Effects of Re Alloying on Mechanical Properties of In-Situ Composites with Base Composition of Nb-18Si-2HfC

2006 ◽  
Vol 306-308 ◽  
pp. 941-946
Author(s):  
Sheng Wu Wang ◽  
Tatsuo Tabaru ◽  
Hisatoshi Hirai ◽  
Hideto Ueno
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Temperature ◽  
Base Composition ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Strengthening Effect ◽  
In Situ Composites ◽  
Temperature Fracture

Nb-base in-situ composites with the base composition of Nb-18Si-2HfC were prepared by conventional arc-melting. Their microstructures and mechanical properties, such as high-temperature strength and room temperature fracture toughness, were investigated to elucidate the effects of Re alloying. The in-situ composites predominantly have eutectic microstructures consisting of an Nb solid solution (NbSS) and Nb5Si3. The compressive strength increased with the increasing Re contents at 1470K and not at 1670 K. The strengthening effect observed at 1470 K is higher than that by W and Mo. Re alloying of about 2 % is valuable for improving both the high temperature strength and room temperature fracture toughness of Nb-18Si-2HfC base materials.

Microstructures and Properties of Ds in-Situ Composites of Nb-Ti-Si Alloys

1994 ◽  
Vol 364 ◽  
Author(s):  
B. P. Bewlay ◽  
M. R. Jackson ◽  
W. J. Reeder ◽  
H. A. Lipsitt
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Fracture Toughness ◽  
Room Temperature ◽  
In Situ Composites ◽  
Environmental Resistance ◽  
High Temperature Mechanical Properties ◽  
Three Phase ◽  
Temperature Fracture

AbstractIn-situ composites based on binary Nb-Si alloys and consisting of a Nb solid solution with Nb3Si or Nb5Si3 have shown a promising combination of low temperature and high temperature mechanical properties. The environmental resistance and room temperature fracture toughness of these composites can be further enhanced by additions such as Ti, Hf, Cr, and Al. In the present study, ternary Nb-Ti-Si alloys were prepared by directional solidification to generate aligned two and three phase composites containing a Nb solid solution with Nb3Si and/or Nb5Si3. The present paper will describe microstructures, phase equilibria and fracture toughness of these composites. The improvement in the room temperature fracture toughness over binary Nb-Nb5Si3 composites is discussed.

Mechanical properties of NiAl-Mo composites produced by specially controlled directional solidification

2012 ◽  
Vol 1516 ◽  
pp. 255-260 ◽  
Author(s):  
G. Zhang ◽  
L. Hu ◽  
W. Hu ◽  
G. Gottstein ◽  
S. Bogner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Directional Solidification ◽  
Creep Resistance ◽  
Room Temperature ◽  
Growth Direction ◽  
Nominal Composition ◽  
Potential Candidate ◽  
In Situ Composites

ABSTRACTMo fiber reinforced NiAl in-situ composites with a nominal composition Ni-43.8Al-9.5Mo (at.%) were produced by specially controlled directional solidification (DS) using a laboratory-scale Bridgman furnace equipped with a liquid metal cooling (LMC) device. In these composites, single crystalline Mo fibers were precipitated out through eutectic reaction and aligned parallel to the growth direction of the ingot. Mechanical properties, i.e. the creep resistance at high temperatures (HT, between 900 °C and 1200 °C) and the fracture toughness at room temperature (RT) of in-situ NiAl-Mo composites, were characterized by tensile creep (along the growth direction) and flexure (four-point bending, vertical to the growth direction) tests, respectively. In the current study, a steady creep rate of 10-6s-1 at 1100 °C under an initial applied tensile stress of 150MPa was measured. The flexure tests sustained a fracture toughness of 14.5 MPa·m1/2at room temperature. Compared to binary NiAl and other NiAl alloys, these properties showed a remarkably improvement in creep resistance at HT and fracture toughness at RT that makes this composite a potential candidate material for structural application at the temperatures above 1000 °C. The mechanisms responsible for the improvement of the mechanical properties in NiAl-Mo in-situ composites were discussed based on the investigation results.

Microstructure and room temperature fracture toughness of Nbss/Nb5Si3 in situ composites

2001 ◽  
Vol 9 (9) ◽  
pp. 827-834 ◽  
Author(s):  
Won-Yong Kim ◽  
Hisao Tanaka ◽  
Akio Kasama ◽  
Shuji Hanada
Keyword(s):  
Fracture Toughness ◽  
Room Temperature ◽  
In Situ Composites ◽  
Temperature Fracture

Strength and Toughness of Silicide Matrix Materials Consolidated by Hot Isostatic Pressing

1993 ◽  
Vol 322 ◽  
Author(s):  
R. Suryanarayanan ◽  
S. M. L. Sastry ◽  
K. L. Jerina
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Creep Resistance ◽  
Room Temperature ◽  
Hot Isostatic Pressing ◽  
Molybdenum Disilicide ◽  
High Temperature Strength ◽  
Isostatic Pressing ◽  
Temperature Fracture ◽  
Hip Process

AbstractSubstantial improvements have been reported in high temperature strength and creep resistance, and room temperature fracture toughness of molybdenum disilicide (MoSi2) reinforced with ductile or brittle reinforcements. The influence of Hot Isostatic Pressing (HIP) process parameters on the mechanical properties of MoSi2 based alloys was studied. Monolithic MoSi2 powder and MoSi2 powder blended with either niobium powder or silicon carbide whisker reinforcements were consolidated by HIP at 1200 − 1400°C, 207 MPa, and 1 - 4 hrs. The HIP'ed compacts were characterized for compression strength and creep resistance at 1100-1300°C. Fracture toughness was measured on single edge notched rectangular specimens at room temperature. Mechanical properties were correlated with post-HIP microstructural features.

Effect of B4C on the Mechanical Properties and Microstructure of ZrB2-SiC Based Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 218-221 ◽  
Author(s):  
Xuan Liu ◽  
Qiang Xu ◽  
Shi Zhen Zhu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Temperature ◽  
Relative Density ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Room Temperature Strength

ZrB2-SiC-B4C is sintered at 1700°C by spark plasma sintering process. The effect of B4C content on the mechanical properties and microstructure of ZrB2-SiC based ceramics is studied. The results show that, with the content of B4C increases, the relative density and room-temperature strength decrease in the ZrB2-SiC-B4C composite. The fracture toughness rises at first and then falls down. The high temperature strength increases.

The Fracture Toughness and DBTT of MoB Particle-Reinforced MoSi2 Composites

2007 ◽  
Vol 280-283 ◽  
pp. 1471-1474
Author(s):  
Zhi Xiong ◽  
Gang Wang ◽  
Wan Jiang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Temperature ◽  
Room Temperature ◽  
Probable Mechanism ◽  
Vickers Indentation ◽  
Indentation Technique ◽  
Testing Method ◽  
Temperature Fracture

The room temperature fracture toughness and the high temperature DBTT of MoB particle-reinforced MoSi2 composites were investigated using Vickers indentation technique and MSP testing method， respectively. Modified Small Punch (MSP) test is a method for evaluation of mechanical properties using very small specimens, and it’s appropriate for the determination of strength and DBTT. It was found that the approximate fracture toughness of the composite is 1.3 times that of monolithic MoSi2, and its DBTT is 100°C higher than that of monolithic MoSi2 materials. Cracks deflection is a probable mechanism responsible for this behavior.

Microstructure and room temperature fracture toughness of directionally solidified NiAl–Mo eutectic in situ composites

2012 ◽  
Vol 21 (1) ◽  
pp. 18-25 ◽  
Author(s):  
Jian-Fei Zhang ◽  
Jun Shen ◽  
Zhao Shang ◽  
Zhou-Rong Feng ◽  
Ling-Shui Wang ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Room Temperature ◽  
Directionally Solidified ◽  
In Situ Composites ◽  
Temperature Fracture
Sign in / Sign up

Export Citation Format

Share Document