholarly journals A Circular Disc Microstrip Antenna with Dual Notch Band for GSM/Bluetooth and Extended UWB Applications

2018 ◽  
Vol 7 (2.16) ◽  
pp. 11
Author(s):  
Sanjeev Kumar ◽  
Ravi Kumar ◽  
Rajesh Kumar Vishwakarma
Keyword(s):  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
Circular Disc ◽  
Ultra Wideband ◽  
Resonant Circuit ◽  
Frequency Range ◽  
Notch Band ◽  
Uwb Applications ◽  
Ku Band

A microstrip antenna with a circular disc design and modified ground is proposed in this paper. Circular shapes of different size have been slotted out from the radiating patch for achieving extended ultra wideband (UWB) with GSM/Bluetooth bands with maximum bandwidth of 17.7 GHz (0.88-18.6 GHz). Further, characteristic of dual notch band is achieved, when a combination of T and L-shaped slots are etched into the circular disc and ground plane respectively. Change in length of slots is controlling the notch band characteristics. The proposed antenna has rejection bandwidth of 1.3-2.2 GHz (LTE band), 3.2-3.9 GHz (WiMAX band) and 5.2-6.1 GHz (WLAN band) respectively. It covers the frequency range of 0.88-18.5 GHz with the VSWR of less than 2. Also, an equivalent parallel resonant circuit has been demonstrated for band notched frequencies of the designed antenna. The gain achieved by the proposed antenna is 6.27 dBi. This antenna has been designed, investigated and fabricated for GSM, Bluetooth, UWB, X and Ku band applications. The stable gain including H & E-plane radiation pattern with good directivity and omnidirectional behavior is achieved by the proposed antenna. Measured bandwidths are 0.5 GHz, 0.8 GHz, 1.1 GHz and 11.7 GHz respectively. 

Low-profile U-shaped DRA for ultra-wideband applications

2016 ◽  
Vol 9 (3) ◽  
pp. 621-627 ◽  
Author(s):  
Idris Messaoudene ◽  
Tayeb A. Denidni ◽  
Abdelmadjid Benghalia
Keyword(s):  
Dielectric Resonator ◽  
Ground Plane ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
Wide Bandwidth ◽  
Operating Band ◽  
Low Profile ◽  
Measurement Results

In this paper, a microstrip-fed U-shaped dielectric resonator antenna (DRA) is simulated, designed, and fabricated. This antenna, in its simple configuration, operates from 5.45 to 10.8 GHz. To enhance its impedance bandwidth, the ground plane is first modified, which leads to an extended bandwidth from 4 to 10.8 GHz. Then by inserting a rectangular metallic patch inside the U-shaped DRA, the bandwidth is increased more to achieve an operating band from 2.65 to 10.9 GHz. To validate these results, an experimental antenna prototype is fabricated and measured. The obtained measurement results show that the proposed antenna can provide an ultra-wide bandwidth and a symmetric bidirectional radiation patterns. With these features, the proposed antenna is suitable for ultra-wideband applications.

Sign in / Sign up

Export Citation Format

Share Document