Thermal Performance in Circular Tube with Co/Counter-Twisted Tapes

2014 ◽  
Vol 931-932 ◽  
pp. 1198-1202 ◽  
Author(s):  
Suriya Chokphoemphun ◽  
Chayodom Hinthao ◽  
Smith Eiamsa-ard ◽  
Pongjet Promvonge ◽  
Chinaruk Thianpong
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Circular Tube ◽  
Experimental Results ◽  
Enhanced Heat Transfer ◽  
Twisted Tapes ◽  
Twist Ratio

Thiswork presents an experimental study on enhanced heat transfer and pressure loss characteristics in a tube having a uniform heat-fluxed wall by using small double and triple co-and counter-twisted tapes at two twist ratios, y/w=4 and 4.5. The investigation has been conducted for Reynolds number from 5300-20,000. The experimental results of the heat transfer and pressure drop are proposed in terms of Nusselt number and friction factor, respectively.The experimental results reveal thatthe maximum TEF for the triple counter-twisted tapesat smaller twist ratio isabout 1.26.

scholarly journals Thermo-Hydraulic Performance Analysis on the Effects of Truncated Twisted Tape Inserts in a Tube Heat Exchanger

Symmetry ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 1652
Author(s):  
Mehdi Ghalambaz ◽  
Ramin Mashayekhi ◽  
Hossein Arasteh ◽  
Hafiz Muhammad Ali ◽  
Pouyan Talebizadehsardari ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Twisted Tape ◽  
Transfer Enhancement ◽  
Tube Heat Exchanger ◽  
Twisted Tapes ◽  
Plain Tube

This paper investigates the convective heat transfer in a heat exchanger equipped with twisted tape elements to examine effects of the twisted tape truncation percentage, pitch value, position and Reynolds number using 3D numerical simulation. A symmetric heat flux is applied around the tube as the studied heat exchanger. Based on the influences in both heat transfer enhancement and pressure drop, the performance evaluation criterion (PEC) is utilized. Inserting twisted tape elements and reducing the pitch value significantly augment the Nusselt number, friction coefficient and PEC number compared to the plain tube. For the best case with a Reynolds number of 1000, the average Nusselt number increases by almost 151%, which is the case of fully fitted twisted tape at a pitch value of L/4. Moreover, increasing the twisted tape truncation percentage reduces both heat transfer and pressure drop. Furthermore, the highest heat transfer rate is achieved when the truncated twisted tape is located at the entrance of the tube. Finally, it is concluded that for P = L, L/2, L/3 and L/4, the optimum cases from the viewpoint of energy conservation are twisted tapes with truncation percentages of 75, 50, 50 and 0%, in which the related PEC numbers at a Reynolds number of 1000 are almost equal to 1.08, 1.24, 1.4 and 1.76, respectively.

Enhancement of Heat Transfer of Rectangular Saw Tooth Shaped Micro Channel Heat Sink with Water Nano Fluid/Aluminium Oxide

2015 ◽  
Vol 813-814 ◽  
pp. 685-689
Author(s):  
M. Vijay Anand Marimuthu ◽  
B. Venkatraman ◽  
S. Kandhasamy
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Heat Sink ◽  
Micro Channel ◽  
Performance Curve ◽  
Theoretical Level ◽  
Enhancement Of Heat Transfer ◽  
Nano Fluid

This paper investigates the performance and characteristics of saw tooth shape micro channel in the theoretical level. If the conduct area of the nano fluid increases the heat transfer also increases. The performance curve has drawn Reynolds number against nusselt number, heat transfer co efficient. Pressure drop plays an important role in this device. If pressure drop is high the heat transfer increases. The result in this experiment shows clearly that the heat transfer is optimized.

Heat Transfer Enhancement in a Rectangular (AR = 3:1) Channel With V-Shaped Dimples

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
C. Neil Jordan ◽  
Lesley M. Wright
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Liquid Crystal ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Secondary Flows ◽  
Transfer Enhancement ◽  
Reduced Pressure

An alternative to ribs for internal heat transfer enhancement of gas turbine airfoils is dimpled depressions. Relative to ribs, dimples incur a reduced pressure drop, which can increase the overall thermal performance of the channel. This experimental investigation measures detailed Nusselt number ratio distributions obtained from an array of V-shaped dimples (δ/D = 0.30). Although the V-shaped dimple array is derived from a traditional hemispherical dimple array, the V-shaped dimples are arranged in an in-line pattern. The resulting spacing of the V-shaped dimples is 3.2D in both the streamwise and spanwise directions. A single wide wall of a rectangular channel (AR = 3:1) is lined with V-shaped dimples. The channel Reynolds number ranges from 10,000–40,000. Detailed Nusselt number ratios are obtained using both a transient liquid crystal technique and a newly developed transient temperature sensitive paint (TSP) technique. Therefore, the TSP technique is not only validated against a baseline geometry (smooth channel), but it is also validated against a more established technique. Measurements indicate that the proposed V-shaped dimple design is a promising alternative to traditional ribs or hemispherical dimples. At lower Reynolds numbers, the V-shaped dimples display heat transfer and friction behavior similar to traditional dimples. However, as the Reynolds number increases to 30,000 and 40,000, secondary flows developed in the V-shaped concavities further enhance the heat transfer from the dimpled surface (similar to angled and V-shaped rib induced secondary flows). This additional enhancement is obtained with only a marginal increase in the pressure drop. Therefore, as the Reynolds number within the channel increases, the thermal performance also increases. While this trend has been confirmed with both the transient TSP and liquid crystal techniques, TSP is shown to have limited capabilities when acquiring highly resolved detailed heat transfer coefficient distributions.

scholarly journals Experimental study on turbulent convective heat transfer, pressure drop, and thermal performance characterization of ZnO/water nanofluid flow in a circular tube

2014 ◽  
Vol 18 (4) ◽  
pp. 1315-1326 ◽  
Author(s):  
Ahmad Sajadi ◽  
Seyed Sadati ◽  
Masoud Nourimotlagh ◽  
Omid Pakbaz ◽  
Dariush Ashtiani ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Thermal Performance ◽  
Base Fluid ◽  
Circular Tube ◽  
Turbulent Regime ◽  
Nanofluid Flow ◽  
Volume Fractions

In this experimental study heat transfer and pressure drop behavior of ZnO/water nanofluid flow inside a circular tube with constant wall temperature condition is investigated where the volume fractions of nanoparticles in the base fluid are 1% and 2%. The experiments? Reynolds numbers ranged roughly from 5000 to 30000. The experimental measurements have been carried out in the fully-developed turbulent regime. The results indicated that heat transfer coefficient increases by 11% and 18% with increasing volume fractions of nanoparticles respectively to 1% and 2% vol. The measurements also showed that the pressure drop of nanofluids were respectively 45% and145% higher than that of the base fluid for volume fractions of 1% and 2% of nanoparticles. However experimental results revealed that overall thermal performance of nanofluid is higher than that of pure water by up to 16% for 2% vol. nanofluid. Also experimental results proved that existing correlations can accurately estimate nanofluids convective heat transfer coefficient and friction factor in turbulent regime, provided that thermal conductivity, heat capacity, and viscosity of the nanofluids are used in calculating the Reynolds, Prandtl, and Nusselt numbers.

Thermohydraulic Study of Laminar Swirl Flow Through a Circular Tube Fitted With Twisted Tapes

2001 ◽  
Vol 123 (3) ◽  
pp. 417-427 ◽  
Author(s):  
S. K. Saha ◽  
A. Dutta
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Prandtl Number ◽  
Friction Factor ◽  
Circular Tube ◽  
Swirl Flow ◽  
Short Length ◽  
Full Length ◽  
Twisted Tape ◽  
Twisted Tapes

Heat transfer and pressure drop characteristics in a circular tube fitted with twisted tapes have been investigated experimentally. Laminar swirl flow of a large Prandtl number 205<Pr<518 viscous fluid was considered. The swirl was generated by short-length twisted-tape inserts; regularly spaced twisted-tape elements with multiple twists in the tape module and connected by thin circular rods; and smoothly varying (gradually decreasing) pitch twisted-tapes. The heat transfer test section was heated electrically imposing axially and circumferentially constant wall heat flux (UHF) boundary condition. Reynolds number, Prandtl number, twist ratio, space ratio, number of tuns in the tape module, length of the twisted-tape and smoothness of the swirling pitch govern the characteristics. Friction factor and Nusselt number are lower for short-length twisted-tape than those for full-length twisted-tape. On the basis of constant pumping power and constant heat duty, however, short-length twisted-tapes are found to perform better than full-length twisted-tapes for tighter twists. Thermohydraulic performance shows that twisted-tapes with multiple twists in the tape module is not much different from that with single twist in the tape module. Friction factor and Nusselt number are approximately 15 percent lower for twisted-tapes with smooth swirl having the average pitch same as that of the uniform pitch (throughout) twisted-tape and the twisted-tapes with gradually decreasing pitch perform worse than their uniform-pitch counterparts.

scholarly journals Effect of Pin Diameter Degressive Gradient on Heat Transfer in a Microreactor with Non-Uniform Pin-Fin Array under Low Reynolds Number Conditions

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2702
Author(s):  
Miao Qian ◽  
Jie Li ◽  
Zhong Xiang ◽  
Chao Yan ◽  
Xudong Hu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Low Reynolds Number ◽  
Hydrodynamic Characteristics ◽  
Pin Fin ◽  
Low Reynolds ◽  
Pin Fin Array

To improve the efficiency of hydrogen-producing microreactors with non-uniform pin-fin array, the influence of the pin diameter degressive gradient of the non-uniform pin-fin array (NPFA) on heat transfer and pressure drop characteristics is analyzed in this study via numerical simulation under low Reynolds number conditions. Because correlations in prior studies cannot be used to predict the Nusselt number and pressure drop in the NPFA, new heat transfer and friction factor correlations are developed in this paper to account for the effect of the pin diameter degressive gradient, providing a method for the optimized design of the pin diameter degressive gradient for a microreactor with NPFA. The results show that the Nusselt number and friction factor under a low Reynolds number are quite sensitive to the pin diameter degressive gradient. Based on the new correlations, the exponents of the pin diameter degressive gradient for the friction factor and Nusselt number were 6.9 and 2.1, respectively, indicating the significant influence of the pin diameter degressive gradient on the thermal and hydrodynamic characteristics in the NPFA structure.

scholarly journals Improvement of cooling performance of hybrid nanofluids in a heated pipe applying annular magnets

2021 ◽  
Author(s):  
Guolong Li ◽  
Jin Wang ◽  
Hongxing Zheng ◽  
Gongnan Xie ◽  
Bengt Sundén
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Carbon Nanotubes ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Volume Fraction ◽  
Circular Tube ◽  
Hybrid Nanofluid ◽  
Inner Diameter ◽  
Hybrid Nanofluids

AbstractIn this paper, convective heat transfer of Fe3O4–carbon nanotubes (CNTs) hybrid nanofluid was studied in a horizontal small circular tube under influence of annular magnets. The pipe has an inner diameter of 3 mm and a length of 1.2 m. Heat transfer characteristics of the Fe3O4–water nanofluid were examined for many parameters, such as nanoparticle volume fraction in the range of 0.4–1.2% and Reynolds number in the range of 476–996. In order to increase the thermal conductivity of the Fe3O4–water nanofluid, carbon nanotubes with 0.12–0.48% volume fraction were added into the nanofluid. It was observed that for the Fe3O4–CNTs–water nanofluid with 1.44% volume fraction and under a magnetic field, the maximal local Nusselt number at the Reynolds number 996 increased by 61.54% compared with without a magnetic field. Results also show that compared with the deionized water, the maximal enhancements of the average Nusselt number are 67.9 and 20.89% for the Fe3O4–CNTs–water nanofluid with and without magnetic field, respectively.

Sign in / Sign up

Export Citation Format

Share Document